592 replies to this topic

[hypnos]

Do you wait long enough for the box to boot?  The very first boot after a flash can be slow, the Vu+ Duo has a very small RAM available and its quite slow.

But why are you flashing with Backup plugin, why don't you flash it with the standard USB method?

 

Because if I download img from this site pack had only 2 files and missing root_cfe_auto.jffs2 and this is why cant load firmware from USB method.

 

I have third Vu+Duo and I download VTI which has this three files and had no problem with uprage via USB method.

 

Can you explain me please?

 

Probably damage two receivers Openpli images....................

 

[hypnos]

If I try update third Vu+Duo via USB but VTI img, shows on display Reading USB...

boot_cfe_auto.jffs2

kernel_cfe_auto.bin

root_cfe_auto.jffs2

 

 

 

But I put on USB Openli (had only 2 files) and nothing shows only vu+ and starting old firmware. Not reading from USB

kernel_cfe_auto.bin

root_cfe_auto.jffs2

 

 

Can you explain me?

[WanWizard]

I can see our OpenPLi 4 image has that file, but later versions don't.

 

I did a check, it was removed from the BSP by VU+ in 2017 (https://github.com/O...e7ffd4e5cbe9269), so it isn't the cause of your problem.

 

You are using the exact same USB stick? Formatted with an MBR (GPT is not supported) and a FAT filesystem? And without a "dirty" mark (can be removed by a check of the disk)?

[hypnos]

yes its same USB stick. I dont understand why...

[WanWizard]

Me neither, and I can't check, I've sold my Duo in 2015 or so...

[mudder]

I updated my VU+ Solo 2 without any problem today.

I didn't use an USB stick, I fashed it through the menu. 

[littlesat]

It has a harddisk so it used the harddisk for the download and backup. Then indeed an usb stick is not needed

[engin67]

After updating versions 9.0 and 8.3, there is a constantly rotating screen. please you will need to fix this and I will have to reinstall software with a new usb.

 

[engin67]

engin67, 09 Ocak 2024 - 12:53'te şunları söyledi:

9.0 ve 8.3 versiyonları güncellendikten sonra sürekli dönen bir ekran görünümü ortaya çıkıyor. lütfen bunu düzeltmeniz gerekecek ve yazılımı yeni bir USB kartını yeniden yüklemeniz gerekecek.

08.01.2024 updates, it's been half an hour now, the screen is still spinning

Attached Files

•  2024-01-09 at 12.43.21.jpeg   29.69KB   4 downloads

Edited by engin67, 9 January 2024 - 11:03.

[Frenske]

@Engin67

 

I have no clue what you did but I flashed my sf8008 recently and it works as expected. I also installed the Denys image online and again no issues.

Today or after the new 8.3 and / or 9.0 build the new drivers will be loaded. In the NB they are already loaded.

[engin67]

@Engin67

 

I have no clue what you did but I flashed my sf8008 recently and it works as expected. I also installed the Denys image online and again no issues.

Today or after the new 8.3 and / or 9.0 build the new drivers will be loaded. In the NB they are already loaded.

First of all, thank you very much for your answer. I updated the 9.0 update dated 08.01.2024 from the software update section of my sf8008 device, which is what I always do. This is the first time I encountered something like this. I wanted to update the version dated 08.01.2024 by opening the 8.3 version again, unfortunately I encountered the same constantly rotating screens. Even though the channel order is visible on the device panel, the device remains the same for hours... Thank you very much for the software. I have been using your software on different devices for years.

Now I will have to install it via written USB to get rid of this error, I wish you luck.

[Frenske]

I will test it ASAP and see whether I experience the same issue.

[Frenske]

I just upgraded my OpenPLi 9.0 from an earlier version which I installed just now, and via the menu updated my image which worked perfect. So I did an update from the image of 24 December to the one from Januari 9th and as you can see this worked ok. It also contained the latest Octagon drivers. As far as I'm concerned case closed. Maybe some fuzzy plugin causes this issue.

 

 sf8008-1.PNG   508.19KB   8 downloads   sf8008-2.PNG   560.87KB   8 downloads

[engin67]

OpenPLi 9.0'ımı az önce kurulan önceki bir sürümden yükselttim ve menü aracılığıyla mükemmel çalışan imajımı güncelledim. Böylece 24 Aralık'taki görüntüden 9 Ocak'taki görüntüye bir güncelleme yaptım ve gördüğünüz gibi bu işe yaradı. Ayrıca en son Octagon sürücülerini de etkileyebilir. Bana ait dava kapandı. Belki bazı eklentiler bu soruna neden oluyordur.

 

sf8008-1.PNG   sf8008-2.PNG

Dün akşam yapılan 2. güncellemeden sonra cihaz açılmıyor.

 

Cihazdaki kanal listesi düzenleme programıyla bilgisayarıma indirdim. Flash xp programı ile sf8008 cihazına wifi üzerinden bağlanıyorum. Buradan yapabileceğim bir şey var mı? Son güncellemeyi iptal edebilir miyim veya olabilir miyim? Saygılarımızla.

 

(-- Google translate)

After the second update last night, the device does not turn on.

I downloaded it to my computer with the channel list editing program on the device. I connect to the SF8008 device via wifi with the Flash XP program. Is there anything I can do from here? Can I cancel or be the last update? Regards.

Attached Files

•  2024-01-09 at 18.45.56.jpeg   112.49KB   6 downloads
•  2024-01-09 at 18.45.58.jpeg   23.54KB   6 downloads
•  2024-01-09 at 18.46.00.jpeg   162.21KB   6 downloads
•  2024-01-09 at 18.55.42.jpeg   208.62KB   6 downloads

Edited by Tech, 9 January 2024 - 19:06.
Added English translation

[Frenske]

Start all over again and boot the 8008 and push and hold the power button of the box. Update appears. Then install from internet the Openpli image. I really have no clue what you mean with the lines you wrote. BTW, I absolutely don’t prefer connecting via WiFi so try to do this via a wired connection. 
You can also unpack an Openpli USB image on your USB stick and install a restore image and the Openpli image will be installed too. When you have a proper backup on your stick this will be restored too.

[engin67]

Her şeyi yeniden başlatın ve 8008'i önyükleyin ve kutunun güç düğmesini basılı tutun. Güncelleme görünüyor. Daha sonra internetten Openpli imajını yükleyin. Yazdığın satırlarla ne demek istediğime dair gerçekten hiçbir fikrim yok. BTW, kesinlikle WiFi üzerinden bağlanmayı tercih etmiyor, bu nedenle bu düğmelerin bağlantı yoluyla çalıştırılması hatası veriyor. 
Ayrıca USB disklerindeki bir Openpli USB değiştirme paketinden ve bir geri yükleme görüntüsünü yükleyebilirsiniz; Openpli görüntüsü yüklenecektir. Çubuğunuzda uygun bir yedekleme olduğunda bu da geri yüklenecektir.

Yeni 9.0 imajını ve 08.01.2024 tarihli yazılımı yeniden yükledim. Bunu farkettim, sanırım güncelleme boot logosu hatası veriyor. Yeni versiyonda boot logosu 2023 logosu ile aynı, güncellemede ise boot logosu unutuluyor ve cihaz bunu algılamadığında hep aynı ekranda kalıyor. 8.3 sürümünde de aynı hata oluştu, açılmadı, maalesef güncelleme paketiniz hatalıydı. Şimdi ayarları, eklentileri ve piconları yeniden yükledim. İyi akşamlar.

Attached Files

•  2024-01-09 at 23.03.04.jpeg   98.2KB   3 downloads
•  2024-01-09 at 22.57.51.jpeg   113.19KB   3 downloads

[Frenske]

Only English in this section. I won’t translate it myself.

[Tech]

There is nothing wrong with the bootlogo, it was simply reset to the standard bootlogo after the Christmas and New Year logo,

given the fact that you see the old logo again, indicates you are provided with the latest updates

 

Next time there will be no response if something is posted in the Turkish language again, apparently you can find the translation given Frenske's response translated from English to Turkish, then it is a small effort to also convert your text into English to have it translated.

[engin67]

There is nothing wrong with the bootlogo, it was simply reset to the standard bootlogo after the Christmas and New Year logo,

given the fact that you see the old logo again, indicates you are provided with the latest updates

 

Next time there will be no response if something is posted in the Turkish language again, apparently you can find the translation given Frenske's response translated from English to Turkish, then it is a small effort to also convert your text into English to have it translated.

I was using versions 9.0 and 8.3 and had made the latest updates for both versions. I saw that there was a second update for 9.0 on the night of 08.01.2024 and wanted to update it as usual. But the device did not turn on and remained in a constant state of waiting on the channel. I also saw the update dated 08.01.2024 for 8.3. Likewise, it did not open after the update. Good luck, I reinstalled it. I translate it into English from Google and send it that way. But since your site automatically translates it into Turkish, it appeared on the page that way. If you hadn't written it, I wouldn't have had the information. I am sending it in English now, I hope there will be no problem. Kind regards.

[40H3X]

Thanks for reporting back and good that a reinstall has resolved the error.