Hi Everyone, could someone please tell me how can I convert a rtsp address to a channel for viewing?
I had tried using M3u bouquet converter but it didn’t work.
Thanks very much
Posted 22 August 2018 - 18:20
Hi,
If you link is:
rtsp://5.196.138.6:1935/live/nrjbelgique_360p
You need to create this into your userbouquet file:
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Posted 22 August 2018 - 23:07
Hi Pr2 & Rick Hunter, thanks very much for the advice.
If the address is, “ rtsp://admin:123456@192.168.1.75:10554/tcp/av0_1 “ (user name: admin, password: 123456), then am I right to say the result is as follows?
#SERVICE 4097:0:1:0:0:0:0:0:0:0:rtsp%3a//admin%3a123456@192.168.1.75%3a10554/tcp/av0_1:Corridor Cam
#DESCRIPTION Corridor Cam
I tried the above but no image appear.
Please tell me what has I not done correctly?
Thanks & Best Regards
Posted 23 August 2018 - 20:37
Yes I didn't find errors in your conversion.
But it is possible that rtsp stream that needs authentication is not supported by #SERVICE 4097 player.
There is a plugin available to handle IP Camera:
opkg update opkg install enigma2-plugin-extensions-webcamviewer
Perhaps give it a try.
Pr2
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Posted 4 March 2019 - 21:00
Hi All,
I just bought a Cloud based IP camera, without realising that it's realy a way for the seller to sell your cloud storage. It was only £20 delivered. (ebay).
So did some searching and found opensource http://www.ispyconnect.com
The user guide is realy detailed and the software is over the top, but I couldn't my head around it.
So here's my problem. I would like to the software or something similar to connect to my IP-Cam (WiFi/LAN).
Then ultimately access it as a channel on my Xtrend et8000 and/or other stb's on my LAN (my PC never sleeps).
So far I can access it via VLC on "rtsp://admin:admin@192.168.0.9/ch0_0.h264" and it streams great. They have a little widget that creates this based on camera make and ip address.
They call the IP-Cam "Eyeplus: EYEPLUS_DEV" It has a Device ID "AJWL1809301018ETAxxxxxxxxxxxxxx". And a valid MAC for either LAN or WiFi.
Could anyone either point me to a Forum for IP-Camera's or point me in the right direction.
Thanks in advance Colin
Xtrend et8000 7.1-Release
2 x 8/1 DiSEqC 30w 13e 19e 23e 28e
Astrometa USB Tuner Working DVB-T2 now on Kernel 4.10+
WD10EARX 1TB
Sandisk 32GB USB for AFB, EPG, Picons & Timeshift
ZGemma Star S 7.0-Release
4/1 DiSEqC 30w 13e 19e 28e
Sandisk 8GB USB for AFB, EPG, Picons & Timeshift
LG 49UH610V UHD-HDR
UHF/Cable/Sat
E-Channelizer
Posted 4 March 2019 - 21:33
ffprobe rtsp://admin:admin@192.168.0.9/ch0_0.h264
Posted 4 March 2019 - 22:09
Hi,
Assuming that you have ffmpeg installed (opkg install ffmpeg) what does the following return?
ffprobe rtsp://admin:admin@192.168.0.9/ch0_0.h264
@athoik, thanks for your learned reply.
I've put it away for tonight. Was doing the setup on the floor before install.
I will give it a try in the morning.
Thanks Colin
Xtrend et8000 7.1-Release
2 x 8/1 DiSEqC 30w 13e 19e 23e 28e
Astrometa USB Tuner Working DVB-T2 now on Kernel 4.10+
WD10EARX 1TB
Sandisk 32GB USB for AFB, EPG, Picons & Timeshift
ZGemma Star S 7.0-Release
4/1 DiSEqC 30w 13e 19e 28e
Sandisk 8GB USB for AFB, EPG, Picons & Timeshift
LG 49UH610V UHD-HDR
UHF/Cable/Sat
E-Channelizer
Posted 5 March 2019 - 09:28
Failed first time then I removed a password and now:
[rtsp @ 0x445550] method DESCRIBE failed: 401 Unauthorized
rtsp://admin:admin@192.168.0.9/ch0_0.h264: Server returned 401 Unauthorized (authorization failed)
root@et8000:~# ffprobe rtsp://admin:@192.168.0.9/ch0_0.h264
ffprobe version 3.4.2 Copyright © 2007-2018 the FFmpeg developers
built with gcc 6.3.0 (GCC)
configuration: --disable-stripping --enable-pic --enable-shared --enable-pthreads --disable-libxcb --disable-libxcb-sh
m --disable-libxcb-xfixes --disable-libxcb-shape --enable-nonfree --cross-prefix=mipsel-oe-linux- --ld='mipsel-oe-linux-
gcc -mel -mabi=32 -mhard-float -march=mips32 --sysroot=/openpli/oe/release-7.0/build/tmp/work/mips32el-oe-linux/ffmpeg/3
.4.2-r0/recipe-sysroot' --cc='mipsel-oe-linux-gcc -mel -mabi=32 -mhard-float -march=mips32 --sysroot=/openpli/oe/release
-7.0/build/tmp/work/mips32el-oe-linux/ffmpeg/3.4.2-r0/recipe-sysroot' --cxx='mipsel-oe-linux-g++ -mel -mabi=32 -mhard-fl
oat -march=mips32 --sysroot=/openpli/oe/release-7.0/build/tmp/work/mips32el-oe-linux/ffmpeg/3.4.2-r0/recipe-sysroot' --a
rch=mipsel --target-os=linux --enable-cross-compile --extra-cflags=' -O2 -pipe -g -feliminate-unused-debug-types -fdebug
-prefix-map=/openpli/oe/release-7.0/build/tmp/work/mips32el-oe-linux/ffmpeg/3.4.2-r0=/usr/src/debug/ffmpeg/3.4.2-r0 -fde
bug-prefix-map=/openpli/oe/release-7.0/build/tmp/work/mips32el-oe-linux/ffmpeg/3.4.2-r0/recipe-sysroot-native= -fdebug-p
refix-map=/openpli/oe/release-7.0/build/tmp/work/mips32el-oe-linux/ffmpeg/3.4.2-r0/recipe-sysroot= -mel -mabi=32 -mhard-
float -march=mips32 --sysroot=/openpli/oe/release-7.0/build/tmp/work/mips32el-oe-linux/ffmpeg/3.4.2-r0/recipe-sysroot' -
-extra-ldflags='-Wl,-O1 -Wl,--as-needed' --sysroot=/openpli/oe/release-7.0/build/tmp/work/mips32el-oe-linux/ffmpeg/3.4.2
-r0/recipe-sysroot --enable-hardcoded-tables --disable-static --disable-runtime-cpudetect --enable-ffprobe --disable-alt
ivec --disable-amd3dnow --disable-amd3dnowext --disable-mmx --disable-mmxext --disable-sse --disable-sse2 --disable-sse3
--disable-ssse3 --disable-sse4 --disable-sse42 --disable-avx --disable-xop --disable-fma3 --disable-fma4 --disable-avx2
--enable-inline-asm --enable-asm --disable-x86asm --disable-fast-unaligned --enable-muxers --enable-encoders --enable-d
ecoders --enable-demuxers --enable-parsers --enable-bsfs --enable-protocols --enable-indevs --enable-outdevs --enable-fi
lters --disable-doc --disable-htmlpages --disable-manpages --disable-podpages --disable-txtpages --enable-mipsfpu --disa
ble-vfp --disable-neon --disable-mipsdsp --disable-mipsdspr2 --disable-debug --pkg-config=pkg-config --enable-zlib --ext
ra-cflags=' -O2 -pipe -g -feliminate-unused-debug-types -fdebug-prefix-map=/openpli/oe/release-7.0/build/tmp/work/mips32
el-oe-linux/ffmpeg/3.4.2-r0=/usr/src/debug/ffmpeg/3.4.2-r0 -fdebug-prefix-map=/openpli/oe/release-7.0/build/tmp/work/mip
s32el-oe-linux/ffmpeg/3.4.2-r0/recipe-sysroot-native= -fdebug-prefix-map=/openpli/oe/release-7.0/build/tmp/work/mips32el
-oe-linux/ffmpeg/3.4.2-r0/recipe-sysroot= -mel -mabi=32 -mhard-float -march=mips32 --sysroot=/openpli/oe/release-7.0/bui
ld/tmp/work/mips32el-oe-linux/ffmpeg/3.4.2-r0/recipe-sysroot -ffunction-sections -fdata-sections -fno-aggressive-loop-op
timizations' --extra-ldflags='-Wl,-O1 -Wl,--as-needed,--gc-sections -Wl,--print-gc-sections,-lrt' --prefix=/usr --libdir
=/usr/lib --shlibdir=/usr/lib --datadir=/usr/share/ffmpeg --disable-mipsdsp --disable-mipsdspr2 --cpu=generic --pkg-conf
ig=pkg-config --enable-avcodec --enable-avdevice --enable-avfilter --enable-avformat --enable-avresample --enable-bzlib
--enable-gpl --disable-libgsm --disable-indev=jack --enable-libbluray --enable-protocol=bluray --enable-libfreetype --en
able-librtmp --enable-libvorbis --enable-lzma --enable-libmp3lame --enable-openssl --enable-postproc --disable-sdl2 --di
sable-libspeex --enable-swresample --enable-swscale --enable-libtheora --disable-vaapi --disable-vdpau --enable-libvpx -
-enable-libx264 --disable-outdev=xv
libavutil 55. 78.100 / 55. 78.100
libavcodec 57.107.100 / 57.107.100
libavformat 57. 83.100 / 57. 83.100
libavdevice 57. 10.100 / 57. 10.100
libavfilter 6.107.100 / 6.107.100
libavresample 3. 7. 0 / 3. 7. 0
libswscale 4. 8.100 / 4. 8.100
libswresample 2. 9.100 / 2. 9.100
libpostproc 54. 7.100 / 54. 7.100
Input #0, rtsp, from 'rtsp://admin:@192.168.0.9/ch0_0.h264':
Metadata:
title : h264.mp4
comment : TAS-Tech Live Cast
Duration: N/A, start: 0.595800, bitrate: N/A
Stream #0:0: Video: h264 (Main), yuv420p(progressive), 1920x1080, 11.92 fps, 25 tbr, 90k tbn, 23.75 tbc
root@et8000:~# ffprobe rtsp://admin:@192.168.0.9/ch0_0.h264
Xtrend et8000 7.1-Release
2 x 8/1 DiSEqC 30w 13e 19e 23e 28e
Astrometa USB Tuner Working DVB-T2 now on Kernel 4.10+
WD10EARX 1TB
Sandisk 32GB USB for AFB, EPG, Picons & Timeshift
ZGemma Star S 7.0-Release
4/1 DiSEqC 30w 13e 19e 28e
Sandisk 8GB USB for AFB, EPG, Picons & Timeshift
LG 49UH610V UHD-HDR
UHF/Cable/Sat
E-Channelizer
Posted 5 March 2019 - 10:06
Just to let you know. I got the iSpy software seeing the camera, just by removing the password.
Sill wanting to pursue making it visable to my stb's
cheers Colin
Xtrend et8000 7.1-Release
2 x 8/1 DiSEqC 30w 13e 19e 23e 28e
Astrometa USB Tuner Working DVB-T2 now on Kernel 4.10+
WD10EARX 1TB
Sandisk 32GB USB for AFB, EPG, Picons & Timeshift
ZGemma Star S 7.0-Release
4/1 DiSEqC 30w 13e 19e 28e
Sandisk 8GB USB for AFB, EPG, Picons & Timeshift
LG 49UH610V UHD-HDR
UHF/Cable/Sat
E-Channelizer
Posted 9 March 2019 - 10:36
This is the VLC stream that works for my IP-Cam
rtsp://admin:admin@192.168.0.9/ch0_0.h264
Could anyone help change it to a service Ref: ?
Xtrend et8000 7.1-Release
2 x 8/1 DiSEqC 30w 13e 19e 23e 28e
Astrometa USB Tuner Working DVB-T2 now on Kernel 4.10+
WD10EARX 1TB
Sandisk 32GB USB for AFB, EPG, Picons & Timeshift
ZGemma Star S 7.0-Release
4/1 DiSEqC 30w 13e 19e 28e
Sandisk 8GB USB for AFB, EPG, Picons & Timeshift
LG 49UH610V UHD-HDR
UHF/Cable/Sat
E-Channelizer
Posted 9 March 2019 - 13:50
You could try :
#SERVICE 4097:0:1:0:0:0:0:0:0:0:rtsp%3a//admin%3aadmin@192.168.0.9/ch0_0.h264:NameOfYourStream #DESCRIPTION NameOfYourStream
@oxejatte Thank you so much worked perfect first-time. In my case I removed the password.
4097_0_1_0_0_0_0_0_0_0_20190309114119.jpg 80.85KB
7 downloads
Unfortunately I've ran into another issue. which in my case also happens with the "WebcamStreamer" plugin.
The camera either lock's up, or is shutdown (the camera has no power lights). Requiring the Camera to be manually rebooted.
Also it is no longer available to telnet, vlc or the iSpy software I'm using.
Anyway this thread was about Rtsp to Channel which is what I've confirmed.
Many thanks
Xtrend et8000 7.1-Release
2 x 8/1 DiSEqC 30w 13e 19e 23e 28e
Astrometa USB Tuner Working DVB-T2 now on Kernel 4.10+
WD10EARX 1TB
Sandisk 32GB USB for AFB, EPG, Picons & Timeshift
ZGemma Star S 7.0-Release
4/1 DiSEqC 30w 13e 19e 28e
Sandisk 8GB USB for AFB, EPG, Picons & Timeshift
LG 49UH610V UHD-HDR
UHF/Cable/Sat
E-Channelizer
Posted 9 March 2019 - 16:59
Posted 9 March 2019 - 17:31
Stream #0:0: Video: h264 (Main), yuv420p(progressive), 1920x1080, 11.92 fps, 25 tbr, 90k tbn, 23.75 tbc
11.92 fps is not so common, something like 25 should be better for receiver.
@athoik, thanks for your interest, but you have me lost there. I can say that using VLC compared to the iSpy (opensource) software the difference is noticable.
iSpy-VLC-Comparison-01.PNG 910.97KB
2 downloads
At the moment I have NO direct access to the camera internal software. It responds to telnet with normal user login, 3 attempt timeout. So I am waiting to see if supplier will give password.
Today, FYI:
root@et8000:~# ffprobe rtsp://admin:@192.168.0.9/ch0_0.h264...
...Input #0, rtsp, from 'rtsp://admin:@192.168.0.9/ch0_0.h264':
Metadata:
title : h264.mp4
comment : TAS-Tech Live Cast
Duration: N/A, start: 0.475800, bitrate: N/A
Stream #0:0: Video: h264 (Main), yuv420p(progressive), 1920x1080, 11.92 fps, 25 tbr, 90k tbn, 23.75 tbc
root@et8000:~#
Xtrend et8000 7.1-Release
2 x 8/1 DiSEqC 30w 13e 19e 23e 28e
Astrometa USB Tuner Working DVB-T2 now on Kernel 4.10+
WD10EARX 1TB
Sandisk 32GB USB for AFB, EPG, Picons & Timeshift
ZGemma Star S 7.0-Release
4/1 DiSEqC 30w 13e 19e 28e
Sandisk 8GB USB for AFB, EPG, Picons & Timeshift
LG 49UH610V UHD-HDR
UHF/Cable/Sat
E-Channelizer
Posted 9 March 2019 - 17:38
Posted 9 March 2019 - 18:05
The ffmpeg reports 11.92 frames per second.
Usually the videos that a receiver is able to play is 25fps, 50fps, 60fps.
So if the camera has option for 25pfs it might work on your receiver.
Post#14
I can access it via VLC on "rtsp://admin:admin@192.168.0.9/ch0_0.h264" and it streams great. Stop and start VLC has no problem. In fact VLC seems to have the best picture/resolution.
On my et8000 using as a channel: #SERVICE 4097:0:1:0:0:0:0:0:0:0:rtsp%3a//admin%3@192.168.0.9/ch0_0.h264 also works one time, but when I close the stream it locks or power off the camera. I then need to reboot the camera at the power switch.
Xtrend et8000 7.1-Release
2 x 8/1 DiSEqC 30w 13e 19e 23e 28e
Astrometa USB Tuner Working DVB-T2 now on Kernel 4.10+
WD10EARX 1TB
Sandisk 32GB USB for AFB, EPG, Picons & Timeshift
ZGemma Star S 7.0-Release
4/1 DiSEqC 30w 13e 19e 28e
Sandisk 8GB USB for AFB, EPG, Picons & Timeshift
LG 49UH610V UHD-HDR
UHF/Cable/Sat
E-Channelizer
Posted 9 March 2019 - 18:11
in my case also happens with the "WebcamStreamer" plugin.
Xtrend et8000 7.1-Release
2 x 8/1 DiSEqC 30w 13e 19e 23e 28e
Astrometa USB Tuner Working DVB-T2 now on Kernel 4.10+
WD10EARX 1TB
Sandisk 32GB USB for AFB, EPG, Picons & Timeshift
ZGemma Star S 7.0-Release
4/1 DiSEqC 30w 13e 19e 28e
Sandisk 8GB USB for AFB, EPG, Picons & Timeshift
LG 49UH610V UHD-HDR
UHF/Cable/Sat
E-Channelizer
0 members, 5 guests, 0 anonymous users