Jump to content


Photo

openPli 9,0 and 8,3 PIP problem on Gigablue UE UHD 4k

Started by Fuat S ASLI, 06 Jun 2024 12:39

  • Please log in to reply
4 replies to this topic

#1 Fuat S ASLI

  • New Member
  • 3 posts

0
Neutral

Posted 6 June 2024 - 12:39

In the first PIP there is no problem. Later PIP is not done on the current channel; instead, previous channel is PIP ed.
Enigma restart temporarily solves the problem. Swap PIP, move PIP is OKEY.
It was OK at the start, for months. Later I had to change antenna and couldn't tune first. SNRs was bad, couln't tune to same channels.
I think the problem started then. Now I fixed the antenna, SNR s are OKEY.
Re scanned the channels, deleting previous, but problem is NOT solved!

Re: openPli 9,0 and 8,3 PIP problem on Gigablue UE UHD 4k #2 Dimitrij

  • PLi® Core member
  • 10,379 posts

+354
Excellent

Posted 6 June 2024 - 13:36

"User interface"

option "Remember last service in PiP"


GigaBlue UHD Quad 4K /Lunix3-4K/Duo 4K

Re: openPli 9,0 and 8,3 PIP problem on Gigablue UE UHD 4k #3 Fuat S ASLI

  • New Member
  • 3 posts

0
Neutral

Posted 6 June 2024 - 15:59

"User interface"

option "Remember last service in PiP"

I remember this, but it is in openATV. There is NONE in openPLİ. Thanks ..


Re: openPli 9,0 and 8,3 PIP problem on Gigablue UE UHD 4k #4 littlesat

  • PLi® Core member
  • 57,427 posts

+708
Excellent

Posted 6 June 2024 - 16:21

Are you in expert mode the option should be there as I made it myself long time ago.

WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W

Re: openPli 9,0 and 8,3 PIP problem on Gigablue UE UHD 4k #5 40H3X

  • Forum Moderator
    PLi® Contributor
  • 5,967 posts

+191
Excellent

Posted 7 June 2024 - 11:11

As for some reason @Fuat S ASLI could not post a reply and send a Admin Report, so I will post his reply:

 

@Fuat S ASL:

NOT: this is an answer to a perfect solution to PIP problem (I cannot reply to messages!).

TO : Dimitrij and littlesat on 06 Jun 2024
"menu>setup>system>Expert settings>User Mode" : changed to "Expert" (from advanced)
"menu>setup>system>GUI settings>User Interface" : changed to "NON" (from no timeout)
Now the problem is resolved. I tried for days to fix this but could'nt.
Regards ....


Hardware: Vu+ Uno 4K SE - Vu+ Duo 4K  - Fuba 78 cm - Tripleblock LNB Quad 19.2/23.5/28.2 - DS918+
Software : OpenPLi - OSCam - Settings van Hans - Autotimer - EPGImport

---------------------------------------------------------------------------------------------------------------------------------------

Remember: Upvote with the rep_up.png button for any user/post you find to be helpful, informative, or deserving of recognition!

---------------------------------------------------------------------------------------------------------------------------------------

Many answers to your question can be found in our new and improved wiki

Note: I do not provide support via PM !.

Back to [EN] Enduser support

2 user(s) are reading this topic

0 members, 2 guests, 0 anonymous users

  1. Forums
  2. → PLi® Support
  3. → [EN] Enduser support