Jump to content


Photo

OpenPLi Release Candidate 7.2


  • Please log in to reply
195 replies to this topic

Re: OpenPLi Release Candidate 7.2 #121 Pike_Bishop

  • Senior Member
  • 887 posts

+33
Good

Posted 15 October 2019 - 22:46

i hope i have nor a bit time before the release is coming, i want make the de translations for vu bluetooth setup plugin.

 

 

regards

Pike


Receiver: Mutant HD 2400, VU Ultimo 4k

Image: PLI 7.1


Re: OpenPLi Release Candidate 7.2 #122 dudule22

  • Senior Member
  • 60 posts

0
Neutral

Posted 17 October 2019 - 12:24

Little bugs persists on VU+ DUO 4k

 

Video settings are lost,sometime and the the screen is a lttle bit bad resized. It works fine after a reboot.

Only 2160p 30 Hz works on VU+ DUO 4 K (for 2160 mode).

 

Crasy songs also appears sometimeon tnt channels and it works fine after a reboot.



Re: OpenPLi Release Candidate 7.2 #123 FRAP

  • Senior Member
  • 175 posts

+7
Neutral

Posted 21 October 2019 - 07:36

Hello! The release version is still being tested. Please add the Lcd4linux plugin with the new version 5.0r5.
This is information from the Author of the plugin (its corrections, additions)
 
Lcd4linux 5.0r5

- kleines Updaterollup
- Tuner 2zeilig

CONFUCIUS: Only a fool in his life does not change his mind.


Re: OpenPLi Release Candidate 7.2 #124 isteric2005

  • Senior Member
  • 173 posts

+1
Neutral

Posted 31 October 2019 - 14:20

I updated online today and I get this error on zgemma h9h

 

Attached Files



Re: OpenPLi Release Candidate 7.2 #125 Frenske

  • Forum Moderator
    PLi® Core member
  • 22,439 posts

+202
Excellent

Posted 31 October 2019 - 14:30

I notice these kind of reports too once in a while and they don’t really bother me. It might be caused by that specific plugin. You might try to uninstall / install the plugin again. 


Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.

Dreamboxen heb ik niet meer. Verder nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET4000. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. ;) :)

Voor centrale opslag van media gebruik ik een Qnap 219P met tweemaal 2 Tb harddisks.

-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".

Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.

Re: OpenPLi Release Candidate 7.2 #126 WanWizard

  • Forum Moderator
    PLi® Core member
  • 49,021 posts

+841
Excellent

Posted 31 October 2019 - 14:42

Found the issue, fixed in tomorrow's build.


Currently in use: VU+Duo 4K (2xFBC S2), Amiko Viper T2C (T2), SAB Alpha Triple HD (S2+T2), Zgemma H3.T2C (T/C), Zgemma H6 (fallback), VU+Zero (fallback)

Many answers to your question can be found in our new and improved wiki.

note: I do not provide support via PM !

 


Re: OpenPLi Release Candidate 7.2 #127 isteric2005

  • Senior Member
  • 173 posts

+1
Neutral

Posted 31 October 2019 - 14:59

I notice these kind of reports too once in a while and they don’t really bother me. It might be caused by that specific plugin. You might try to uninstall / install the plugin again. 

Already tried .... but the same result

 

Found the issue, fixed in tomorrow's build.

Thanks



Re: OpenPLi Release Candidate 7.2 #128 Florie

  • Senior Member
  • 41 posts

0
Neutral

Posted 31 October 2019 - 17:38

 

 

I actually do not understand the option in "fallback tuner" which says "customize openwebif". What is it supposed to do?  :)

 

If you don't know what it is, you don't need it. ;) It's for some non-standard webif installations (fallback uses the WebIf API to communicate with the server box).

 

I have a main box (vu duo4k) and a client box (vu zero), both on the latest 7.2rc. When I open the timer menu on the client box, every entry has one (and the same) directory. However on the main box the times have different directories.

 

There is no real-time connection between client and server.

 

Afaik the client retrieves the list of bookmark locations from the server box (movielist, yellow button) and uses those as possible locations for a remote timer.

 

 

ok fair enough, but why does the client box just show the last bookmark of the main box on every existing timer (even if another bookmark was set on the main box) and chooses this last (main box) bookmark as primary location on new timers set by the client box. I would say for me (my bookmarks are identical on both boxes) it would be logical if the client box sets the location from the setup (client box default movie location).

 

Any news? This still persists.



Re: OpenPLi Release Candidate 7.2 #129 isteric2005

  • Senior Member
  • 173 posts

+1
Neutral

Posted 1 November 2019 - 10:51

Found the issue, fixed in tomorrow's build.

The update 5 packages of today the problem still exists



Re: OpenPLi Release Candidate 7.2 #130 Frenske

  • Forum Moderator
    PLi® Core member
  • 22,439 posts

+202
Excellent

Posted 1 November 2019 - 10:57

 

Found the issue, fixed in tomorrow's build.

The update 5 packages of today the problem still exists

 

The RC update is only available from about 16:00h. 


Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.

Dreamboxen heb ik niet meer. Verder nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET4000. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. ;) :)

Voor centrale opslag van media gebruik ik een Qnap 219P met tweemaal 2 Tb harddisks.

-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".

Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.

Re: OpenPLi Release Candidate 7.2 #131 isteric2005

  • Senior Member
  • 173 posts

+1
Neutral

Posted 1 November 2019 - 13:34

 

 

Found the issue, fixed in tomorrow's build.

The update 5 packages of today the problem still exists

 

The RC update is only available from about 16:00h. 

 

Tkanks



Re: OpenPLi Release Candidate 7.2 #132 ciciol

  • Senior Member
  • 97 posts

+3
Neutral

Posted 2 November 2019 - 09:26

Hello, On VU + UNO 4K SE, when switching programs, the message "Tuning failed" appears quite often and after 3-4 seconds the message disappears and the program is shown in a moment. The tuner has been tested on 4 different installations and various configurations. A friend on another system does not have this problem

Re: OpenPLi Release Candidate 7.2 #133 betacentauri

  • PLi® Core member
  • 5,545 posts

+252
Excellent

Posted 2 November 2019 - 09:32

You have most likely installed the lcd4linux plugin. Please deinstall and reboot.


Xtrend ET-9200, ET-8000, ET-10000, OpenPliPC on Ubuntu 12.04

Re: OpenPLi Release Candidate 7.2 #134 ciciol

  • Senior Member
  • 97 posts

+3
Neutral

Posted 2 November 2019 - 10:38

Approx. I'll be home on Sunday, I'll check it out. But why this plugin can have such a meaning? Although on a clean system as far as I remember it was exactly the same. best regards

Edited by ciciol, 2 November 2019 - 10:41.


Re: OpenPLi Release Candidate 7.2 #135 isteric2005

  • Senior Member
  • 173 posts

+1
Neutral

Posted 2 November 2019 - 10:50

Today it updates 63 packages;
_ epg import works again
_ hdmi check no longer works
_ no channel visible on the dtt (black screen)
zgemma h9h decoder



Re: OpenPLi Release Candidate 7.2 #136 betacentauri

  • PLi® Core member
  • 5,545 posts

+252
Excellent

Posted 2 November 2019 - 10:53

Approx. I'll be home on Sunday, I'll check it out. But why this plugin can have such a meaning? Although on a clean system as far as I remember it was exactly the same. best regards

 

Here is one thread regarding the problem. We don't know why it happens:

https://forums.openp...4k-tune-failed/


Xtrend ET-9200, ET-8000, ET-10000, OpenPliPC on Ubuntu 12.04

Re: OpenPLi Release Candidate 7.2 #137 tomek

  • Senior Member
  • 59 posts

+3
Neutral

Posted 2 November 2019 - 10:55

Today it updates 63 packages;
_ epg import works again
_ hdmi check no longer works
_ no channel visible on the dtt (black screen)
zgemma h9h decoder

 

Same here black screen on dvb-s/c/t/webstreams. Thats probably due to bsp layer update: https://github.com/O...6fb3905e1a6ea63

Reflash from the menu again to 1.11 rc - it will work again. Update is broken.



Re: OpenPLi Release Candidate 7.2 #138 littlesat

  • PLi® Core member
  • 49,554 posts

+533
Excellent

Posted 2 November 2019 - 11:00

With rc it can indeed be that you need to reflash

WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W


Re: OpenPLi Release Candidate 7.2 #139 isteric2005

  • Senior Member
  • 173 posts

+1
Neutral

Posted 2 November 2019 - 11:21

 

Today it updates 63 packages;
_ epg import works again
_ hdmi check no longer works
_ no channel visible on the dtt (black screen)
zgemma h9h decoder

 

Same here black screen on dvb-s/c/t/webstreams. Thats probably due to bsp layer update: https://github.com/O...6fb3905e1a6ea63

Reflash from the menu again to 1.11 rc - it will work again. Update is broken.

 

 

 

With rc it can indeed be that you need to reflash

I confirm that the execution of the reflash has returned to normal



Re: OpenPLi Release Candidate 7.2 #140 ciciol

  • Senior Member
  • 97 posts

+3
Neutral

Posted 2 November 2019 - 11:23


Approx. I'll be home on Sunday, I'll check it out. But why this plugin can have such a meaning? Although on a clean system as far as I remember it was exactly the same. best regards


Here is one thread regarding the problem. We don't know why it happens:
https://forums.openp...4k-tune-failed/
Thank you




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users