41 replies to this topic

[trifonibo558]

I can't tune the receiver after factory reset, it says 'tuner status IDLE' . Any help please!


Sent from my Redmi Note 8 Pro using Tapatalk

[scriptmelvin †]

Factory reset wipes your settings, including tuner settings. You need to reconfigure your tuners.

[trifonibo558]

Thanks for your comment! I can't configure the tuner because there is no satellite in vuplus solo se! Everything is deleted!

Sent from my Redmi Note 8 Pro using Tapatalk

[trifonibo558]

I can't even flash a new image with a USB, I'm really confused.

Sent from my Redmi Note 8 Pro using Tapatalk

[scriptmelvin †]

I guess the easiest thing to do would be to reflash from the menu (Setup -> Flash image). Your box needs internet for that. Then have the setup wizard do automatic tuner configuration.

[trifonibo558]

The receiver is connected to the internet. I have installed openPLi 4,but there is no option "Flash image"

Sent from my Redmi Note 8 Pro using Tapatalk

[scriptmelvin †]

Ow, OpenPLi 4, that's really old... Download a recent OpenPLi and install from USB per these instructions: https://wiki.openpli...h_Vu.2B_Solo_SE

 

If it doesn't work, try different USB sticks. In general, older and smaller USB sticks are more likely to work. Make sure it's formatted as FAT32.

[trifonibo558]

This is how tuner configuration looks like!

Sent from my Redmi Note 8 Pro using Tapatalk

[trifonibo558]

I did insert a usb formatted fat 32 with new image openPLi 7.3 doing the right steps but still nothing!

Sent from my Redmi Note 8 Pro using Tapatalk

[scriptmelvin †]

Do you have other USB sticks? Try them. Preferably max 16GB. And put it in the back of your box.

[piplan1966]

Hi
You should format your USB at least three times to FAT 32,
Your problem will be solved

[trifonibo558]

Hi, I did format fat 32 the usb three times but still nothing!

Sent from my Redmi Note 8 Pro using Tapatalk

[piplan1966]

hi
Download openpli 8.2 on your PC and copy and paste it in your new USB.
Turn off your receiver and plug the USB into the back of the receiver.
Now turn on the receiver, the LED of the receiver will flash three times after which it will start flashing.
After about seven minutes your image will be installed,
Then turn off the receiver and remove the USB,
Turn on the receiver again your image is ok

[trifonibo558]

Thank you very much for your explanation but I have done exactly like that and nothing changed.

Sent from my Redmi Note 8 Pro using Tapatalk

[mimisiku]

There is the slight possibility that you own a clone of the SoloSe (CloudBox 3). This one will only allow VTi 6 or OpenPli 4. If you are sure it actually IS a genuine box you may have a problem with the +5v USB support. You can easily check by putting a USB stick in the box and use the Media Player build in to see if it ‘sees’ the files. If not, your box is faulty. When yes, retry the files..

Use ZIP on a PC, the MAC variant poses problems..

[piplan1966]

hi
Even once everything was deleted from my receiver,
Then I installed the fresh image,
I have a Samsung USB 3.1 Flash Drive 8GB,

[trifonibo558]

I tried Media Player and it works fine with the usb, I don't t think the box is a cloned one. Before I have flashed different images with no problem but now that I did factory reset I stucked in openPLi 4

Sent from my Redmi Note 8 Pro using Tapatalk

[Pr2]

So format the USB key into FAT32 format.

 

Download the image.

Unzip it.

Copy the vuplus folder from your unzip on the root of the USB flash.

 

Remove any other connected USB devices.

Power off the box.

Plug the USB stick that has /vuplus/ in the root.

Turn on the box.

Check the blue led once it is flashing quickly the process is terminated.

 

Here is a full description of the process:

 

https://www.openvix....Vu Solo SE.pdf

[piplan1966]

Hi
Yes, please disconnect all USB cables and HDMI cables before plugging them into the USB receiver.

[mimisiku]

Please post the files you find in the vuplus directory after unpacking.