Open the web interface, and press on the phone icon in front of a channel. Does a transcoded stream start?
I did exactly as you suggested. Unfortunately, I didn't get the transcoded stream. What should I change? 
Openpli 8.2
Started by jocke90s, 04 May 2022 13:13
69 replies to this topic
Re: Openpli 8.2 #41
-
- Member
- 9 posts
0
Neutral
Posted 23 May 2022 - 15:57
Re: Openpli 8.2 #42
-
- PLi® Core member
- 70,476 posts
+1,809
Excellent
Posted 23 May 2022 - 16:29
What port is used in the link that you get when you click that icon? 8001 bij any chance?
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: Openpli 8.2 #43
-
- Member
- 9 posts
0
Neutral
Posted 23 May 2022 - 16:44
http://-sid:73baccea...192.168.178.49:8002/1:0:16:76:4B0:110:820000:0:0:0:?bitrate=1000000&width=1280&height=720&aspectratio=2&interlaced=0
Re: Openpli 8.2 #44
-
- Guest
- 396 posts
+2
Neutral
Posted 23 May 2022 - 18:37
Open the web interface, and press on the phone icon in front of a channel. Does a transcoded stream start?
Is a file .m3u8?
Re: Openpli 8.2 #45
-
- PLi® Core member
- 70,476 posts
+1,809
Excellent
Posted 23 May 2022 - 23:05
http://-sid:73baccea...192.168.178.49:8002/1:0:16:76:4B0:110:820000:0:0:0:?bitrate=1000000&width=1280&height=720&aspectratio=2&interlaced=0
Plays fine here, but without the password protected session id... So I assume the issue is in there somewhere.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: Openpli 8.2 #46
-
- Member
- 9 posts
0
Neutral
Posted 24 May 2022 - 04:36
I can't disable authentication for stream. Nothing else comes to mind. There are not many options to change here, especially in version 8.2. I have to go back to 8.1. Thank you for your support.
Re: Openpli 8.2 #47
-
- Senior Member
- 121 posts
+7
Neutral
Posted 24 May 2022 - 08:07
Same on Ultimo 4K. The transcoding doesn't work. Normal stream on port 8001 has no problems.
VU+ Ultimo 4K; Clarke-Tech et9000
Re: Openpli 8.2 #48
-
- PLi® Core member
- 13,781 posts
+214
Excellent
Posted 24 May 2022 - 09:25
Tried on Duo4k now - no problem stream on 8001 (Owif - stream) and 8002 (Owif - stream - transcoded).
Kdo nic nedělá, nic nezkazí!
Re: Openpli 8.2 #49
-
- Forum Moderator
PLi® Core member - 27,493 posts
+397
Excellent
Posted 24 May 2022 - 10:03
Same on Ultimo 4K. The transcoding doesn't work. Normal stream on port 8001 has no problems.
Just checked my Ultimo 4K. After having changed the transcoding settings it might be needed to restart the box.
Via OWIF transcoding works as I am used to.
Attached Files
-
B0D6536A-B416-4685-B683-DA9097A80802.jpeg 75.03KB
4 downloads
Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.
Dreamboxen heb ik niet meer echt actief. Verder heb ik ook nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET7x00. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. 
Los van de eerder genoemde modellen heb ik nog wel een rits aan testsamples als Mut@nt 2400HD, HD60, GB UE4K, GB Trio4K, Maxitec Multibox combo en Twin, Octagon sf8008, sf8008 mini en last but nog least enkele modellen van het Grieks Duitse Edision.
Voor centrale opslag van media gebruik ik een Qnap 219P met tweemaal 2 Tb harddisks + een Synology DS414 met 12 Tb Totale opslag.
-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".
Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.
Re: Openpli 8.2 #50
-
- Senior Member
- 121 posts
+7
Neutral
Posted 24 May 2022 - 11:33
Same on Ultimo 4K. The transcoding doesn't work. Normal stream on port 8001 has no problems.
After having changed the transcoding settings it might be needed to restart the box.
Restart did the trick. Now it's working .Thanks!
VU+ Ultimo 4K; Clarke-Tech et9000
Re: Openpli 8.2 #51
-
- Guest
- 396 posts
+2
Neutral
Posted 24 May 2022 - 12:40
Open the web interface, and press on the phone icon in front of a channel. Does a transcoded stream start?
Is a file .m3u8?
Obviously I didn't understand or maybe it's something I don't use.
What are you talking about.
Thanks.
Re: Openpli 8.2 #52
-
- Member
- 9 posts
0
Neutral
Posted 24 May 2022 - 19:35
Same on Ultimo 4K. The transcoding doesn't work. Normal stream on port 8001 has no problems.
Just checked my Ultimo 4K. After having changed the transcoding settings it might be needed to restart the box.
Via OWIF transcoding works as I am used to.
In fact, restarting the box helped with transcoding. Thanks so much, guys.
Re: Openpli 8.2 #53
-
- PLi® Core member
- 70,476 posts
+1,809
Excellent
Posted 24 May 2022 - 19:53
You're working around the problem using the old streamproxy, That only works on VU+ 4K boxes, not on all other that also support transcoding.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: Openpli 8.2 #54
-
- Guest
- 396 posts
+2
Neutral
Posted 24 May 2022 - 22:15
Ok, I documented but it doesn't interest me. Sorry for the intrusion.
Obviously I didn't understand or maybe it's something I don't use.
Is a file .m3u8?
Open the web interface, and press on the phone icon in front of a channel. Does a transcoded stream start?
What are you talking about.
Thanks.
Re: Openpli 8.2 #55
-
- Senior Member
- 184 posts
+120
Excellent
Posted 25 May 2022 - 17:32
USB drivers cannot be installed on the ABPULSe 4k receiver.
Attached Files
-
usbserial.jpg 89.91KB
4 downloads
Re: Openpli 8.2 #56
-
- PLi® Core member
- 70,476 posts
+1,809
Excellent
Posted 25 May 2022 - 20:09
That is a kernel driver, which means it is most likely not enabled in the manufactuers kernel config. You get that when you want to install serial drtivers I assume?
edit: nope, not enabled: https://github.com/C...defconfig#L3306
edit: Asked abcom to update it: https://github.com/C...-pulse4k/pull/7
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: Openpli 8.2 #57
-
- Senior Member
- 121 posts
+7
Neutral
Posted 26 May 2022 - 07:06
Just installed and tried Webkithbbtv. It is now working, except for playing videos. Perhaps is not fully installed, as on some channels together with RED button it shows "Missing Plug-in". On ARTE when trying to watch Concert for example, it is showing "Loading in progress..." and video doesn't start.
VU+ Ultimo 4K; Clarke-Tech et9000
Re: Openpli 8.2 #58
-
- Forum Moderator
PLi® Core member - 27,493 posts
+397
Excellent
Posted 26 May 2022 - 07:43
On Vu+ hardware HBBTV has hardly ever worked. VU+ seems not to be be interested in putting any effort to adapt their WebKit. AFAIK it didn’t work either on any previous versions.
Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.
Dreamboxen heb ik niet meer echt actief. Verder heb ik ook nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET7x00. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen.
Los van de eerder genoemde modellen heb ik nog wel een rits aan testsamples als Mut@nt 2400HD, HD60, GB UE4K, GB Trio4K, Maxitec Multibox combo en Twin, Octagon sf8008, sf8008 mini en last but nog least enkele modellen van het Grieks Duitse Edision.
Voor centrale opslag van media gebruik ik een Qnap 219P met tweemaal 2 Tb harddisks + een Synology DS414 met 12 Tb Totale opslag.
-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".
Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.
Re: Openpli 8.2 #59
-
- Senior Member
- 5,517 posts
+115
Excellent
Posted 26 May 2022 - 08:33
VU+ is on the brink of being extinct… Nothing appeared in almost 2 years. Apart from a driver update in februari 2021….
Met één been in het graf..... Helaas
Re: Openpli 8.2 #60
-
- Senior Member
- 162 posts
+1
Neutral
Posted 26 May 2022 - 09:32
Great work on this release!I have one strange problem.When I setup all stuff I have no problems but when I turn on stb next day I have a message Tune failed.
Then i restart the box and everything working again.my box is osmio4k.
Edited by Rudi1, 26 May 2022 - 09:33.
VU+Zero
Osmio4K
14 user(s) are reading this topic
0 members, 14 guests, 0 anonymous users
