32 replies to this topic

[Drago]

ok immagini impostazioni allegate

 

ok images attached settings

Attached Files

•  audio e video.jpg   82.21KB   0 downloads
•  hdmicec.jpg   116.26KB   1 downloads
•  interfaccia ut1.jpg   175.73KB   0 downloads
•  interfaccia ut2.jpg   133.83KB   0 downloads
•  mod utente.jpg   72.2KB   0 downloads
•  personalizzazioni.jpg   159.79KB   0 downloads

[Drago]

intermittent operation

 

Rx: 09:04:13  <Give OSD Name>             <  46 

Tx: 09:04:13  <Set OSD Name>              >  47 osmini                                          [0x00]

Rx: 09:04:14  <Give OSD Name>             <  46 

Tx: 09:04:14  <Set OSD Name>              >  47 osmini                                          [0x00]

Rx: 09:04:14  <Give Device Vendor ID>     <  8C 

Tx: 09:04:14  <Device Vendor ID>          >  87 00 00 00                                        [0x00]

Rx: 09:04:14  <Give OSD Name>             <  46 

Tx: 09:04:14  <Set OSD Name>              >  47 osmini                                          [0x00]

Rx: 09:04:14  <Feature Abort>             <  00 87 00 

Tx: 09:05:09  <Standby>                   >  36                                                 [0x00]

Rx: 09:05:10  <Standby>                   <  36 

Rx: 09:06:10  <Standby>                   <  36 

Rx: 09:06:27  <Report Power Status>       <  90 00 

Rx: 09:06:30  <Report Power Status>       <  90 00 

Rx: 09:06:30  <Routing Change>            <  80 00 00 40 00 

Rx: 09:06:30  <Report Physical Address>   <  84 00 00 00 

Rx: 09:06:31  <Device Vendor ID>          <  87 00 00 39 

Rx: 09:06:31  <Give Physical Address>     <  83 

Tx: 09:06:31  <Report Physical Address>   >  84 40 00 03                                        [0x0F]

Rx: 09:06:31  <Give OSD Name>             <  46 

Tx: 09:06:31  <Set OSD Name>              >  47 osmini                                          [0x00]

Rx: 09:06:32  <Standby>                   <  36 

Tx: 09:07:32  <Image View On>             >  04                                                 [0x00]

Rx: 09:07:32  <Give Device Vendor ID>     <  8C 

Tx: 09:07:32  <Device Vendor ID>          >  87 00 00 00                                        [0x00]

Rx: 09:07:33  <Feature Abort>             <  00 87 00 

Rx: 09:07:33  <Give OSD Name>             <  46 

Tx: 09:07:33  <Set OSD Name>              >  47 osmini                                          [0x00]

Tx: 09:10:10  <Inactive Source>           >  9D 40 00                                           [0x00]

Rx: 09:10:10  <Feature Abort>             <  00 9D 04 

Rx: 09:11:47  <Standby>                   <  36 

Tx: 09:11:49  <Image View On>             >  04                                                 [0x00]

Tx: 09:18:13  <Standby>                   >  36                                                 [0x00]

Rx: 09:18:14  <Standby>                   <  36 

[ims]

I cannot know from this debug, where you press standby and whre wake up...

 

But what is wrong is, that box sending 36 = standby , both your devices (are connected next 2 hdmi devices) send back "Standby" too and then send back info, that are online...

 

 

Try use HDMITest plugin and send manualy "standby" to HDMI-CEC and see, what happens

 

Do you want use Standby or Deep standby on box ?

[Drago]

a single HDMI device is connected to the TV

[ims]

a single HDMI device is connected to the TV

Then is weird, that tv answers twice

[Drago]

good morning

what to think?

with other firmware this does not happen

I always have the same TV with the same cable and the same decoder

that's why I was trying to compare the two hdmi-cec plugins, just to find the differences and understand what's not working

unfortunately my skills and knowledge of firmware in general are limited and alone I can't manage them.

[Drago]

the forum does not let me edit the post (a second after inserting it) so I continue to write, excuse the posts in sequence

 

as for the shutdown I use standby, that is I switch off only from the remote control, in fact as soon as I switch it on the decoder immediately responds with channel vision, turns on the TV and is tt ok, the problem remains at shutdown only the decoder goes off while the TV remains on.

 

try this morning log clean

 

Tx: 07:31:59  <Image View On>             >  04                                                 [0x00]

Rx: 07:31:59  <Give Device Vendor ID>     <  8C 

Tx: 07:31:59  <Device Vendor ID>          >  87 00 00 00                                        [0x00]

Rx: 07:32:00  <Feature Abort>             <  00 87 00 

Rx: 07:32:01  <Give OSD Name>             <  46 

Tx: 07:32:01  <Set OSD Name>              >  47 osmini                                          [0x00]

Tx: 07:57:07  <Inactive Source>           >  9D 40 00                                           [0x00]

Rx: 07:57:07  <Feature Abort>             <  00 9D 04 

 

 

I did the tests with hdmi test and everything works, but I don't know where to take the log to insert it here on the forum

Edited by Drago, 11 April 2019 - 06:59.

[ims]

If HDMI Test and "Standby" works, then must works Standby from PLi too. HDMI-Test is PLi's plugin using same CEC features.

 

Do you have installed some special plugin oe skin your box ? Image version ?

[ims]

I am confused what you are trying...

 

1) you wake-up box and box 7:31 with sending 04 ... ok

 

but why do you sending on 7:57 <Inactive Source>  ??? It was toggle box to Standby ?

 

 

 

[ims]

Could you try put this .py file to /usr/lib/enigma2/python/Components/ directory and restart GUI ?

 

Btw - your TV producer is ?

Attached Files

•  HdmiCec.py   17.73KB   4 downloads

[Drago]

197/5000

 

 

 

to make the tests I turned on the decoder at 7:31 and then I tried to turn it off at 7:52 the one above the operation log needless to reiterate that the TV remained on

the TV brand is Toshiba

I inserted your .py file .......................... I do the tests

[Drago]

Hi IMS

 

your file modification seems to work

 

if config.hdmicec.enabled.value and config.hdmicec.handle_deepstandby_events.value:

 

if config.hdmicec.next_boxes_detect.value:

 

from the tests carried out last night and this morning, I found, finally, the TV shutdown

 

thanks to you I am glad I solved it

[ims]

Seems, main problem is in your TV ... Device can report power status on demand only and not after receiving stanby request ...

I will add fix to 7.0.