Posted 12 October 2023 - 08:56
salve a tutti ,è da un po che sto testando le ultime openpli su questo decoder ,ma purtroppo rimane solo il fermo immagine della skin iniziale e basta non và più avanti,posso fare da betatester se volete ,grazie
Hi everyone, I've been testing the latest OpenPLI on this decoder for a while, but unfortunately only the still image of the initial skin remains and that's it, it doesn't go any further, I can act as a beta tester if you want, thanks
Posted 12 October 2023 - 10:08
I can only guess that you have properly configured the tunersettings related to the setup of the dish you use.
Try some FTA channels whether they work.
Some additional information would be nice.
Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.
Dreamboxen heb ik niet meer echt actief. Verder heb ik ook nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET7x00. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. 
Los van de eerder genoemde modellen heb ik nog wel een rits aan testsamples als Mut@nt 2400HD, HD60, GB UE4K, GB Trio4K, Maxitec Multibox combo en Twin, Octagon sf8008, sf8008 mini en last but nog least enkele modellen van het Grieks Duitse Edision.
Voor centrale opslag van media gebruik ik een Qnap 219P met tweemaal 2 Tb harddisks + een Synology DS414 met 12 Tb Totale opslag.
-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".
Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.
Posted 12 October 2023 - 10:58
at the first reboot image stuck at the beginning and that's it, it does not make you configure anything unfortunately
Posted 12 October 2023 - 13:35
Please explain in detail what you have done. Which image exactly? How did you flash it? What happened after the flash was finished? USB disk connected to the box?
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 12 October 2023 - 13:46
I tried them all , openpli-8.3-release-lunix- openpli-7.3-release-lunix openpli-9.0-rc-lunix- openpli-develop-lunix- ,only the openpli-7.1-release-lunix works,All new images remain still at boot
Edited by Lonoe, 12 October 2023 - 13:48.
Posted 12 October 2023 - 13:55
Image loaded with USB stick when I turn on I press the power button, I hope you increase the posts to write, otherwise I can answer tomorrow
Posted 12 October 2023 - 14:19
It flashed correctly? And then, what happened after the reboot?
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 12 October 2023 - 14:30
It flashed correctly And then, all stopped after the reboot, you see only the initial skin and that's it, the other images work without problems, I assume it's just problem openpli 7.3 ,8.3 ,I repeat the 7.1 works fine, and also openatv 7.3 works
Posted 12 October 2023 - 14:32
With "initual skin" you mean the Qviart boot logo, or do you mean the OpenPLi startup screen?
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 12 October 2023 - 14:39
the OpenPLi startup screen,,to be honest my model is the lunix co ,but I noticed that just rename the second folder from Lunix to Lunixco and also works on my model ,the chip is the same ,I hope this is not the problem
Posted 12 October 2023 - 17:28
No idea what a linux co is. But that does explain it, we don't make an image for it.
We'll have to check with Qviart what box is it, and if the images are even compatible (the fact that it flashes doesn't mean it will boot).
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 12 October 2023 - 19:07
uguale a lunix ha solo slot cam Same as Lunix has only cam slots 
Edited by Lonoe, 12 October 2023 - 19:10.
Posted 12 October 2023 - 21:01
Well, apparently not, as it doesn't boot. The fact that the outside looks similar doesn't say anything.
I did a driver check, support for the lunixco was added by the manufacturer on 15/10/2019, but the BSP layer we were given has an older version without that support. We were also not asked to make an image for this box by the manufacturer, so this was never a problem.
So, in short, it is not going to work as long as the manufacturer doesn't provide the support.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 24 October 2023 - 19:28
Edited by EnoSat, 24 October 2023 - 19:29.
Posted 25 October 2023 - 18:19
Fortunately the decoder starts again by putting another image, it's a shame that it doesn't have support though
Posted 11 November 2023 - 13:22
I tried it on a Qviart Lunix this time and I have to say that even if I load the image well there are problems even on it, in practice the gigantic characters come out, I see if I put photos
Posted 11 November 2023 - 14:32
Fortunately the decoder starts again by putting another image, it's a shame that it doesn't have support though
If we don't get support from the manufacturer in the form of a working BSP, we can't build an image for it. It is as simple as that. Don't complain here, complain to the manufacturer.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 11 November 2023 - 16:44
Now I'm talking about the Lunix that I have at hand and I say that there are problems for this too with Openpli , made OpenaTV backup of the Lunico went perfectly in the Lunix , just renamed folder from Lunixco to Lunix, maybe it can be useful ,thanks
Posted 11 November 2023 - 17:17
It is difficult to communicate if you don't read.
We've already told you that we are fully aware that ATV works, and that it works because they have drivers that support the Lunix CO, and we don't. We never got them from Qviart, nor did we ever get the request to provide an image for this box.
So, there will be no OpenPLi for the Lunixco, until Qviart acts, provides us with a working BSP including the correct drivers. For which yoiu need to contact Qviart.
Now I'm talking about the Lunix that I have at hand and I say that there are problems for this too with Openpli
Nothing much will happen unless you elaborate on these "problems"...
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 11 November 2023 - 17:33
se riesco a caricare https://i.postimg.cc...NpF/openpli.jpg questo su lunix This happens on the LUNIX decoder
Edited by Lonoe, 11 November 2023 - 17:36.
0 members, 12 guests, 0 anonymous users
