Posted 16 May 2019 - 12:56
Hi to all on here,
Hoping someone can help, I bought Zgemma H9S box over a month ago and from day one have been using your images I have Openpli Release 7.0 2019/05/06 and went to turn my box off and it would so i turned off at rear and back on again only to find that box does not boot up fully i have screen on tv stuck with Openpli Release page in red and white etc any advice or help would be most grateful ??
Many Thanks
charlie69
Posted 16 May 2019 - 13:06
If you see that screen the box has booted succesfully.
If it doesn't continue, either enigma crashes on startup, or you don't have a valid startup channel configured, so it stays there because it can't switch to a tune into a channel and show it. If that is the case, it should still respond to the remote.
If enigma crashes, you need to login via telnet, type the command "dmesg", check for errors and post those there so we can have a look.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 16 May 2019 - 15:13
using dreambox control center lots has come up when using telnet what should i be looking for ??
Posted 16 May 2019 - 15:18
looked all the way through and not once have i seen error for anything ??
Posted 16 May 2019 - 15:37
If you type the command
ps | grep enigma
do you get something like
1603 root 2776 S {enigma2.sh} /bin/sh /usr/bin/enigma2.sh
1612 root 405m S /usr/bin/enigma2
2462 root 2576 S grep enigma
?
If so, enigma is running fine and you have a configuration issue. The remote should work fine too.
If not, you could also check the error message log, using
cat /var/log/messages
and look for errors.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 16 May 2019 - 22:18
Try with openwebif http://ip-address from your box
You see there a remote on the left, try this out to see if anything is reacting. Maybe your remote is damaged in some way.
Mut@nt HD51 STB 4K
Posted 17 May 2019 - 11:13
I have typed ps | grep enigma I got 1 line back
also tried cat /var/log/messages and lots of writing no errors but i saw alot of lines saying respawnimg too fast disabled for 5 mins
Posted 17 May 2019 - 11:14
Try with openwebif http://ip-address from your box
You see there a remote on the left, try this out to see if anything is reacting. Maybe your remote is damaged in some way.
I try this it does not let me open webif
Posted 17 May 2019 - 12:28
Have you tried reflashing the box ?
Posted 17 May 2019 - 12:35
I have typed ps | grep enigma I got 1 line back
also tried cat /var/log/messages and lots of writing no errors but i saw alot of lines saying respawnimg too fast disabled for 5 mins
Good. That means we have now established that enigma crashes.
Next, type in this command:
ENIGMA_DEBUG_LVL=4 enigma2
it will write it's debug output to the console. Capture the output, and post it here (in a code block or as an attached .log file) so we can see why it crashes.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 20 May 2019 - 10:22
I have typed ps | grep enigma I got 1 line back
also tried cat /var/log/messages and lots of writing no errors but i saw alot of lines saying respawnimg too fast disabled for 5 mins
Good. That means we have now established that enigma crashes.
Next, type in this command:
ENIGMA_DEBUG_LVL=4 enigma2it will write it's debug output to the console. Capture the output, and post it here (in a code block or as an attached .log file) so we can see why it crashes.
Thank you for all your great advice but ended up doing a re flash its working now but going to start a new thread as i have more trouble with image im afriad lol thanks to you all its much appreciated Thank you
Posted 27 July 2020 - 16:21
* Xtrend ET-4000 + XSarius Fusion HD * SAB 10/1 switch met 28.2E/23.5E/19.2E/16E/13E/9E/7E/4.8E/0.8W/5W (niet actief)
* Maximum E85 schotel met 3 Multifeed Megasat, 2 Inverto Black Ultra en 4 Inverto Multiconnect (niet actief) *SAB 97cm met Moteck SG2100A en Inverto Black Ultra
Posted 27 July 2020 - 21:55
Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.
Dreamboxen heb ik niet meer echt actief. Verder heb ik ook nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET7x00. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. 
Los van de eerder genoemde modellen heb ik nog wel een rits aan testsamples als Mut@nt 2400HD, HD60, GB UE4K, GB Trio4K, Maxitec Multibox combo en Twin, Octagon sf8008, sf8008 mini en last but nog least enkele modellen van het Grieks Duitse Edision.
Voor centrale opslag van media gebruik ik een Qnap 219P met tweemaal 2 Tb harddisks + een Synology DS414 met 12 Tb Totale opslag.
-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".
Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.
0 members, 1 guests, 0 anonymous users
