202 replies to this topic

[Frenske]

I hope this mini Movie works. https://we.tl/b-d75hTzXrUD

[tappari]

I have 2 x BMC3466 and 1 x TT3L10 tuners in my Ultimo 4K. All 6 tuners are configured as T2. With VU+  drivers 2019.04.24 box jams after fullboot.

Same happens with OpenViX 5.2 040 and OpenATV 6.3 with those drivers. 

Edited by tappari, 16 May 2019 - 11:05.

[tappari]

If I disable tuners E and F from TT3L10 dualtuner then ok. I think new drivers from Marusys needed. 

Open PLi 7.0 works fine with all 6 tuners as T2.

Edited by tappari, 16 May 2019 - 12:12.

[niksiz]

Testing in Vu+ Duo 4K. 

 

+ Multistram seems to be working. Tested on HellasSat, 12593V.

- Clock is back for about five minutes. How to fix it?

- Weather plugin does not work. After adding a city and try to update it gives: syntax error: line 1, column 0

[WanWizard]

- Clock is back for about five minutes. How to fix it?

 

Enigma refuses to change the time when it deviates too much, which is an issue if you start up with the wrong time.

 

Set your box to a channel of a known good transponder. Put the box in deep standby, and switch the box off or disconnect the power so the internal clock stops. Wait a bit, and start the box up again.

 

It's a known issue not related to OpenPLi or this version. We're looking into dealing with this for OpenPLi 8.

 

- Weather plugin does not work. After adding a city and try to update it gives: syntax error: line 1, column 0

 

You have to report that to the author of that plugin, we don't make it. With a bit of luck, she/he reads this.

[niksiz]

 

- Clock is back for about five minutes. How to fix it?

 

Enigma refuses to change the time when it deviates too much, which is an issue if you start up with the wrong time.

 

Set your box to a channel of a known good transponder. Put the box in deep standby, and switch the box off or disconnect the power so the internal clock stops. Wait a bit, and start the box up again.

 

It's a known issue not related to OpenPLi or this version. We're looking into dealing with this for OpenPLi 8.

 

This solved the problem.

 

- Weather plugin does not work. After adding a city and try to update it gives: syntax error: line 1, column 0

 

You have to report that to the author of that plugin, we don't make it. With a bit of luck, she/he reads this.

 

 

[Stosun]

Hi, it already contains 7.1 chromium and youtube TV versions? Thanks

[Taykun345]

Today I flashed 7.1RC from FLASH MENU (works great btw with autobackup). Will see now if I can notice any positive change.

[Aliraza63]

Open Pli 7.1 Tested at my  :

Solo2  (working fine )

Uno4k Se ( (16Gb ssd installed) Have an issue to make backup from backsuit . It restarts it self

Zgemmma H9twin ( backup suit errore same as I have in VU+uno4kse)

[littlesat]

New multiboot system in h9 is indeed most likely not compatible with backupsuite

[WanWizard]

Hi, it already contains 7.1 chromium and youtube TV versions? Thanks

 

No. The last time I checked they still crashed, and VU+ hasn't done anything about it. It is still disabled in their BSP.

[nor50]

Installed on Solo 4K. Softcam didn't work from backup, but installed from menu. Just started testing. All well so far.

Edited by nor50, 18 May 2019 - 16:10.

[Taykun345]

In my case softcam recovered just fine. No problems.

[niksiz]

There is a problem with motorised dish. Sometimes the positioner did not go to desired satellite (it happens for all configured sattelites). For example when I zap from 0.8W to 4.8E the dish does not move (dish move animation appears and counts). Then I try a channel from 13E and it goes. Back to 4.8E does not work. Only solution I found right now is go to signal finder, lock to a transponder and scan it. In addition locking to a transponder takes about two three seconds. I say this because I did not face it previously on Vu+ Duo.

Edited by niksiz, 18 May 2019 - 21:41.

[majidnourollahi]

is .webm file playback solved in this version??

[centurius]

I'm trying 7.1 on edision os mio 4k, but the kernel is 5.0 will also be on openpli 5.1

[Posi]

If you go to Menu>Setup>System>Audio/Video>Auto language selection>EPG language selection 1. There is no Finnish available as in EPG language selection 2.

[Frenske]

@Posi,

Can confirm this and will report it to the developers.

[littlesat]

Mmmm I cannot confirm it.... I have Finnish available as first EPG language... But it will not be available when the first language is already Finnish...

 1_0_19_4BC9_832_600_FFFF0000_0_0_0_20190520174141.jpg   85.63KB   10 downloads

Edited by littlesat, 20 May 2019 - 16:42.

[Frenske]

Mmmm I cannot confirm it.... I have Finnish available as first EPG language... But it will not be available when the first language is already Finnish...
1_0_19_4BC9_832_600_FFFF0000_0_0_0_20190520174141.jpg

You’re completely right. As first language I was looking for Finnish and, after having noticed that Finnish was present as first language, left Finnish as the first choosen language. And in that case it makes sense that Finnish can’t be choosen as secondary language.