As title says. Started recently, was on 09\04, updated to 09\17, still the same.
Not done anything to receiver settings. Any hints ?
Thanks.
Deep standby = Restart (Solo2)
Started by 4wd, 20 Sep 2018 12:04
4 replies to this topic
#1
-
- Member
- 21 posts
0
Neutral
Posted 20 September 2018 - 12:04
Norway\France, 2x Solo2, OpenPli 6.2, CM180, T90, 125cm, 90cm motor
Re: Deep standby = Restart (Solo2) #2
-
- Member
- 21 posts
0
Neutral
Posted 20 September 2018 - 17:39
Found it 
solo2 was lately connected to monitor through a 4-1 HDMI switch.
When another receiver is connected to the switch (receiver power on, switch input set to solo2), the solo2 does it's restart from deep standby.
Without the switch, or without other receiver connected to switch, all well. So some strange HDMI command jumps around ?
Edited by 4wd, 20 September 2018 - 17:40.
Norway\France, 2x Solo2, OpenPli 6.2, CM180, T90, 125cm, 90cm motor
Re: Deep standby = Restart (Solo2) #3
-
- PLi® Contributor
- 6,075 posts
+257
Excellent
Posted 20 September 2018 - 17:50
You probably need to fine tune your HDMI-CEC settings.
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Re: Deep standby = Restart (Solo2) #4
-
- PLi® Core member
- 68,625 posts
+1,739
Excellent
Posted 20 September 2018 - 17:56
You can configure on the box to which HMDI command it needs to respond, I think the description says "from TV" but it is from any other device as HDMI-CEC is a bus.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: Deep standby = Restart (Solo2) #5
-
- Member
- 21 posts
0
Neutral
Posted 21 September 2018 - 10:55
Thanks for replies.
Yes, probably cec related, but can't figure it out. cec off on both units, monitor no cec. Somehow the 2nd receiver with power on passes on some command trough the hdmi switch, even when it's input not selected on the switch (switch set to solo2).
Anyway, it's not a problem just a curiosity. Cure: in current setup, power down 2nd receiver before power down on solo2.
.
Norway\France, 2x Solo2, OpenPli 6.2, CM180, T90, 125cm, 90cm motor
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users
