Jump to content


Photo

Box won't boot.


  • Please log in to reply
11 replies to this topic

#1 foxbob

  • Senior Member
  • 624 posts

+18
Neutral

Posted 6 February 2024 - 11:40

Also,after the reboot the box stopped loading.Not a single firmware is loaded.If the flash drive has firmware it offers to flash the receiver.For a very long time there is an inscription on the screen Updating rootfs and the inscription can be visible for about 1 hour.But the receiver still does not start.I made a start log via putty, but I can’t force start the firmware when I click on CTRL-C the log doesn't stop.

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2024.02.01 19:24:03 =~=~=~=~=~=~=~=~=~=~=~=
 ю CPU 0123
BCM74450040
PRID74440040
v1.21
RR:00000003
BFW
seclib-1.9
BBL v1.0.1
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON

single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MEMSYS-ALT
SHMOO 02010100 BLD:exported HW:hpf0_b1p3 V:2.1.1.0
MCB: FLEX
AVS start:status=000000ff
STB: Current voltage=00000396(918)
 temperature=00009bf0(39920)
 PV=00000354(852)
 MV=00000397(919)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: !@ ffe0e780 <= ffe0d9f4 MEMSYS-0 @ f1100000 OK
DDR1: =@ ffe0e780 <= ffe0d9f4 MEMSYS-1 @ f1180000 OK
DDR2: =@ ffe0e780 <= ffe0d9f4 MEMSYS-2 @ f1200000 OK
Sdram Scramble OTP = 0x00000001 
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f 
bfw_hash_locked = 0x00000000 
BFW key3 OK, BFW load OK
BFW v4.1.5
COPY CODE... DONE
MICH: disable success
SSBL
SEC: jtag debug status: 000000af
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss  07089dd8
_ebss  070c9538
_end   070c9558
HEAP @ 07100000
STACK @ 09200000
ARCH: CONFIG OK
CLR BSS 07089dd8 to 070c9538 OK
CLR SRAM  OK
CACHE FLUSH OK
CPU CLKSET OK
GO!

[33;1m    ,/   [0m 
[33;1m  ,'/___,[0m BOLT v1.21 v1.21 LOCAL BUILD
[33;1m.'__  ,' [0m (2016-10-17 16:21:51 Vuplus team)
[33;1m   /,'   [0m Copyright (C) 2016 Broadcom
[33;1m  /'     [0m 
[0m
Board: ULTIMO4K
SYS_CTRL: product=7444, family=7445e0, strap=000005b6, 
otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000) 
otp @ 0xf0404034 = 0x00000001: moca2_disable(0x00000001) 
CPU: 4x B15 [420f00f3] 1503 MHz
SCB: 432 MHz
DDR0 @ 1200MHz, DDR1 @ 1200MHz, DDR2 @ 1200MHz
RESET CAUSE: 0x000003 main_chip_input power_on (2 of 21 possible causes)
CS0: SFDP SPI, 4MB, 64kB blocks, 64kB erase block, 256B pages
[31;1mCS1: NAND: unrecognized ID: 0xffffff 0xffffffff[0m
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
RTS2: 0x1201004, 256 clients, ok
BOX MODE: 1
SPLASH: starting
SPLASH BMEM init @ 40000000
SPLASH BMEM init @ 80000000
SPLASH BMEM init @ c0000000
SPLASH: Old format file in flash. Use splash_create_flash_file to create newer format.
Loaded BMP: W=720 H=480
SPLASH: audio not present
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.918V, T=+41.381C, PV=0.852V, MV=0.919V, FW=30333278 [0.3.2.x]
check_tuner_version
i2c_readsw
Tuner Version [0x2]
LCD_Init Complete
boot device name [flash0.bolt]
waiting for usb...
usb: resetting device on bus 4 hub 1 port 1[J


USB: New high speed device connected to bus 4 hub 1 port 1[J


usb: resetting device on bus 4 hub 2 port 1[J


USB: New high speed device connected to bus 4 hub 2 port 1[J

usb: no driver found for 0a5c:bd27

usb: resetting device on bus 4 hub 2 port 2[J


USB: New full speed device connected to bus 4 hub 2 port 2[J


USB: Lower speed devices not supported under high speed hub[J


usb: resetting device on bus 5 hub 1 port 1[J


USB: New high speed device connected to bus 5 hub 1 port 1[J

usb: found Mass-Storage Device 8564:1000

USBMASS: Unit 0 connected[J

done
checking usb
No Priority Usb
checking front key
readFrontKey 0 0
Check ignore.update file
Checking usbdisk0:/vuplus/ultimo4k/ignore.update......NO
Check force.update file
Checking usbdisk0:/vuplus/ultimo4k/force.update......NO
bolt update ...Checking usbdisk0:/vuplus/ultimo4k/bolt_auto.bin......NO
Checking usbdisk0:/vuplus/ultimo4k/rootfs.tar.bz2......YES
Checking usbdisk0:/vuplus/ultimo4k/splash_auto.bin......NO
Checking usbdisk0:/vuplus/ultimo4k/kernel_auto.bin......YES
Checking usbdisk0:/vuplus/ultimo4k/reboot.update......YES
waiting for update key
readFrontKey 0x0
readFrontKey 0x0
readFrontKey 0x0
Skipping USB Update
Loader:zimg Filesys:raw Dev:emmcflash0.kernel File: Options:root=/dev/mmcblk0p4 rootfstype=ext4 rootflags=data=journal rootwait rw coherent_pool=2M vmalloc=600m bmem=608m@416m bmem=416m@1632m bmem=699m@2357m
Reading 4205024 bytes from zImage...........
Starting program at 0x8000 (DTB @ 0x7628000)

32 bit direct boot...
Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.28-1.12 (oe-user@oe-host) (gcc version 13.2.0 (GCC) ) #1 SMP Sun Jan 28 04:02:33 UTC 2024
[    0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c7387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine model: ULTIMO4K
[    0.000000] moving dtb from 0x0000000007628000 to 0x0000000000865248
[    0.000000] bmem: Reserved 630 MiB at 0x0000000018a00000
[    0.000000] bmem: Reserved 383 MiB at 0x0000000068100000
[    0.000000] bmem: Reserved 443 MiB at 0x00000000a4100000
[    0.000000] cma: Reserved 16 MiB at 0x0000000017000000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] MCP: Enabling write pairing
[    0.000000] PERCPU: Embedded 8 pages/cpu @d81b0000 s8768 r8192 d15808 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 785660
[    0.000000] Kernel command line: root=/dev/mmcblk0p4 rootfstype=ext4 rootflags=data=journal rootwait rw coherent_pool=2M vmalloc=622m bmem=630m@394m bmem=383m@1665m bmem=443m@2625m
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 1600376K/3145728K available (5909K kernel code, 334K rwdata, 1872K rodata, 252K init, 189K bss, 1528968K reserved, 16384K cma-reserved, 1255412K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd8800000 - 0xff000000   ( 616 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd8200000   ( 386 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc07a17d0   (7782 kB)
[    0.000000]       .init : 0xc07a2000 - 0xc07e1240   ( 253 kB)
[    0.000000]       .data : 0xc07e2000 - 0xc0835b58   ( 335 kB)
[    0.000000]        .bss : 0xc0835b60 - 0xc0865248   ( 190 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc403000, parent irq: 94)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc3e1000, parent irq: 64)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc410640, parent irq: 96)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc4d1200, parent irq: 48)
[    0.000000] Architected cp15 timer(s) running at 27.00MHz (virt).
[    0.000004] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 2545165795328ns
[    0.000009] Switching to timer-based delay loop
[    0.000275] Console: colour dummy device 80x30
[    0.000295] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
[    0.000303] pid_max: default: 32768 minimum: 301
[    0.000401] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000406] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.005847] CPU: Testing write buffer coherency: ok
[    0.006057] CPU0: update cpu_power 1024
[    0.006063] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.006186] Setting up static identity map for 0x5a5480 - 0x5a54d8
[    0.008545] CPU1: Booted secondary processor
[    0.008561] CPU1: update cpu_power 1024
[    0.008564] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.009177] CPU2: Booted secondary processor
[    0.009188] CPU2: update cpu_power 1024
[    0.009191] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.009776] CPU3: Booted secondary processor
[    0.009787] CPU3: update cpu_power 1024
[    0.009790] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.009840] Brought up 4 CPUs
[    0.009857] SMP: Total of 4 processors activated.
[    0.009861] CPU: All CPU(s) started in SVC mode.
[    0.010214] devtmpfs: initialized
[    0.013829] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
[    0.014819] regulator-dummy: no parameters
[    0.015004] NET: Registered protocol family 16
[    0.017105] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.017892] cpuidle: using governor ladder
[    0.017898] cpuidle: using governor menu
[    0.020969] irq: no irq domain found for /rdb/interrupt-controller@f040a780 !
[    0.021123] irq: no irq domain found for /rdb/interrupt-controller@f0417280 !
[    0.025025] irq: no irq domain found for /rdb/interrupt-controller@f03e1a00 !
[    0.025297] syscon f0404000.syscon: regmap [mem 0xf0404000-0xf040451b] registered
[    0.026057] syscon f0404100.syscon: regmap [mem 0xf0404100-0xf040415b] registered
[    0.026212] syscon f040415c.syscon: regmap [mem 0xf040415c-0xf040419b] registered
[    0.026356] syscon f0410700.syscon: regmap [mem 0xf0410700-0xf041070b] registered
[    0.026492] syscon f041070c.syscon: regmap [mem 0xf041070c-0xf0410713] registered
[    0.026643] syscon f1101004.syscon: regmap [mem 0xf1101004-0xf1101403] registered
[    0.026782] syscon f1181004.syscon: regmap [mem 0xf1181004-0xf1181403] registered
[    0.026932] syscon f1201004.syscon: regmap [mem 0xf1201004-0xf1201403] registered
[    0.027062] syscon f0404080.syscon: regmap [mem 0xf0404080-0xf0404083] registered
[    0.027205] syscon f04040a4.syscon: regmap [mem 0xf04040a4-0xf04040a7] registered
[    0.027339] syscon f03e0154.syscon: regmap [mem 0xf03e0154-0xf03e0157] registered
[    0.027481] syscon f03e0354.syscon: regmap [mem 0xf03e0354-0xf03e0357] registered
[    0.027617] syscon f03e0400.syscon: regmap [mem 0xf03e0400-0xf03e0403] registered
[    0.028245] irq: no irq domain found for /rdb/interrupt-controller@f0417280 !
[    0.028785] syscon f03e2400.syscon: regmap [mem 0xf03e2400-0xf03e27ff] registered
[    0.028934] syscon f0452000.syscon: regmap [mem 0xf0452000-0xf04520ff] registered
[    0.029236] No ATAGs?
[    0.029254] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.029260] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.029380] Broadcom Brahma-B15 readahead cache at: 0xfc3e2478
[    0.044479] bio: create slab <bio-0> at 0
[    0.045168] SCSI subsystem initialized
[    0.045852] usbcore: registered new interface driver usbfs
[    0.045936] usbcore: registered new interface driver hub
[    0.046033] usbcore: registered new device driver usb
[    0.046157] Linux video capture interface: v2.00
[    0.046362] pps_core: LinuxPPS API ver. 1 registered
[    0.046366] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.046421] PTP clock support registered
[    0.046965] Advanced Linux Sound Architecture Driver Initialized.
[    0.047684] cfg80211: Calling CRDA to update world regulatory domain
[    0.048097] brcm-pci f0460000.pcie: adjusting to legacy (broken) pcie DT
[    0.048285] brcm-pci f0490000.pcie: adjusting to legacy (broken) pcie DT
[    0.148584] brcm-pci f0460000.pcie: link down
[    0.248885] brcm-pci f0490000.pcie: link down
[    0.248934] Switched to clocksource arch_sys_counter
[    0.249110] FS-Cache: Loaded
[    0.257862] thermal thermal_zone0: failed to read out thermal zone 0
[    0.257974] NET: Registered protocol family 2
[    0.258347] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.258374] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.258418] TCP: Hash tables configured (established 4096 bind 4096)
[    0.258483] TCP: reno registered
[    0.258490] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.258503] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.258622] NET: Registered protocol family 1
[    0.258804] RPC: Registered named UNIX socket transport module.
[    0.258808] RPC: Registered udp transport module.
[    0.258811] RPC: Registered tcp transport module.
[    0.258815] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.259038] hw perfevents: enabled with ARMv7 Cortex-A15 PMU driver, 7 counters available
[    0.260291] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.261007] bounce pool size: 64 pages
[    0.261653] NFS: Registering the id_resolver key type
[    0.261679] Key type id_resolver registered
[    0.261683] Key type id_legacy registered
[    0.261694] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.261698] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.261846] FS-Cache: Netfs 'cifs' registered for caching
[    0.261904] Key type cifs.spnego registered
[    0.262062] fuse init (API version 7.22)
[    0.262203] msgmni has been set to 705
[    0.262870] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.262876] io scheduler noop registered
[    0.262880] io scheduler deadline registered
[    0.262905] io scheduler cfq registered (default)
[    0.263130] brcm-gisb-arb f0400000.gisb-arb: registered mem: fc400000, irqs: 258, 259
[    0.293351] brcm-waketimer f0417580.waketimer: registered, with irq 260
[    0.293615] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.294978] f040ab00.serial: ttyS0 at MMIO 0xf040ab00 (irq = 107, base_baud = 5062500) is a 16550A
[    1.125022] console [ttyS0] enabled
[    1.128901] f040ab40.serial: ttyS1 at MMIO 0xf040ab40 (irq = 108, base_baud = 5062500) is a 16550A
[    1.138250] f040ab80.serial: ttyS2 at MMIO 0xf040ab80 (irq = 109, base_baud = 5062500) is a 16550A
[    1.150670] loop: module loaded
[    1.154419] ahci brcmstb-ahci.0: can't get clock
[    1.159132] ahci brcmstb-ahci.0: SSS flag set, parallel bus scan disabled
[    1.176949] ahci brcmstb-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[    1.185580] ahci brcmstb-ahci.0: flags: 64bit ncq sntf stag pm clo pmp slum part 
[    1.195201] scsi0 : ahci_platform
[    1.198845] scsi1 : ahci_platform
[    1.202397] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 62
[    1.210331] ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x180 irq 62
[    1.219482] spi_brcmstb f03e3400.spi: 1-lane output, 3-byte address
[    1.225862] spi_brcmstb f03e3400.spi: master is unqueued, this is deprecated
[    1.233184] m25p80 spi32766.0: found mx25l3255e, expected m25p80
[    1.239209] m25p80 spi32766.0: mx25l3255e (4096 Kbytes)
[    1.244469] 5 ofpart partitions found on MTD device spi32766.0
[    1.250314] Creating 5 MTD partitions on "spi32766.0":
[    1.255467] 0x000000000000-0x000000200000 : "flash0.bolt"
[    1.261552] 0x000000200000-0x000000210000 : "flash0.macadr"
[    1.267759] 0x000000210000-0x000000220000 : "flash0.nvram"
[    1.273882] 0x000000220000-0x000000230000 : "flash0.devtree"
[    1.280188] 0x000000000000-0x000000400000 : "flash0"
[    1.286847] libphy: Fixed MDIO Bus: probed
[    1.293303] libphy: unimac MII bus: probed
[    1.301652] unimac-mdio f0b403c0.mdio: Broadcom UniMAC MDIO bus at 0xfcb403c0
[    1.309589] brcm-systemport f04a0000.ethernet: Broadcom SYSTEMPORTv 1.00 at 0xfc4a0000 (irqs: 54, 55, TXQs: 32, RXQs: 1)
[    1.323164] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.329015] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.335454] xhci-brcm: xHCI BRCM driver
[    1.339377] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[    1.345194] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1
[    1.353309] xhci-brcm f0471000.xhci_v2: irq 115, io mem 0xf0471000
[    1.360019] hub 1-0:1.0: USB hub found
[    1.363803] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    1.371067] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[    1.376871] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2
[    1.385200] hub 2-0:1.0: USB hub found
[    1.388978] hub 2-0:1.0: 2 ports detected
[    1.393386] ehci-brcm: EHCI BRCM driver
[    1.397300] ehci-brcm f0470300.ehci_v2: EHCI Host Controller
[    1.403119] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3
[    1.421075] ehci-brcm f0470300.ehci_v2: irq 111, io mem 0xf0470300
[    1.432941] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.439601] hub 3-0:1.0: USB hub found
[    1.443379] hub 3-0:1.0: 1 port detected
[    1.447518] ehci-brcm f0470500.ehci_v2: EHCI Host Controller
[    1.453326] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4
[    1.471273] ehci-brcm f0470500.ehci_v2: irq 112, io mem 0xf0470500
[    1.482940] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.486952] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.487194] ata1.00: ATA-11: KINGSTON SUV400S37120G, 0C3J96R9, max UDMA/133
[    1.487198] ata1.00: 234441648 sectors, multi 1: LBA48 NCQ (depth 31/32)
[    1.487508] ata1.00: configured for UDMA/133
[    1.487718] scsi 0:0:0:0: Direct-Access     ATA      KINGSTON SUV400S 0C3J PQ: 0 ANSI: 5
[    1.488310] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[    1.488314] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    1.488489] sd 0:0:0:0: [sda] Write Protect is off
[    1.488548] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.548574] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.554017] hub 4-0:1.0: USB hub found
[    1.554359]  sda: sda1
[    1.555117] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.564787] hub 4-0:1.0: 1 port detected
[    1.568991] ehci-brcm f0480300.ehci_v2: EHCI Host Controller
[    1.574833] ehci-brcm f0480300.ehci_v2: new USB bus registered, assigned bus number 5
[    1.592817] ehci-brcm f0480300.ehci_v2: irq 117, io mem 0xf0480300
[    1.604940] ehci-brcm f0480300.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.611617] hub 5-0:1.0: USB hub found
[    1.615393] hub 5-0:1.0: 1 port detected
[    1.619527] ehci-brcm f0480500.ehci_v2: EHCI Host Controller
[    1.625347] ehci-brcm f0480500.ehci_v2: new USB bus registered, assigned bus number 6
[    1.643296] ehci-brcm f0480500.ehci_v2: irq 118, io mem 0xf0480500
[    1.654939] ehci-brcm f0480500.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.661617] hub 6-0:1.0: USB hub found
[    1.665396] hub 6-0:1.0: 1 port detected
[    1.669671] ohci-brcm: OHCI BRCM driver
[    1.673589] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller
[    1.677944] ata2: SATA link down (SStatus 0 SControl 300)
[    1.684825] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 7
[    1.692714] ohci-brcm f0470400.ohci_v2: irq 113, io mem 0xf0470400
[    1.753423] hub 7-0:1.0: USB hub found
[    1.757202] hub 7-0:1.0: 1 port detected
[    1.761342] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller
[    1.767163] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 8
[    1.775049] ohci-brcm f0470600.ohci_v2: irq 114, io mem 0xf0470600
[    1.836407] hub 8-0:1.0: USB hub found
[    1.840185] hub 8-0:1.0: 1 port detected
[    1.844322] ohci-brcm f0480400.ohci_v2: BRCM OHCI controller
[    1.850142] ohci-brcm f0480400.ohci_v2: new USB bus registered, assigned bus number 9
[    1.858022] ohci-brcm f0480400.ohci_v2: irq 119, io mem 0xf0480400
[    1.919402] hub 9-0:1.0: USB hub found
[    1.922957] usb 5-1: new high-speed USB device number 2 using ehci-brcm
[    1.929797] hub 9-0:1.0: 1 port detected
[    1.933945] ohci-brcm f0480600.ohci_v2: BRCM OHCI controller
[    1.939781] ohci-brcm f0480600.ohci_v2: new USB bus registered, assigned bus number 10
[    1.947750] ohci-brcm f0480600.ohci_v2: irq 120, io mem 0xf0480600
[    2.009418] hub 10-0:1.0: USB hub found
[    2.013285] hub 10-0:1.0: 1 port detected
[    2.017625] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.024174] ehci-pci: EHCI PCI platform driver
[    2.028712] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.034917] ohci-pci: OHCI PCI platform driver
[    2.039733] hub 5-1:1.0: USB hub found
[    2.043520] usbcore: registered new interface driver usb-storage
[    2.049571] hub 5-1:1.0: 4 ports detected
[    2.049717] mousedev: PS/2 mouse device common for all mice
[    2.050153] i2c /dev entries driver
[    2.050541] IR NEC protocol handler initialized
[    2.050544] IR RC5(x) protocol handler initialized
[    2.050545] IR RC6 protocol handler initialized
[    2.050547] IR JVC protocol handler initialized
[    2.050548] IR Sony protocol handler initialized
[    2.050551] IR RC5 (streamzap) protocol handler initialized
[    2.050552] IR SANYO protocol handler initialized
[    2.050554] IR MCE Keyboard/mouse protocol handler initialized
[    2.050907] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor driver
[    2.051133] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    2.051397] sdhci: Secure Digital Host Controller Interface driver
[    2.051398] sdhci: Copyright(c) Pierre Ossman
[    2.051400] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.052521] mmc0: no vqmmc regulator found
[    2.052525] mmc0: no vmmc regulator found
[    2.082938] mmc0: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA
[    2.083231] hidraw: raw HID events driver (C) Jiri Kosina
[    2.087686] usbcore: registered new interface driver usbhid
[    2.087687] usbhid: USB HID core driver
[    2.150580] mmc0: BKOPS_EN bit is not set
[    2.156833] mmc0: new high speed MMC card at address 0001
[    2.158111] mmcblk0: mmc0:0001 4FPD3R 3.64 GiB 
[    2.158202] mmcblk0boot0: mmc0:0001 4FPD3R partition 1 4.00 MiB
[    2.158295] mmcblk0boot1: mmc0:0001 4FPD3R partition 2 4.00 MiB
[    2.158376] mmcblk0rpmb: mmc0:0001 4FPD3R partition 3 512 KiB
[    2.161801]  mmcblk0: p1 p2 p3 p4
[    2.164652]  mmcblk0boot1: unknown partition table
[    2.165349]  mmcblk0boot0: unknown partition table
[    2.205977] TCP: cubic registered
[    2.209326] NET: Registered protocol family 17
[    2.213948] Distributed Switch Architecture driver version 0.1
[    2.219855] sys0[0]: detected a Broadcom Starfighter 2 switch
[    2.225857] Starfighter 2 top: 4.00, core: 2.00 base: 0xfcb00000, IRQs: 56, 57
[    2.233250] libphy: dsa slave smi: probed
[    2.293937] f0b403c0.mdio:05: Broadcom BCM7445 PHY revision: 0x10, patch: 3
[    2.508043] usb 5-1.1: new high-speed USB device number 3 using ehci-brcm
[    2.528036] attached PHY at address 5 [Broadcom BCM7445]
[    2.533795] net eth0: PHY already attached
[    2.538086] Key type dns_resolver registered
[    2.542418] Registering SWP/SWPB emulation handler
[    2.547658] regulator-dummy: disabling
[    2.554625] ALSA device list:
[    2.557608]   No soundcards found.
[    2.561808] EXT4-fs: Warning: mounting with data=journal disables delayed allocation and O_DIRECT support!
[    2.675055] usb 5-1.2: new full-speed USB device number 4 using ehci-brcm
[    2.947980] usb 6-1: new high-speed USB device number 2 using ehci-brcm
[    3.069846] usb-storage 6-1:1.0: USB Mass Storage device detected
[    3.076253] scsi2 : usb-storage 6-1:1.0
[    3.151117] random: nonblocking pool is initialized
[    4.082636] scsi 2:0:0:0: Direct-Access     JetFlash Transcend 8GB    1.00 PQ: 0 ANSI: 6
[    4.091804] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    4.092226] sd 2:0:0:0: [sdb] 15433728 512-byte logical blocks: (7.90 GB/7.35 GiB)
[    4.092593] sd 2:0:0:0: [sdb] Write Protect is off
[    4.092971] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
[    4.121991]  sdb: sdb1 sdb2
[    4.126966] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[   13.535942] mmc0: Timeout waiting for hardware interrupt.
[   13.543353] ------------[ cut here ]------------
[   13.547987] WARNING: CPU: 0 PID: 0 at /usr/src/debug/linux-vuplus/3.14.28/drivers/mmc/host/sdhci.c:994 sdhci_send_command+0x798/0xf0c()
[   13.560171] Modules linked in:
[   13.563243] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.28-1.12 #1
[   13.569710] [<c0015f70>] (unwind_backtrace) from [<c0011e1c>] (show_stack+0x10/0x14)
[   13.577469] [<c0011e1c>] (show_stack) from [<c059cc54>] (dump_stack+0x6c/0x7c)
[   13.584705] [<c059cc54>] (dump_stack) from [<c059abc0>] (warn_slowpath_common+0x68/0x84)
[   13.592810] [<c059abc0>] (warn_slowpath_common) from [<c0022a7c>] (warn_slowpath_null+0x1c/0x24)
[   13.601608] [<c0022a7c>] (warn_slowpath_null) from [<c045eeb0>] (sdhci_send_command+0x798/0xf0c)
[   13.610408] [<c045eeb0>] (sdhci_send_command) from [<c0460cbc>] (sdhci_timeout_timer+0x74/0xb8)
[   13.619118] [<c0460cbc>] (sdhci_timeout_timer) from [<c002c9b4>] (call_timer_fn.isra.0+0x20/0x7c)
[   13.628003] [<c002c9b4>] (call_timer_fn.isra.0) from [<c002cb5c>] (run_timer_softirq+0x14c/0x218)
[   13.636885] [<c002cb5c>] (run_timer_softirq) from [<c0026e78>] (__do_softirq+0x10c/0x2a8)
[   13.645072] [<c0026e78>] (__do_softirq) from [<c00272a8>] (irq_exit+0xe0/0x118)
[   13.652390] [<c00272a8>] (irq_exit) from [<c000f7e0>] (handle_IRQ+0x44/0x90)
[   13.659448] [<c000f7e0>] (handle_IRQ) from [<c000858c>] (gic_handle_irq+0x2c/0x5c)
[   13.667029] [<c000858c>] (gic_handle_irq) from [<c0012840>] (__irq_svc+0x40/0x50)
[   13.674518] Exception stack(0xc07e3f58 to 0xc07e3fa0)
[   13.679575] 3f40:                                                       ffffffed 179d1000
[   13.687761] 3f60: c07eb3ec 00000000 c07e2000 c05a808c c0829de4 c07ea444 c06bc044 00000001
[   13.695947] 3f80: c07d5628 00000000 d81b0fe0 c07e3fa0 c000fb04 c000fafc 60000113 ffffffff
[   13.704135] [<c0012840>] (__irq_svc) from [<c000fafc>] (arch_cpu_idle+0x2c/0x38)
[   13.711542] [<c000fafc>] (arch_cpu_idle) from [<c005feac>] (cpu_startup_entry+0x74/0x138)
[   13.719733] [<c005feac>] (cpu_startup_entry) from [<c07a2bb8>] (start_kernel+0x40c/0x418)
[   13.727921] [<c07a2bb8>] (start_kernel) from [<00008084>] (0x8084)
[   13.734108] ---[ end trace 70c38a30b36c9d64 ]---
[   13.740836] mmcblk0: error -110 transferring data, sector 73536, nr 16, cmd response 0x0, card status 0x400d00
[   13.750862] end_request: I/O error, dev mmcblk0, sector 73536
[   13.756624] Buffer I/O error on device mmcblk0p4, logical block 232
[   13.762904] lost page write due to I/O error on mmcblk0p4
[   13.768322] end_request: I/O error, dev mmcblk0, sector 73544
[   13.774081] Buffer I/O error on device mmcblk0p4, logical block 233
[   13.780361] lost page write due to I/O error on mmcblk0p4
[   23.807947] mmc0: Timeout waiting for hardware interrupt.
[   23.815355] ------------[ cut here ]------------
[   23.819982] WARNING: CPU: 0 PID: 0 at /usr/src/debug/linux-vuplus/3.14.28/drivers/mmc/host/sdhci.c:994 sdhci_send_command+0x798/0xf0c()
[   23.832164] Modules linked in:
[   23.835235] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W    3.14.28-1.12 #1
[   23.842644] [<c0015f70>] (unwind_backtrace) from [<c0011e1c>] (show_stack+0x10/0x14)
[   23.850401] [<c0011e1c>] (show_stack) from [<c059cc54>] (dump_stack+0x6c/0x7c)
[   23.857634] [<c059cc54>] (dump_stack) from [<c059abc0>] (warn_slowpath_common+0x68/0x84)
[   23.865736] [<c059abc0>] (warn_slowpath_common) from [<c0022a7c>] (warn_slowpath_null+0x1c/0x24)
[   23.874534] [<c0022a7c>] (warn_slowpath_null) from [<c045eeb0>] (sdhci_send_command+0x798/0xf0c)
[   23.883332] [<c045eeb0>] (sdhci_send_command) from [<c0460cbc>] (sdhci_timeout_timer+0x74/0xb8)
[   23.892042] [<c0460cbc>] (sdhci_timeout_timer) from [<c002c9b4>] (call_timer_fn.isra.0+0x20/0x7c)
[   23.900925] [<c002c9b4>] (call_timer_fn.isra.0) from [<c002cb5c>] (run_timer_softirq+0x14c/0x218)
[   23.909807] [<c002cb5c>] (run_timer_softirq) from [<c0026e78>] (__do_softirq+0x10c/0x2a8)
[   23.917993] [<c0026e78>] (__do_softirq) from [<c00272a8>] (irq_exit+0xe0/0x118)
[   23.925311] [<c00272a8>] (irq_exit) from [<c000f7e0>] (handle_IRQ+0x44/0x90)
[   23.932369] [<c000f7e0>] (handle_IRQ) from [<c000858c>] (gic_handle_irq+0x2c/0x5c)
[   23.939948] [<c000858c>] (gic_handle_irq) from [<c0012840>] (__irq_svc+0x40/0x50)
[   23.947437] Exception stack(0xc07e3f58 to 0xc07e3fa0)
[   23.952493] 3f40:                                                       ffffffed 179d1000
[   23.960678] 3f60: c07eb3ec 00000000 c07e2000 c05a808c c0829de4 c07ea444 c06bc044 00000001
[   23.968864] 3f80: c07d5628 00000000 00000000 c07e3fa0 c000fb04 c000fafc 60000113 ffffffff
[   23.977052] [<c0012840>] (__irq_svc) from [<c000fafc>] (arch_cpu_idle+0x2c/0x38)
[   23.984458] [<c000fafc>] (arch_cpu_idle) from [<c005feac>] (cpu_startup_entry+0x74/0x138)
[   23.992645] [<c005feac>] (cpu_startup_entry) from [<c07a2bb8>] (start_kernel+0x40c/0x418)
[   24.000830] [<c07a2bb8>] (start_kernel) from [<00008084>] (0x8084)
[   24.007015] ---[ end trace 70c38a30b36c9d65 ]---
[   24.013728] mmcblk0: error -110 transferring data, sector 73672, nr 8, cmd response 0x0, card status 0x400d00
[   24.023661] end_request: I/O error, dev mmcblk0, sector 73672
[   24.029420] Buffer I/O error on device mmcblk0p4, logical block 249
[   24.035699] lost page write due to I/O error on mmcblk0p4
[   34.079953] mmc0: Timeout waiting for hardware interrupt.
[   34.087360] ------------[ cut here ]------------
[   34.091985] WARNING: CPU: 0 PID: 0 at /usr/src/debug/linux-vuplus/3.14.28/drivers/mmc/host/sdhci.c:994 sdhci_send_command+0x798/0xf0c()
[   34.104168] Modules linked in:
[   34.107237] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W    3.14.28-1.12 #1
[   34.114645] [<c0015f70>] (unwind_backtrace) from [<c0011e1c>] (show_stack+0x10/0x14)
[   34.122400] [<c0011e1c>] (show_stack) from [<c059cc54>] (dump_stack+0x6c/0x7c)
[   34.129632] [<c059cc54>] (dump_stack) from [<c059abc0>] (warn_slowpath_common+0x68/0x84)
[   34.137734] [<c059abc0>] (warn_slowpath_common) from [<c0022a7c>] (warn_slowpath_null+0x1c/0x24)
[   34.146532] [<c0022a7c>] (warn_slowpath_null) from [<c045eeb0>] (sdhci_send_command+0x798/0xf0c)
[   34.155329] [<c045eeb0>] (sdhci_send_command) from [<c0460cbc>] (sdhci_timeout_timer+0x74/0xb8)
[   34.164039] [<c0460cbc>] (sdhci_timeout_timer) from [<c002c9b4>] (call_timer_fn.isra.0+0x20/0x7c)
[   34.172921] [<c002c9b4>] (call_timer_fn.isra.0) from [<c002cb5c>] (run_timer_softirq+0x14c/0x218)
[   34.181803] [<c002cb5c>] (run_timer_softirq) from [<c0026e78>] (__do_softirq+0x10c/0x2a8)
[   34.189990] [<c0026e78>] (__do_softirq) from [<c00272a8>] (irq_exit+0xe0/0x118)
[   34.197307] [<c00272a8>] (irq_exit) from [<c000f7e0>] (handle_IRQ+0x44/0x90)
[   34.204365] [<c000f7e0>] (handle_IRQ) from [<c000858c>] (gic_handle_irq+0x2c/0x5c)
[   34.211943] [<c000858c>] (gic_handle_irq) from [<c0012840>] (__irq_svc+0x40/0x50)
[   34.219432] Exception stack(0xc07e3f58 to 0xc07e3fa0)
[   34.224487] 3f40:                                                       ffffffed 179d1000
[   34.232673] 3f60: c07eb3ec 00000000 c07e2000 c05a808c c0829de4 c07ea444 c06bc044 00000001
[   34.240858] 3f80: c07d5628 00000000 d81b0fe0 c07e3fa0 c000fb04 c000fafc 60000113 ffffffff
[   34.249046] [<c0012840>] (__irq_svc) from [<c000fafc>] (arch_cpu_idle+0x2c/0x38)
[   34.256452] [<c000fafc>] (arch_cpu_idle) from [<c005feac>] (cpu_startup_entry+0x74/0x138)
[   34.264639] [<c005feac>] (cpu_startup_entry) from [<c07a2bb8>] (start_kernel+0x40c/0x418)
[   34.272825] [<c07a2bb8>] (start_kernel) from [<00008084>] (0x8084)
[   34.279010] ---[ end trace 70c38a30b36c9d66 ]---
[   34.285718] mmcblk0: error -110 transferring data, sector 81952, nr 8, cmd response 0x0, card status 0x400d00
[   34.295655] end_request: I/O error, dev mmcblk0, sector 81952
[   34.301416] Buffer I/O error on device mmcblk0p4, logical block 1284
[   34.307783] lost page write due to I/O error on mmcblk0p4

Edited by foxbob, 6 February 2024 - 11:41.


Re: Box won't boot. #2 WanWizard

  • PLi® Core member
  • 70,497 posts

+1,810
Excellent

Posted 6 February 2024 - 12:03

The eMMC used as flash has bought it. Or the circuitry connecting it has been damaged. Either way, you get I/O errors when reading it.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Box won't boot. #3 foxbob

  • Senior Member
  • 624 posts

+18
Neutral

Posted 6 February 2024 - 12:37

Can you now use it as a flower stand?There is no way to restore it programmatically?

And if you use the program BroadbandStudio3?


Edited by foxbob, 6 February 2024 - 12:39.


Re: Box won't boot. #4 WanWizard

  • PLi® Core member
  • 70,497 posts

+1,810
Excellent

Posted 6 February 2024 - 12:57

I/O errors are usually hardware errors, either of the storage medium itself, or from the cables / controllers connecting them.

Assuming the eMMC memory chips are soldered on the mainboard, repair, if possible, will require someone skilled.

 

The challenge is also that since you can't get it to boot, you can also not start any tools to further diagnose the problem.

 

If it was a matter of (a few) bad block(s) than a flash would have taken card of that, the eMMC controller would detect and rewrite it. But only if there are still replacement blocks available. Given the fact you tried to flash again, which failed to write the rootfs, I fear the eMMC is damaged.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Box won't boot. #5 foxbob

  • Senior Member
  • 624 posts

+18
Neutral

Posted 6 February 2024 - 13:02

I see, thank you. I will look for an opportunity to purchase duo4k se.



Re: Box won't boot. #6 WanWizard

  • PLi® Core member
  • 70,497 posts

+1,810
Excellent

Posted 6 February 2024 - 13:14

You should be able to get to the bolt prompt by aborting the bootup. Bolt in itself is perfectly capable of booting an OS from a USB stick, I think the old Barry Allen multiboot plugin also utilized that. But I've never done it.

 

You might want to ping @Aliraza63


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Box won't boot. #7 WanWizard

  • PLi® Core member
  • 70,497 posts

+1,810
Excellent

Posted 6 February 2024 - 13:20

Not very hopeful: https://vuplus-suppo...4k-not-booting/


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Box won't boot. #8 foxbob

  • Senior Member
  • 624 posts

+18
Neutral

Posted 6 February 2024 - 13:26

Thank you.



Re: Box won't boot. #9 Dimitrij

  • PLi® Core member
  • 10,324 posts

+350
Excellent

Posted 7 February 2024 - 06:37

Check ignore.update file
Checking usbdisk0:/vuplus/ultimo4k/ignore.update......NO
Check force.update file
Checking usbdisk0:/vuplus/ultimo4k/force.update......NO
bolt update ...Checking usbdisk0:/vuplus/ultimo4k/bolt_auto.bin......NO
Checking usbdisk0:/vuplus/ultimo4k/rootfs.tar.bz2......YES
Checking usbdisk0:/vuplus/ultimo4k/splash_auto.bin......NO
Checking usbdisk0:/vuplus/ultimo4k/kernel_auto.bin......YES
Checking usbdisk0:/vuplus/ultimo4k/reboot.update......YES

For test add file mkpart.update in folder USB -->/vuplus/ultimo4k/ and retry flashing.


Edited by Dimitrij, 7 February 2024 - 06:39.

GigaBlue UHD Quad 4K /Lunix3-4K/Duo 4K


Re: Box won't boot. #10 foxbob

  • Senior Member
  • 624 posts

+18
Neutral

Posted 7 February 2024 - 17:54

I did this, the firmware starts and for about 40 minutes there is a message on the receiver screen - Making File System,then Updating rootfs and nothing happens.

The only thing I can't stop is Bolt.



Re: Box won't boot. #11 Dimitrij

  • PLi® Core member
  • 10,324 posts

+350
Excellent

Posted 7 February 2024 - 20:17

http://vuplus.com/bo...dx=26&pagenum=1


GigaBlue UHD Quad 4K /Lunix3-4K/Duo 4K


Re: Box won't boot. #12 foxbob

  • Senior Member
  • 624 posts

+18
Neutral

Posted 7 February 2024 - 20:42

Without changes.

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2024.02.07 21:38:22 =~=~=~=~=~=~=~=~=~=~=~=
KCPU 0123
BCM74450040
PRID74440040
v1.21
RR:00000003
BFW
seclib-1.9
BBL v1.0.1
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON

single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MEMSYS-ALT
SHMOO 03040100 BLD:exported HW:hpf0_b1p3 V:3.4.1.0
MCB: FLEX
AVS start:status=000000ff
STB: Current voltage=00000396(918)
 temperature=0000926d(37485)
 PV=00000353(851)
 MV=00000397(919)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: !@ ffe0e780 <= ffe0da04 MEMSYS-0 @ f1100000 OK
DDR1: =@ ffe0e780 <= ffe0da04 MEMSYS-1 @ f1180000 OK
DDR2: =@ ffe0e780 <= ffe0da04 MEMSYS-2 @ f1200000 OK
Sdram Scramble OTP = 0x00000001 
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f 
bfw_hash_locked = 0x00000000 
BFW key3 OK, BFW load OK
BFW v4.1.5
COPY CODE... DONE
MICH: disable success
SSBL
SEC: jtag debug status: 000000af
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss  07089dc8
_ebss  070c9528
_end   070c9548
HEAP @ 07100000
STACK @ 09200000
ARCH: CONFIG OK
CLR BSS 07089dc8 to 070c9528 OK
CLR SRAM  OK
CACHE FLUSH OK
CPU CLKSET OK
GO!

[33;1m    ,/   [0m 
[33;1m  ,'/___,[0m BOLT v1.21 v1.21 LOCAL BUILD
[33;1m.'__  ,' [0m (2017-12-15 11:39:14 Vuplus team)
[33;1m   /,'   [0m Copyright (C) 2017 Broadcom
[33;1m  /'     [0m 
[0m
Board: ULTIMO4K
SYS_CTRL: product=7444, family=7445e0, strap=000005b6, 
otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000) 
otp @ 0xf0404034 = 0x00000001: moca2_disable(0x00000001) 
CPU: 4x B15 [420f00f3] 1503 MHz
SCB: 432 MHz
DDR0 @ 1200MHz, DDR1 @ 1200MHz, DDR2 @ 1200MHz
RESET CAUSE: 0x000003 main_chip_input power_on (2 of 21 possible causes)
CS0: SFDP SPI, 4MB, 64kB blocks, 64kB erase block, 256B pages
[31;1mCS1: NAND: unrecognized ID: 0xffffff 0xffffffff[0m
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
RTS2: 0x1201004, 256 clients, ok
BOX MODE: 1
SPLASH: starting
SPLASH BMEM init @ 40000000
SPLASH BMEM init @ 80000000
SPLASH BMEM init @ c0000000
SPLASH: Old format file in flash. Use splash_create_flash_file to create newer format.
Loaded BMP: W=720 H=480
SPLASH: audio not present
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.918V, T=+38.946C, PV=0.851V, MV=0.919V, FW=30333278 [0.3.2.x]
check_tuner_version
i2c_readsw
Tuner Version [0x2]
LCD_Init Complete
boot device name [flash0.bolt]
waiting for usb...
usb: resetting device on bus 4 hub 1 port 1[J


USB: New high speed device connected to bus 4 hub 1 port 1[J


usb: resetting device on bus 4 hub 2 port 1[J


USB: New high speed device connected to bus 4 hub 2 port 1[J

usb: no driver found for 0a5c:bd27

usb: resetting device on bus 4 hub 2 port 2[J


USB: New full speed device connected to bus 4 hub 2 port 2[J


USB: Lower speed devices not supported under high speed hub[J


usb: resetting device on bus 5 hub 1 port 1[J


USB: New high speed device connected to bus 5 hub 1 port 1[J

usb: found Mass-Storage Device 8564:1000

USBMASS: Unit 0 connected[J

done
checking usb
No Priority Usb
checking front key
readFrontKey 0 0
Check ignore.update file
Checking usbdisk0:/vuplus/ultimo4k/ignore.update......NO
Check force.update file
Checking usbdisk0:/vuplus/ultimo4k/force.update......NO
bolt update ...Checking usbdisk0:/vuplus/ultimo4k/bolt_auto.bin......NO
Checking usbdisk0:/vuplus/ultimo4k/rootfs.tar.bz2......YES
Checking usbdisk0:/vuplus/ultimo4k/splash_auto.bin......NO
Checking usbdisk0:/vuplus/ultimo4k/kernel_auto.bin......YES
Checking usbdisk0:/vuplus/ultimo4k/reboot.update......YES
waiting for update key
readFrontKey 0x0
FrontPanel Key : d1, 1
readFrontKey 0xd101
Update
Reading usbdisk0:/vuplus/ultimo4k/bolt_auto.bin: Reading usbdisk0:/vuplus/ultimo4k/bolt_auto.bin:  >> Failed.: File not found
Reading usbdisk0:/vuplus/ultimo4k/splash_auto.bin: Reading usbdisk0:/vuplus/ultimo4k/splash_auto.bin:  >> Failed.: File not found
Reading usbdisk0:/vuplus/ultimo4k/initrd_auto.bin: Reading usbdisk0:/vuplus/ultimo4k/initrd_auto.bin:  >> .....
Done. 8128528 bytes read
Programming...
done. 8128528 bytes written
Reading usbdisk0:/vuplus/ultimo4k/kernel_auto.bin: Reading usbdisk0:/vuplus/ultimo4k/kernel_auto.bin:  >> ...
Done. 4168856 bytes read
Programming...
done. 4168856 bytes written
Checking usbdisk0:/vuplus/ultimo4k/rootfs.tar.bz2......YES
Flashing ..Loader:zimg Filesys:raw Dev:emmcflash0.initrd File:(null) Options:(null)
Reading 8128528 bytes from zImage...........
Starting program at 0x8000 (DTB @ 0x7628000)

32 bit direct boot...
Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.28-1.10 (gdhan@Notebook) (gcc version 4.8.5 (Broadcom stbgcc-4.8-1.4) ) #35 SMP Wed Feb 8 19:44:16 KST 2017
[    0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c7387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine model: ULTIMO4K
[    0.000000] moving dtb from 0x0000000007628000 to 0x0000000000bda684
[    0.000000] bmem: Reserved 768 MiB at 0x0000000010000000
[    0.000000] bmem: Reserved 1024 MiB at 0x0000000040000000
[    0.000000] bmem: Reserved 1020 MiB at 0x0000000080000000
[    0.000000] cma: Reserved 16 MiB at 0x000000000f000000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] MCP: Enabling write pairing
[    0.000000] PERCPU: Embedded 8 pages/cpu @cd7b1000 s8704 r8192 d15872 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 785920
[    0.000000] Kernel command line: 
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 208500K/3145728K available (5624K kernel code, 287K rwdata, 1772K rodata, 4188K init, 226K bss, 2920844K reserved, 16384K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0741460   (7398 kB)
[    0.000000]       .init : 0xc0742000 - 0xc0b59200   (4189 kB)
[    0.000000]       .data : 0xc0b5a000 - 0xc0ba1e08   ( 288 kB)
[    0.000000]        .bss : 0xc0ba1e10 - 0xc0bda684   ( 227 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc403000, parent irq: 94)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc3e1000, parent irq: 64)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc410640, parent irq: 96)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc4d1200, parent irq: 48)
[    0.000000] Architected cp15 timer(s) running at 27.00MHz (virt).
[    0.000004] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 2545165795328ns
[    0.000010] Switching to timer-based delay loop
[    0.000285] Console: colour dummy device 80x30
[    0.000306] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
[    0.000313] pid_max: default: 32768 minimum: 301
[    0.000415] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000422] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.005827] CPU: Testing write buffer coherency: ok
[    0.006028] CPU0: update cpu_power 1024
[    0.006035] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.006165] Setting up static identity map for 0x55a340 - 0x55a398
[    0.008675] CPU1: Booted secondary processor
[    0.008692] CPU1: update cpu_power 1024
[    0.008695] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.009409] CPU2: Booted secondary processor
[    0.009420] CPU2: update cpu_power 1024
[    0.009423] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.010096] CPU3: Booted secondary processor
[    0.010107] CPU3: update cpu_power 1024
[    0.010110] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.010190] Brought up 4 CPUs
[    0.010208] SMP: Total of 4 processors activated.
[    0.010213] CPU: All CPU(s) started in SVC mode.
[    0.010562] devtmpfs: initialized
[    0.014146] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
[    0.015142] regulator-dummy: no parameters
[    0.015327] NET: Registered protocol family 16
[    0.016029] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.016814] cpuidle: using governor ladder
[    0.016820] cpuidle: using governor menu
[    0.019900] irq: no irq domain found for /rdb/interrupt-controller@f040a780 !
[    0.020040] irq: no irq domain found for /rdb/interrupt-controller@f0417280 !
[    0.023923] irq: no irq domain found for /rdb/interrupt-controller@f03e1a00 !
[    0.024198] syscon f0404000.syscon: regmap [mem 0xf0404000-0xf040451b] registered
[    0.025020] syscon f0404100.syscon: regmap [mem 0xf0404100-0xf040415b] registered
[    0.025182] syscon f040415c.syscon: regmap [mem 0xf040415c-0xf040419b] registered
[    0.025324] syscon f0410700.syscon: regmap [mem 0xf0410700-0xf041070b] registered
[    0.025463] syscon f041070c.syscon: regmap [mem 0xf041070c-0xf0410713] registered
[    0.025619] syscon f1101004.syscon: regmap [mem 0xf1101004-0xf1101403] registered
[    0.025761] syscon f1181004.syscon: regmap [mem 0xf1181004-0xf1181403] registered
[    0.025909] syscon f1201004.syscon: regmap [mem 0xf1201004-0xf1201403] registered
[    0.026039] syscon f0404080.syscon: regmap [mem 0xf0404080-0xf0404083] registered
[    0.026176] syscon f04040a4.syscon: regmap [mem 0xf04040a4-0xf04040a7] registered
[    0.026314] syscon f03e0154.syscon: regmap [mem 0xf03e0154-0xf03e0157] registered
[    0.026452] syscon f03e0354.syscon: regmap [mem 0xf03e0354-0xf03e0357] registered
[    0.026589] syscon f03e0400.syscon: regmap [mem 0xf03e0400-0xf03e0403] registered
[    0.027159] irq: no irq domain found for /rdb/interrupt-controller@f0417280 !
[    0.027704] syscon f03e2400.syscon: regmap [mem 0xf03e2400-0xf03e27ff] registered
[    0.027957] syscon f0452000.syscon: regmap [mem 0xf0452000-0xf04520ff] registered
[    0.028284] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.028290] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.028418] Broadcom Brahma-B15 readahead cache at: 0xfc3e2478
[    0.041069] bio: create slab <bio-0> at 0
[    0.041382] brcmstb-gpio f040a700.gpio: Couldn't get IRQ. Enable CONFIG_BCM7120_L2_IRQ if you want GPIO interrupt support
[    0.041405] brcmstb-gpio f040a700.gpio: Registered 4 banks (GPIO(s): 0-127)
[    0.041434] brcmstb-gpio f04172c0.gpio: Couldn't get IRQ. Enable CONFIG_BCM7120_L2_IRQ if you want GPIO interrupt support
[    0.041448] brcmstb-gpio f04172c0.gpio: Registered 2 banks (GPIO(s): 128-191)
[    0.042121] SCSI subsystem initialized
[    0.042735] usbcore: registered new interface driver usbfs
[    0.042812] usbcore: registered new interface driver hub
[    0.042937] usbcore: registered new device driver usb
[    0.043138] Linux video capture interface: v2.00
[    0.043252] pps_core: LinuxPPS API ver. 1 registered
[    0.043256] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.043313] PTP clock support registered
[    0.043792] Advanced Linux Sound Architecture Driver Initialized.
[    0.144839] brcm-pci f0460000.pcie: link down
[    0.244900] brcm-pci f0490000.pcie: link down
[    0.244949] Switched to clocksource arch_sys_counter
[    0.254140] thermal thermal_zone0: failed to read out thermal zone 0
[    0.254230] NET: Registered protocol family 2
[    0.254588] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.254605] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.254629] TCP: Hash tables configured (established 2048 bind 2048)
[    0.254668] TCP: reno registered
[    0.254675] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.254688] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.254816] NET: Registered protocol family 1
[    0.255022] RPC: Registered named UNIX socket transport module.
[    0.255027] RPC: Registered udp transport module.
[    0.255031] RPC: Registered tcp transport module.
[    0.255034] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.368923] hw perfevents: enabled with ARMv7 Cortex-A15 PMU driver, 7 counters available
[    0.370389] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.371246] bounce pool size: 64 pages
[    0.371607] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.371811] NFS: Registering the id_resolver key type
[    0.371836] Key type id_resolver registered
[    0.371841] Key type id_legacy registered
[    0.371851] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.371864] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.371973] fuse init (API version 7.22)
[    0.372365] msgmni has been set to 439
[    0.372840] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.372847] io scheduler noop registered
[    0.372851] io scheduler deadline registered
[    0.372871] io scheduler cfq registered (default)
[    0.373105] brcm-gisb-arb f0400000.gisb-arb: registered mem: fc400000, irqs: 258, 259
[    0.403540] brcmstb_memc f1102000.memc-ddr: registered
[    0.403567] brcmstb_memc f1182000.memc-ddr: registered
[    0.403594] brcmstb_memc f1202000.memc-ddr: registered
[    0.403813] brcm-waketimer f0417580.waketimer: registered, with irq 260
[    0.459387] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.461193] f040ab00.serial: ttyS0 at MMIO 0xf040ab00 (irq = 107, base_baud = 5062500) is a 16550A
[    1.301951] console [ttyS0] enabled
[    1.306076] f040ab40.serial: ttyS1 at MMIO 0xf040ab40 (irq = 108, base_baud = 5062500) is a 16550A
[    1.315613] f040ab80.serial: ttyS2 at MMIO 0xf040ab80 (irq = 109, base_baud = 5062500) is a 16550A
[    1.330664] brd: module loaded
[    1.336598] loop: module loaded
[    1.340457] ahci brcmstb-ahci.0: can't get clock
[    1.345176] ahci brcmstb-ahci.0: SSS flag set, parallel bus scan disabled
[    1.362965] ahci brcmstb-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[    1.371596] ahci brcmstb-ahci.0: flags: 64bit ncq sntf stag pm clo pmp slum part 
[    1.381024] scsi0 : ahci_platform
[    1.384678] scsi1 : ahci_platform
[    1.388228] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 62
[    1.396163] ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x180 irq 62
[    1.405388] spi_brcmstb f03e3400.spi: 1-lane output, 3-byte address
[    1.411781] spi_brcmstb f03e3400.spi: master is unqueued, this is deprecated
[    1.419111] m25p80 spi32766.0: found mx25l3255e, expected m25p80
[    1.425137] m25p80 spi32766.0: mx25l3255e (4096 Kbytes)
[    1.430393] 5 ofpart partitions found on MTD device spi32766.0
[    1.436237] Creating 5 MTD partitions on "spi32766.0":
[    1.441389] 0x000000000000-0x000000200000 : "flash0.bolt"
[    1.447509] 0x000000200000-0x000000210000 : "flash0.macadr"
[    1.453743] 0x000000210000-0x000000220000 : "flash0.nvram"
[    1.459892] 0x000000220000-0x000000230000 : "flash0.devtree"
[    1.466234] 0x000000000000-0x000000400000 : "flash0"
[    1.472922] libphy: Fixed MDIO Bus: probed
[    1.479484] libphy: unimac MII bus: probed
[    1.487831] unimac-mdio f0b403c0.mdio: Broadcom UniMAC MDIO bus at 0xfcb403c0
[    1.495836] brcm-systemport f04a0000.ethernet: Broadcom SYSTEMPORTv 1.00 at 0xfc4a0000 (irqs: 54, 55, TXQs: 32, RXQs: 1)
[    1.509410] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.515261] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.515965] ata1: SATA link down (SStatus 0 SControl 300)
[    1.526717] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[    1.534223] usbcore: registered new interface driver pegasus
[    1.539988] usbcore: registered new interface driver asix
[    1.545469] usbcore: registered new interface driver ax88179_178a
[    1.551651] usbcore: registered new interface driver cdc_ether
[    1.557596] usbcore: registered new interface driver cdc_ncm
[    1.563764] xhci-brcm: xHCI BRCM driver
[    1.567698] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[    1.573543] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1
[    1.581625] xhci-brcm f0471000.xhci_v2: irq 115, io mem 0xf0471000
[    1.588372] hub 1-0:1.0: USB hub found
[    1.592154] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    1.599431] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[    1.605248] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2
[    1.613589] hub 2-0:1.0: USB hub found
[    1.617370] hub 2-0:1.0: 2 ports detected
[    1.621787] ehci-brcm: EHCI BRCM driver
[    1.625704] ehci-brcm f0470300.ehci_v2: EHCI Host Controller
[    1.631526] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3
[    1.641957] ata2: SATA link down (SStatus 0 SControl 300)
[    1.649477] ehci-brcm f0470300.ehci_v2: irq 111, io mem 0xf0470300
[    1.660958] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.667655] hub 3-0:1.0: USB hub found
[    1.671441] hub 3-0:1.0: 1 port detected
[    1.675596] ehci-brcm f0470500.ehci_v2: EHCI Host Controller
[    1.681420] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4
[    1.699371] ehci-brcm f0470500.ehci_v2: irq 112, io mem 0xf0470500
[    1.710958] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.717639] hub 4-0:1.0: USB hub found
[    1.721417] hub 4-0:1.0: 1 port detected
[    1.725562] ehci-brcm f0480300.ehci_v2: EHCI Host Controller
[    1.731378] ehci-brcm f0480300.ehci_v2: new USB bus registered, assigned bus number 5
[    1.749310] ehci-brcm f0480300.ehci_v2: irq 117, io mem 0xf0480300
[    1.760958] ehci-brcm f0480300.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.767611] hub 5-0:1.0: USB hub found
[    1.771392] hub 5-0:1.0: 1 port detected
[    1.775570] ehci-brcm f0480500.ehci_v2: EHCI Host Controller
[    1.781382] ehci-brcm f0480500.ehci_v2: new USB bus registered, assigned bus number 6
[    1.799317] ehci-brcm f0480500.ehci_v2: irq 118, io mem 0xf0480500
[    1.810957] ehci-brcm f0480500.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.817611] hub 6-0:1.0: USB hub found
[    1.821390] hub 6-0:1.0: 1 port detected
[    1.825681] ohci-brcm: OHCI BRCM driver
[    1.829592] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller
[    1.835412] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 7
[    1.843293] ohci-brcm f0470400.ohci_v2: irq 113, io mem 0xf0470400
[    1.904409] hub 7-0:1.0: USB hub found
[    1.908190] hub 7-0:1.0: 1 port detected
[    1.912326] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller
[    1.918141] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 8
[    1.926030] ohci-brcm f0470600.ohci_v2: irq 114, io mem 0xf0470600
[    1.987409] hub 8-0:1.0: USB hub found
[    1.991192] hub 8-0:1.0: 1 port detected
[    1.995337] ohci-brcm f0480400.ohci_v2: BRCM OHCI controller
[    2.001156] ohci-brcm f0480400.ohci_v2: new USB bus registered, assigned bus number 9
[    2.009037] ohci-brcm f0480400.ohci_v2: irq 119, io mem 0xf0480400
[    2.070409] hub 9-0:1.0: USB hub found
[    2.074188] hub 9-0:1.0: 1 port detected
[    2.076976] usb 5-1: new high-speed USB device number 2 using ehci-brcm
[    2.084954] ohci-brcm f0480600.ohci_v2: BRCM OHCI controller
[    2.090772] ohci-brcm f0480600.ohci_v2: new USB bus registered, assigned bus number 10
[    2.098751] ohci-brcm f0480600.ohci_v2: irq 120, io mem 0xf0480600
[    2.160416] hub 10-0:1.0: USB hub found
[    2.164283] hub 10-0:1.0: 1 port detected
[    2.168619] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.175169] ehci-pci: EHCI PCI platform driver
[    2.179701] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.185908] ohci-pci: OHCI PCI platform driver
[    2.190671] usbcore: registered new interface driver usb-storage
[    2.197347] hub 5-1:1.0: USB hub found
[    2.201282] hub 5-1:1.0: 4 ports detected
[    2.201300] mousedev: PS/2 mouse device common for all mice
[    2.211208] i2c /dev entries driver
[    2.214927] gspca_main: v2.14.0 registered
[    2.219366] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor driver
[    2.227133] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    2.232979] sdhci: Secure Digital Host Controller Interface driver
[    2.239174] sdhci: Copyright(c) Pierre Ossman
[    2.243542] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.250320] mmc0: no vqmmc regulator found
[    2.254429] mmc0: no vmmc regulator found
[    2.288960] mmc0: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA
[    2.298797] usbcore: registered new interface driver usbhid
[    2.306397] usbhid: USB HID core driver
[    2.310859] TCP: cubic registered
[    2.314191] NET: Registered protocol family 17
[    2.319373] Distributed Switch Architecture driver version 0.1
[    2.325268] eth0[0]: detected a Broadcom Starfighter 2 switch
[    2.331221] Starfighter 2 top: 4.00, core: 2.00 base: 0xfcb00000, IRQs: 56, 57
[    2.338899] libphy: dsa slave smi: probed
[    2.372599] mmc0: BKOPS_EN bit is not set
[    2.382850] mmc0: new high speed MMC card at address 0001
[    2.388540] mmcblk0: mmc0:0001 4FPD3R 3.64 GiB 
[    2.393180] mmcblk0boot0: mmc0:0001 4FPD3R partition 1 4.00 MiB
[    2.399208] mmcblk0boot1: mmc0:0001 4FPD3R partition 2 4.00 MiB
[    2.399953] f0b403c0.mdio:05: Broadcom BCM7445 PHY revision: 0x10, patch: 3
[    2.412227] mmcblk0rpmb: mmc0:0001 4FPD3R partition 3 512 KiB
[    2.421073]  mmcblk0: p1 p2 p3 p4
[    2.427197]  mmcblk0boot1: unknown partition table
[    2.432725]  mmcblk0boot0: unknown partition table
[    2.491031] usb 5-1.1: new high-speed USB device number 3 using ehci-brcm
[    2.633138] attached PHY at address 5 [Broadcom BCM7445]
[    2.638470] eth0: error -17 registering interface eth0
[    2.643627] eth0[0]: can't create dsa slave device for port 0(eth0)
[    2.650096] Key type dns_resolver registered
[    2.654393] Registering SWP/SWPB emulation handler
[    2.658032] usb 5-1.2: new full-speed USB device number 4 using ehci-brcm
[    2.666676] regulator-dummy: disabling
[    2.673747] ALSA device list:
[    2.676731]   No soundcards found.
[    2.683924] Freeing unused kernel memory: 4188K (c0742000 - c0b59000)

starting pid 1286, tty '': '/etc/init.d/rcS'
Mounting virtual filesystems
* WARNING: THIS STB CONTAINS GPLv3 SOFTWARE
* GPLv3 programs must be removed in order to enable security.
* See: http://www.gnu.org/licenses/gpl-faq.html#Tivoization
Configuring eth0 interface
Configuring lo interface
Starting network services

starting pid 1331, tty '': '/bin/cttyhack /bin/sh -l'
# [    2.950973] usb 6-1: new high-speed USB device number 2 using ehci-brcm
[    3.072976] usb-storage 6-1:1.0: USB Mass Storage device detected
[    3.080845] scsi2 : usb-storage 6-1:1.0
[    4.088735] scsi 2:0:0:0: Direct-Access     JetFlash Transcend 8GB    1.00 PQ: 0 ANSI: 6
[    4.098623] sd 2:0:0:0: [sda] 15433728 512-byte logical blocks: (7.90 GB/7.35 GiB)
[    4.106342] sd 2:0:0:0: Attached scsi generic sg0 type 0
[    4.112117] sd 2:0:0:0: [sda] Write Protect is off
[    4.117356] sd 2:0:0:0: [sda] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
[    4.134375]  sda: sda1 sda2
[    4.140110] sd 2:0:0:0: [sda] Attached SCSI removable disk
[    4.199715] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[    4.227457] FAT-fs (sda2): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[    4.790088] libphy: fixed-0:00 - Link is Up - 1000/Full
[    5.539057] random: sgdisk urandom read with 77 bits of entropy available
[   15.583962] mmc0: Timeout waiting for hardware interrupt.
[   15.591375] ------------[ cut here ]------------
[   15.596007] WARNING: CPU: 0 PID: 0 at drivers/mmc/host/sdhci.c:994 sdhci_send_command+0xd74/0xf18()
[   15.605062] Modules linked in: vfd_proc(O)
[   15.609191] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G           O 3.14.28-1.10 #35
[   15.616696] [<c0015c4c>] (unwind_backtrace) from [<c0011f60>] (show_stack+0x10/0x14)
[   15.624453] [<c0011f60>] (show_stack) from [<c05553c0>] (dump_stack+0x80/0x90)
[   15.631688] [<c05553c0>] (dump_stack) from [<c002288c>] (warn_slowpath_common+0x6c/0x88)
[   15.639792] [<c002288c>] (warn_slowpath_common) from [<c0022944>] (warn_slowpath_null+0x1c/0x24)
[   15.648590] [<c0022944>] (warn_slowpath_null) from [<c0455164>] (sdhci_send_command+0xd74/0xf18)
[   15.657389] [<c0455164>] (sdhci_send_command) from [<c045571c>] (sdhci_timeout_timer+0x74/0xb8)
[   15.666102] [<c045571c>] (sdhci_timeout_timer) from [<c002cd2c>] (call_timer_fn.isra.33+0x24/0x88)
[   15.675074] [<c002cd2c>] (call_timer_fn.isra.33) from [<c002cf24>] (run_timer_softirq+0x194/0x210)
[   15.684044] [<c002cf24>] (run_timer_softirq) from [<c002696c>] (__do_softirq+0x10c/0x250)
[   15.692232] [<c002696c>] (__do_softirq) from [<c0026d40>] (irq_exit+0xb4/0xfc)
[   15.699464] [<c0026d40>] (irq_exit) from [<c000f604>] (handle_IRQ+0x44/0x90)
[   15.706522] [<c000f604>] (handle_IRQ) from [<c00085a4>] (gic_handle_irq+0x2c/0x5c)
[   15.714102] [<c00085a4>] (gic_handle_irq) from [<c0012a80>] (__irq_svc+0x40/0x50)
[   15.721592] Exception stack(0xc0b5bf58 to 0xc0b5bfa0)
[   15.726649] bf40:                                                       ffffffed 0cc5a000
[   15.734835] bf60: c0b632a4 00000000 c0b6249c c0b5a000 c0b62420 c0b92966 c055d00c c0b5a000
[   15.743021] bf80: c0b92966 c0b5a000 00000020 c0b5bfa0 c000f958 c000f950 60000013 ffffffff
[   15.751209] [<c0012a80>] (__irq_svc) from [<c000f950>] (arch_cpu_idle+0x2c/0x38)
[   15.758618] [<c000f950>] (arch_cpu_idle) from [<c006025c>] (cpu_startup_entry+0xfc/0x140)
[   15.766810] [<c006025c>] (cpu_startup_entry) from [<c0742bc0>] (start_kernel+0x418/0x424)
[   15.774997] ---[ end trace d9819cd89e2b3bab ]---
[   15.781734] mmcblk0: error -110 transferring data, sector 7634904, nr 40, cmd response 0x0, card status 0x400d00
[   15.791935] end_request: I/O error, dev mmcblk0, sector 7634904
[   15.797871] Buffer I/O error on device mmcblk0, logical block 954363
[   15.804237] lost page write due to I/O error on mmcblk0
[   15.809484] end_request: I/O error, dev mmcblk0, sector 7634912
[   15.815419] Buffer I/O error on device mmcblk0, logical block 954364
[   15.821785] lost page write due to I/O error on mmcblk0
[   15.827028] end_request: I/O error, dev mmcblk0, sector 7634920
[   15.832960] Buffer I/O error on device mmcblk0, logical block 954365
[   15.839326] lost page write due to I/O error on mmcblk0
[   15.844566] end_request: I/O error, dev mmcblk0, sector 7634928
[   15.850499] Buffer I/O error on device mmcblk0, logical block 954366
[   15.856863] lost page write due to I/O error on mmcblk0
[   15.862103] end_request: I/O error, dev mmcblk0, sector 7634936
[   15.868035] Buffer I/O error on device mmcblk0, logical block 954367
[   15.874400] lost page write due to I/O error on mmcblk0
[   16.884381]  mmcblk0: p1 p2 p3 p4
[   18.275259] random: nonblocking pool is initialized
[   28.383951] mmc0: Timeout waiting for hardware interrupt.
[   28.391369] ------------[ cut here ]------------
[   28.396004] WARNING: CPU: 0 PID: 0 at drivers/mmc/host/sdhci.c:994 sdhci_send_command+0xd74/0xf18()
[   28.405059] Modules linked in: vfd_proc(O)
[   28.409192] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W  O 3.14.28-1.10 #35
[   28.416697] [<c0015c4c>] (unwind_backtrace) from [<c0011f60>] (show_stack+0x10/0x14)
[   28.424454] [<c0011f60>] (show_stack) from [<c05553c0>] (dump_stack+0x80/0x90)
[   28.431690] [<c05553c0>] (dump_stack) from [<c002288c>] (warn_slowpath_common+0x6c/0x88)
[   28.439793] [<c002288c>] (warn_slowpath_common) from [<c0022944>] (warn_slowpath_null+0x1c/0x24)
[   28.448591] [<c0022944>] (warn_slowpath_null) from [<c0455164>] (sdhci_send_command+0xd74/0xf18)
[   28.457390] [<c0455164>] (sdhci_send_command) from [<c045571c>] (sdhci_timeout_timer+0x74/0xb8)
[   28.466102] [<c045571c>] (sdhci_timeout_timer) from [<c002cd2c>] (call_timer_fn.isra.33+0x24/0x88)
[   28.475074] [<c002cd2c>] (call_timer_fn.isra.33) from [<c002cf24>] (run_timer_softirq+0x194/0x210)
[   28.484045] [<c002cf24>] (run_timer_softirq) from [<c002696c>] (__do_softirq+0x10c/0x250)
[   28.492233] [<c002696c>] (__do_softirq) from [<c0026d40>] (irq_exit+0xb4/0xfc)
[   28.499465] [<c0026d40>] (irq_exit) from [<c000f604>] (handle_IRQ+0x44/0x90)
[   28.506523] [<c000f604>] (handle_IRQ) from [<c00085a4>] (gic_handle_irq+0x2c/0x5c)
[   28.514103] [<c00085a4>] (gic_handle_irq) from [<c0012a80>] (__irq_svc+0x40/0x50)
[   28.521593] Exception stack(0xc0b5bf58 to 0xc0b5bfa0)
[   28.526650] bf40:                                                       ffffffed 0cc5a000
[   28.534836] bf60: c0b632a4 00000000 c0b6249c c0b5a000 c0b62420 c0b92966 c055d00c c0b5a000
[   28.543023] bf80: c0b92966 c0b5a000 00000020 c0b5bfa0 c000f958 c000f950 600f0013 ffffffff
[   28.551214] [<c0012a80>] (__irq_svc) from [<c000f950>] (arch_cpu_idle+0x2c/0x38)
[   28.558622] [<c000f950>] (arch_cpu_idle) from [<c006025c>] (cpu_startup_entry+0xfc/0x140)
[   28.566814] [<c006025c>] (cpu_startup_entry) from [<c0742bc0>] (start_kernel+0x418/0x424)
[   28.575001] ---[ end trace d9819cd89e2b3bac ]---
[   28.581746] mmcblk0: error -110 transferring data, sector 71680, nr 8, cmd response 0x0, card status 0x400d00
[   28.591687] end_request: I/O error, dev mmcblk0, sector 71680
[   28.597449] Buffer I/O error on device mmcblk0p4, logical block 0
[   28.603555] lost page write due to I/O error on mmcblk0p4



1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users