Jump to content


Photo

Lunix3 4K with 7.1 does not read nagra cards


  • Please log in to reply
29 replies to this topic

#1 satspace

  • Member
  • 14 posts

0
Neutral

Posted 26 August 2019 - 11:13

Hi,

I have a Qviart Lunix3 4k stb and using opnpli7.0 with no problem,

After updating to 7.1 (any version) the nagra smartcard (tivusat) is no longer read (neither with CCCam nor OScam) in internal reader.

I also tried to reflash a clean 7.1 inmage but things remain the same...

 

The card is working fine with other receivers and with OPLI 7.0

 

Any suggestion ?

 

Thanks!!

 

 



Re: Lunix3 4K with 7.1 does not read nagra cards #2 satspace

  • Member
  • 14 posts

0
Neutral

Posted 26 August 2019 - 11:27

Forgot to mention that softcams are installed via plugin gui, so default config... (works with 7.0 the same way).



Re: Lunix3 4K with 7.1 does not read nagra cards #3 mimisiku

  • Senior Member
  • 2,153 posts

+28
Good

Posted 26 August 2019 - 11:46

OpenPli does nothing with the decoding! Decoding is handled by the softcam or CI... Since OpenPli does not handle CI+, you will need a softcam for your card. You can however check if the internal reader works. It has happened before that due to a building fault a module was blanked out...
VU+ Solo SE v2 Optus NZ

Re: Lunix3 4K with 7.1 does not read nagra cards #4 satspace

  • Member
  • 14 posts

0
Neutral

Posted 26 August 2019 - 11:54

OpenPli does nothing with the decoding! Decoding is handled by the softcam or CI... Since OpenPli does not handle CI+, you will need a softcam for your card. You can however check if the internal reader works. It has happened before that due to a building fault a module was blanked out...

Hi,

as mentioned above, with openpli 7.0 everithing is ok.

the issue is with 7.1

 

So the hardware works (reader and card), and the softcam is the same with same default settings.

The only difference is the pli version, as mentioned...

 

So, what to check exactly ??

thanks



Re: Lunix3 4K with 7.1 does not read nagra cards #5 mimisiku

  • Senior Member
  • 2,153 posts

+28
Good

Posted 26 August 2019 - 12:16

Check if the interal reader actually works in OpenPli 7.1... Eventually with another type of card (may be expired)
VU+ Solo SE v2 Optus NZ

Re: Lunix3 4K with 7.1 does not read nagra cards #6 satspace

  • Member
  • 14 posts

0
Neutral

Posted 26 August 2019 - 12:36

Check if the interal reader actually works in OpenPli 7.1... Eventually with another type of card (may be expired)

No it does not work,

gives error in getting card information also with older expired cards ....



Re: Lunix3 4K with 7.1 does not read nagra cards #7 Frenske

  • Forum Moderator
    PLi® Core member
  • 22,177 posts

+200
Excellent

Posted 26 August 2019 - 13:25

Did you check both CCcam and Oscam?
Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.

Dreamboxen heb ik niet meer. Verder nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET4000. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. ;) :)

Voor centrale opslag van media gebruik ik een Qnap 219P met tweemaal 2 Tb harddisks.

-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".

Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.

Re: Lunix3 4K with 7.1 does not read nagra cards #8 satspace

  • Member
  • 14 posts

0
Neutral

Posted 26 August 2019 - 13:36

Did you check both CCcam and Oscam?

Yes, read first post...

:-) and now my post restriction policy applies... so please would you please approve my previous replies ?

thanks



Re: Lunix3 4K with 7.1 does not read nagra cards #9 Frenske

  • Forum Moderator
    PLi® Core member
  • 22,177 posts

+200
Excellent

Posted 26 August 2019 - 13:48

I didn’t notice that detail in the first posting.
I see no other postings in this topic that needs approvement. It might be due to the fact that new member has some limitations / day. I’ll ask the webmaster.
Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.

Dreamboxen heb ik niet meer. Verder nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET4000. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. ;) :)

Voor centrale opslag van media gebruik ik een Qnap 219P met tweemaal 2 Tb harddisks.

-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".

Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.

Re: Lunix3 4K with 7.1 does not read nagra cards #10 WanWizard

  • Forum Moderator
    PLi® Core member
  • 48,469 posts

+824
Excellent

Posted 26 August 2019 - 14:43

As said, OpenPLi does nothing with a card or cardreader, there could only be a few causes:

  • Hardware fault with the reader (ruled out as 7.0 seems to work fine)
  • Hardware fault with the card (ruled out as 7.0 seems to work fine)
  • Driver issue (7.1 has different hardware drivers from 7.0)
  • Softcam issue (7.1 has a newer/different Oscam, but CCcam is the same in both releases)

Currently in use: VU+Duo 4K (2xFBC S2), Amiko Viper T2C (T2), SAB Alpha Triple HD (S2+T2), Zgemma H3.T2C (T/C), Zgemma H6 (fallback), VU+Zero (fallback)

Many answers to your question can be found in our new and improved wiki.

note: I do not provide support via PM !

 


Re: Lunix3 4K with 7.1 does not read nagra cards #11 littlesat

  • PLi® Core member
  • 49,224 posts

+527
Excellent

Posted 26 August 2019 - 14:49

Or your RSA pairing key is not in the config?


WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W


Re: Lunix3 4K with 7.1 does not read nagra cards #12 anudanan

  • Senior Member
  • 998 posts

+14
Neutral

Posted 26 August 2019 - 15:00

I´m a little bit confused. From my knowledge if a user will use a card insaide the Ci modul, then there is no need for a softcam like oscam or cccam. Isn´t it?


Edited by anudanan, 26 August 2019 - 15:00.

Receiver:2 x Uno4k SE (PLI 7.0 rel), 1 x ET9200 (PLI 4.0), NAS: 2 x QNAP 410, TV: LG 65C8llla, LG 47LB570V, LG 42LM615S, Sound: Yamaha RX-v663, Teufel System 5 THX

Re: Lunix3 4K with 7.1 does not read nagra cards #13 mimisiku

  • Senior Member
  • 2,153 posts

+28
Good

Posted 26 August 2019 - 15:09

He can't use a CI+ as OpenPli doesn't support these. I don't know if his Nagra card should use a CI+ by default or can still run in a normal CI...
VU+ Solo SE v2 Optus NZ

Re: Lunix3 4K with 7.1 does not read nagra cards #14 WanWizard

  • Forum Moderator
    PLi® Core member
  • 48,469 posts

+824
Excellent

Posted 26 August 2019 - 15:41

The OP says "in an internal reader". Nobody is talking about a module.


Currently in use: VU+Duo 4K (2xFBC S2), Amiko Viper T2C (T2), SAB Alpha Triple HD (S2+T2), Zgemma H3.T2C (T/C), Zgemma H6 (fallback), VU+Zero (fallback)

Many answers to your question can be found in our new and improved wiki.

note: I do not provide support via PM !

 


Re: Lunix3 4K with 7.1 does not read nagra cards #15 satspace

  • Member
  • 14 posts

0
Neutral

Posted 26 August 2019 - 15:58

 

As said, OpenPLi does nothing with a card or cardreader, there could only be a few causes:

  • Hardware fault with the reader (ruled out as 7.0 seems to work fine)
  • Hardware fault with the card (ruled out as 7.0 seems to work fine)
  • Driver issue (7.1 has different hardware drivers from 7.0)
  • Softcam issue (7.1 has a newer/different Oscam, but CCcam is the same in both releases)

 

Ok, so following your exclusion list and my test the only cause would be the third: Driver issue...

Then , how can I step on further  with the resolution ?

 

Thanks



Re: Lunix3 4K with 7.1 does not read nagra cards #16 Frenske

  • Forum Moderator
    PLi® Core member
  • 22,177 posts

+200
Excellent

Posted 26 August 2019 - 15:58

:-) and now my post restriction policy applies... so please would you please approve my previous replies ?
thanks

I’ve been informed that you still can post.
Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.

Dreamboxen heb ik niet meer. Verder nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET4000. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. ;) :)

Voor centrale opslag van media gebruik ik een Qnap 219P met tweemaal 2 Tb harddisks.

-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".

Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.

Re: Lunix3 4K with 7.1 does not read nagra cards #17 satspace

  • Member
  • 14 posts

0
Neutral

Posted 26 August 2019 - 16:01

 

:-) and now my post restriction policy applies... so please would you please approve my previous replies ?
thanks

I’ve been informed that you still can post.

 

Yess, thanks!



Re: Lunix3 4K with 7.1 does not read nagra cards #18 Pr2

  • PLi® Contributor
  • 3,648 posts

+156
Excellent

Posted 28 August 2019 - 10:09

Hi,

 

Check in your softcam the card MHz parameter that's often what prevent the card from properly initialize.

 

Pr2


NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.

Wanna help with OpenPLi Translation? Please read our Wiki Information for translators

Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
 


Re: Lunix3 4K with 7.1 does not read nagra cards #19 satspace

  • Member
  • 14 posts

0
Neutral

Posted 28 August 2019 - 10:56

Hi,

 

Check in your softcam the card MHz parameter that's often what prevent the card from properly initialize.

 

Pr2

As mentioned above, the config files are not customized; the default are used in both 7.0 and 7.1 with same version of softcam.



Re: Lunix3 4K with 7.1 does not read nagra cards #20 satspace

  • Member
  • 14 posts

0
Neutral

Posted 28 August 2019 - 10:58

 

 

As said, OpenPLi does nothing with a card or cardreader, there could only be a few causes:

  • Hardware fault with the reader (ruled out as 7.0 seems to work fine)
  • Hardware fault with the card (ruled out as 7.0 seems to work fine)
  • Driver issue (7.1 has different hardware drivers from 7.0)
  • Softcam issue (7.1 has a newer/different Oscam, but CCcam is the same in both releases)

 

Ok, so following your exclusion list and my test the only cause would be the third: Driver issue...

Then , how can I step on further  with the resolution ?

 

Thanks

 

@WanWizard: do you have any news for me regarding details of your suggestion ?

 

AKA: Can I use internal card reader driver from pli 7.0 in 7.1 ? how ?  (i am not scared of using unix shell....:-)

 

 

thanks


Edited by satspace, 28 August 2019 - 11:00.





0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users