23 replies to this topic

[dalmidog]

hi,

Nach dem Update heute 15.12.2011, bootet meine ET9200 nicht mehr hoch. D.h. der Pinguin ist noch sichtbar, aber danach bleibt das Bild Schwarz. Kann auch nichts ausführen.
Telnet funktioniert noch, und habe auch nochmal ein "opkg update && opkg upgrade" ausgeführt, aber auch das brachte bis jetzt nichts.

root@et9x00:~# opkg update && opkg upgrade
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/3rd-party/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/3rd-party/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-3rd-party.
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/all/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/all/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-all.
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/et9x00/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/et9x00/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-et9x00.
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/mipsel/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/mipsel/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-mipsel.
root@et9x00:~# opkg update && opkg upgrade
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/3rd-party/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/3rd-party/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-3rd-party.
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/all/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/all/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-all.
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/et9x00/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/et9x00/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-et9x00.
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/mipsel/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/mipsel/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-mipsel.

[Hump]

Kann ich nicht bestätigen. Box bootet nach dem heutigen Update einwandfrei. Keine Probleme.

[Frogman]

Auch bei mir keinerlei Probleme nach dem Update... - weder Fehlermeldungen beim Update selbst noch beim Booten danach.

[nobody9]

Hallo dalmidog,

schau mal nach ob bei dir die DVB Module geladen werden. Auf den telnet console lsmod.
Hatte bei mir unter /etc eine datei modules in dem ein falscher parameter beim dvb Module drin stand, dadurch bekammen die Module beim laden einen Segfault.

nobody9

hi,

Nach dem Update heute 15.12.2011, bootet meine ET9200 nicht mehr hoch. D.h. der Pinguin ist noch sichtbar, aber danach bleibt das Bild Schwarz. Kann auch nichts ausführen.
Telnet funktioniert noch, und habe auch nochmal ein "opkg update && opkg upgrade" ausgeführt, aber auch das brachte bis jetzt nichts.

root@et9x00:~# opkg update && opkg upgrade
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/3rd-party/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/3rd-party/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-3rd-party.
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/all/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/all/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-all.
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/et9x00/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/et9x00/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-et9x00.
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/mipsel/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/mipsel/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-mipsel.
root@et9x00:~# opkg update && opkg upgrade
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/3rd-party/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/3rd-party/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-3rd-party.
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/all/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/all/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-all.
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/et9x00/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/et9x00/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-et9x00.
Downloading http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/mipsel/Packages.gz.
Inflating http://downloads.pli-images.org/feeds/openpli-2.1/et9x00/mipsel/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-mipsel.

[dalmidog]

lsmod ergibt folgendes

root@et9x00:~# lsmod
Module				  Size  Used by
zd1211rw			   55901  0
usbserial			  30999  0
rtl8192cu			  95190  0
rtl8192c_common	    56264  1 rtl8192cu
rtlwifi			    98198  1 rtl8192cu
rtl8187			    54063  0
rt73usb			    24424  0
rt2800usb			  13121  0
rt2800lib			  45452  1 rt2800usb
rt2500usb			  18201  0
rt2x00usb			  10969  3 rt73usb,rt2800usb,rt2500usb
rt2x00lib			  40230  5 rt73usb,rt2800usb,rt2800lib,rt2500usb,rt2x00usb
r8712u			    173309  0
ipv6				  340622  14
carl9170			   85327  0
ath9k_htc			  63467  0
mac80211			  222236  10 zd1211rw,rtl8192cu,rtl8192c_common,rtlwifi,rtl8187,rt2800lib,rt2x00usb,rt2x00lib,carl9170,ath9k_htc
ath9k_common		    1704  1 ath9k_htc
ath9k_hw			  352683  2 ath9k_htc,ath9k_common
ath				    17058  4 carl9170,ath9k_htc,ath9k_common,ath9k_hw
modloader2			 33264  0
modloader			  22329  0
tpm					 7873  2 modloader2,modloader

[dalmidog]

unter /etc habe ich und drin stehen, alle sind vom 15.12.2011:

modules

### This file is automatically generated by update-modules"
#
# Please do not edit this file directly. If you want to change or add
# anything please take a look at the files in /etc/modutils and read
# the manpage for update-modules.
#
### update-modules: start processing /etc/modutils/_et9x00
tpm
modloader
modloader2
dvb use_advanced_remote=0
### update-modules: end processing /etc/modutils/_et9x00
### update-modules: start processing /etc/modutils/ath9k_htc
ath9k_htc
### update-modules: end processing /etc/modutils/ath9k_htc
### update-modules: start processing /etc/modutils/carl9170
carl9170
### update-modules: end processing /etc/modutils/carl9170
### update-modules: start processing /etc/modutils/ipv6
ipv6
### update-modules: end processing /etc/modutils/ipv6
### update-modules: start processing /etc/modutils/r8712u
r8712u
### update-modules: end processing /etc/modutils/r8712u
### update-modules: start processing /etc/modutils/rt2500usb
rt2500usb
### update-modules: end processing /etc/modutils/rt2500usb
### update-modules: start processing /etc/modutils/rt2800usb
rt2800usb
### update-modules: end processing /etc/modutils/rt2800usb
### update-modules: start processing /etc/modutils/rt73usb
rt73usb
### update-modules: end processing /etc/modutils/rt73usb
### update-modules: start processing /etc/modutils/rtl8187
rtl8187
### update-modules: end processing /etc/modutils/rtl8187
### update-modules: start processing /etc/modutils/rtl8192cu
rtl8192cu
### update-modules: end processing /etc/modutils/rtl8192cu
### update-modules: start processing /etc/modutils/usbserial
usbserial
### update-modules: end processing /etc/modutils/usbserial
### update-modules: start processing /etc/modutils/zd1211rw
zd1211rw
### update-modules: end processing /etc/modutils/zd1211rw
 

modules.conf

### This file is automatically generated by update-modules"
#
# Please do not edit this file directly. If you want to change or add
# anything please take a look at the files in /etc/modutils and read
# the manpage for update-modules.
#

modules.conf.old

### This file is automatically generated by update-modules"
#
# Please do not edit this file directly. If you want to change or add
# anything please take a look at the files in /etc/modutils and read
# the manpage for update-modules.
#

Edited by dalmidog, 15 December 2011 - 13:24.

[Dimitrij]

Just edit the file /etc/modutils/_et9x00 like this:

tpm
modloader
modloader2
dvb

then give the command:

update-modules

and reboot.

Dann entfernen Sie das Plug-in-Plugins dvboptions

Edited by Dima73, 15 December 2011 - 13:31.

[dalmidog]

habe ich gemacht aber die Box startet nicht.

[Dimitrij]

In den Telnet-Befehl:
update-modules

Und es gibt, zeigen die Ausgabe
cat /etc/modutils/_et9x00

[dalmidog]

root@et9x00:~# update-modules

root@et9x00:~# cat /etc/modutils/_et9x00

tpm

modloader

modloader2

dvbroot@et9x00:~#

[Dimitrij]

tpm
modloader
modloader2
dvb

In den Telnet-Befehl:
update-modules
reboot

Edited by Dima73, 15 December 2011 - 14:31.

[nobody9]

es fehlt das return nach dem dvb.

und du solltest

update-modules -f

aufrufen sonst meint er es ist schon aktuell.

Edited by nobody9, 15 December 2011 - 14:32.

[daddelfalk]

Hi,

this Option is no illegal with latest ET-Drivers:

use_advanced_remote=0

so remove it from /etc/modutils/_et9x00 File

and do Command: update-modules

on telnet, after that reboot your STB.

Edited by daddelfalk, 15 December 2011 - 14:32.

[dalmidog]

zur Zeit steht das drin.

/etc/modutils/_et9x00

tpm
modloader
modloader2
dvb

/etc/modules

### This file is automatically generated by update-modules"
#
# Please do not edit this file directly. If you want to change or add
# anything please take a look at the files in /etc/modutils and read
# the manpage for update-modules.
#
### update-modules: start processing /etc/modutils/_et9x00
tpm
modloader
modloader2
dvb
### update-modules: end processing /etc/modutils/_et9x00
### update-modules: start processing /etc/modutils/ath9k_htc
ath9k_htc
### update-modules: end processing /etc/modutils/ath9k_htc
### update-modules: start processing /etc/modutils/carl9170
carl9170
### update-modules: end processing /etc/modutils/carl9170
### update-modules: start processing /etc/modutils/ipv6
ipv6
### update-modules: end processing /etc/modutils/ipv6
### update-modules: start processing /etc/modutils/r8712u
r8712u
### update-modules: end processing /etc/modutils/r8712u
### update-modules: start processing /etc/modutils/rt2500usb
rt2500usb
### update-modules: end processing /etc/modutils/rt2500usb
### update-modules: start processing /etc/modutils/rt2800usb
rt2800usb
### update-modules: end processing /etc/modutils/rt2800usb
### update-modules: start processing /etc/modutils/rt73usb
rt73usb
### update-modules: end processing /etc/modutils/rt73usb
### update-modules: start processing /etc/modutils/rtl8187
rtl8187
### update-modules: end processing /etc/modutils/rtl8187
### update-modules: start processing /etc/modutils/rtl8192cu
rtl8192cu
### update-modules: end processing /etc/modutils/rtl8192cu
### update-modules: start processing /etc/modutils/usbserial
usbserial
### update-modules: end processing /etc/modutils/usbserial
### update-modules: start processing /etc/modutils/zd1211rw
zd1211rw
### update-modules: end processing /etc/modutils/zd1211rw
 

habe dann update-modules gemacht und die et9200 neu gestartet.

Leider startet Sie nicht.

Edited by dalmidog, 15 December 2011 - 14:34.

[daddelfalk]

Hi,

post complete output from Command "dmesg" just after a fresh reboot.

[dalmidog]

ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42

ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42

Broadcom STB NAND controller (BrcmNand Controller)

bcmemac: Broadcom STB 10/100 EMAC driver v3.0

bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:16:b4:03:f0:fd)

bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)

usbcore: registered new interface driver zd1201

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

brcm-pm: enabling usb clocks

ehci-brcm ehci-brcm.0: Broadcom STB EHCI

ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1

ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300

ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

ehci-brcm ehci-brcm.1: Broadcom STB EHCI

ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2

ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500

ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

ohci-brcm ohci-brcm.0: Broadcom STB OHCI

ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3

ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400

hub 3-0:1.0: USB hub found

hub 3-0:1.0: 2 ports detected

ohci-brcm ohci-brcm.1: Broadcom STB OHCI

ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4

ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600

ata1: SATA link down (SStatus 4 SControl 300)

hub 4-0:1.0: USB hub found

hub 4-0:1.0: 2 ports detected

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

mousedev: PS/2 mouse device common for all mice

i2c /dev entries driver

lirc_dev: IR Remote Control driver registered, major 254

IR NEC protocol handler initialized

IR RC5(x) protocol handler initialized

IR RC6 protocol handler initialized

IR JVC protocol handler initialized

IR Sony protocol handler initialized

IR RC5 (streamzap) protocol handler initialized

IR MCE Keyboard/mouse protocol handler initialized

IR LIRC bridge handler initialized

Bluetooth: Generic Bluetooth USB driver ver 0.6

usbcore: registered new interface driver btusb

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

ALSA device list:

  No soundcards found.

TCP cubic registered

NET: Registered protocol family 17

Bluetooth: HIDP (Human Interface Emulation) ver 1.2

lib80211: common routines for IEEE802.11 drivers

lib80211_crypt: registered algorithm 'NULL'

EBI CS1: setting up NAND flash (primary)

mtd->oobsize=0, mtd->eccOobSize=0

NAND_CS_NAND_XOR=00000000

B4: NandSelect=50000200, nandConfig=16152300, chipSelect=1

brcmnand_read_id: CS1: dev_id=ecda1095

After: NandSelect=50000200, nandConfig=16152300

Block size=00020000, erase shift=17

NAND Config: Reg=16152300, chipSize=256 MB, blockSize=128K, erase_shift=11

busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff

timing1 not adjusted: 5363444f

timing2 not adjusted: 00000fc6

eccLevel=15, 1Ksector=0, oob=16

nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000

<--brcmnand_set_acccontrol: acc b4: d7ff1010, after: d7ff1010

BrcmNAND mfg ec da Samsung K9F2G08U0A 256MB on CS1



Found NAND on CS1: ACC=d7ff1010, cfg=16152300, flashId=ecda1095, tim1=5363444f,											   tim2=00000fc6

BrcmNAND version = 0x0302 256MB @00000000

B4: NandSelect=50000200, nandConfig=16152300, chipSelect=1

brcmnand_read_id: CS1: dev_id=ecda1095

After: NandSelect=50000200, nandConfig=16152300

Found NAND flash on Chip Select 1, chipSize=256MB, usable size=256MB, base=0

brcmnand_scan: B4 nand_select = 50000200

brcmnand_scan: After nand_select = 50000200

page_shift=11, bbt_erase_shift=17, chip_shift=28, phys_erase_shift=17

Brcm NAND controller version = 3.2 NAND flash size 256MB @10000000

ECC layout=brcmnand_oob_bch4_4k

brcmnand_scan:  mtd->oobsize=64

brcmnand_scan: oobavail=50, eccsize=512, writesize=2048

brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3

-->brcmnand_default_bbt

brcmnand_default_bbt: bbt_td = bbt_main_descr

Bad block table Bbt0 found at page 0001ffc0, version 0x01 for chip on CS1

Bad block table 1tbB found at page 0001ff80, version 0x01 for chip on CS1

nand_read_bbt: Bad block at 0x00760000

nand_read_bbt: Bad block at 0x01440000

nand_read_bbt: Bad block at 0x01800000

nand_read_bbt: Bad block at 0x042e0000

nand_read_bbt: Bad block at 0x0bd20000

nand_read_bbt: Bad block at 0x0d1e0000

Adjust partition complete size from entire device to ff00000 to avoid overlap wi											  th BBT reserved space

Adjust partition rootfs size from entire device to f900000 to avoid overlap with											   BBT reserved space

Creating 3 MTD partitions on "brcmnand.0":

0x000000000000-0x00000ff00000 : "complete"

0x000000000000-0x000000600000 : "kernel"

0x000000600000-0x00000ff00000 : "rootfs"

turn off boot console uart0

usb 2-1: new high-speed USB device number 2 using ehci-brcm

turn off boot console early0

UBI: attaching mtd2 to ubi0

UBI: physical eraseblock size:   131072 bytes (128 KiB)

UBI: logical eraseblock size:    126976 bytes

UBI: smallest flash I/O unit:    2048

UBI: VID header offset:		  2048 (aligned 2048)

UBI: data offset:			    4096

hub 2-1:1.0: USB hub found

hub 2-1:1.0: 4 ports detected

ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)

ata2.00: ATA-6: LaCie   HardDrive Quadra, 1AG01118, max UDMA/133

ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)

ata2.00: configured for UDMA/133

scsi 1:0:0:0: Direct-Access	 ATA	  LaCie   HardDriv 1AG0 PQ: 0 ANSI: 5

sd 1:0:0:0: Attached scsi generic sg0 type 0

sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)

sd 1:0:0:0: [sda] Write Protect is off

sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00

sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO											   or FUA

 sda: sda1

sd 1:0:0:0: [sda] Attached SCSI disk

usb 2-1.2: new full-speed USB device number 3 using ehci-brcm

UBI: max. sequence number:	   3517

UBI: attached mtd2 to ubi0

UBI: MTD device name:		    "rootfs"

UBI: MTD device size:		    249 MiB

UBI: number of good PEBs:	    1986

UBI: number of bad PEBs:		 6

UBI: number of corrupted PEBs:   0

UBI: max. allowed volumes:	   128

UBI: wear-leveling threshold:    4096

UBI: number of internal volumes: 1

UBI: number of user volumes:	 1

UBI: available PEBs:			 0

UBI: total number of reserved PEBs: 1986

UBI: number of PEBs reserved for bad PEB handling: 19

UBI: max/mean erase counter: 4/2

UBI: image sequence number:  426623593

UBI: background thread "ubi_bgt0d" started, PID 40

Warning: unable to open an initial console.

UBIFS: recovery needed

UBIFS: recovery completed

UBIFS: mounted UBI device 0, volume 0, name "rootfs"

UBIFS: file system size:   247857152 bytes (242048 KiB, 236 MiB, 1952 LEBs)

UBIFS: journal size:	   9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)

UBIFS: media format:	   w4/r0 (latest is w4/r0)

UBIFS: default compressor: lzo

UBIFS: reserved for root:  0 bytes (0 KiB)

VFS: Mounted root (ubifs filesystem) on device 0:12.

Freeing unused kernel memory: 260k freed

kjournald starting.  Commit interval 5 seconds

EXT3-fs (sda1): warning: maximal mount count reached, running e2fsck is recommen											  ded

EXT3-fs (sda1): using internal journal

EXT3-fs (sda1): recovery complete

EXT3-fs (sda1): mounted filesystem with writeback data mode

usbcore: registered new interface driver tpm

modloader2: module license 'PROPRIETARY' taints kernel.

Disabling lock debugging due to kernel taint

do_cpu invoked from kernel context![#1]:

Cpu 1

$ 0   : 00000000 10008b00 00000000 00000000

$ 4   : e0146000 00000001 e0142ab0 ffffffff

$ 8   : 00000004 00000000 81000218 cfe58000

$12   : 00000001 2ad7d2bb f7537e82 000003ab

$16   : 806f0000 00000001 00000000 806f0000

$20   : e0146000 00000022 00000550 00000124

$24   : 4e0811a1 80013d10

$28   : cf598000 cf599e20 80070fd4 80001450

Hi    : 00000001

Lo    : 328bf3c0

epc   : e0146008 modloader2_init+0x8/0x80 [modloader2]

    Tainted: P

ra    : 80001450 do_one_initcall+0x40/0x1f8

Status: 10008b03    KERNEL EXL IE

Cause : 1080002c

PrId  : 0002a044 (Brcm4380)

Modules linked in: modloader2(P+) tpm

Process modprobe (pid: 87, threadinfo=cf598000, task=cfda0da0, tls=7759b490)

Stack : cf64fe80 00000009 0000000a cf5bc800 e0142af8 e0142ab0 00000001 8005ce38

	    e0142ab0 00000001 80680000 cf64fb00 00000001 00000022 00000550 80072e2c

	    cfda0da0 77584000 cf599f30 80011384 e0142abc 8140fb60 cfda0dd8 e0140024

	    00000006 00000000 00000000 00000000 00000000 e0131000 00009564 e01387bc

	    e013868c e01394fc cfdc1d80 00007e00 00008070 00000000 00000000 00000020

	    ...

Call Trace:

[<e0146008>] modloader2_init+0x8/0x80 [modloader2]

[<80001450>] do_one_initcall+0x40/0x1f8

[<80072e2c>] sys_init_module+0x174/0x1528

[<8000ecfc>] stack_done+0x20/0x40





Code: (Bad address in epc)



---[ end trace 4c58457fcc754913 ]---

usbcore: registered new interface driver ath9k_htc

usbcore: registered new interface driver carl9170

NET: Registered protocol family 10

r8712u: module is from the staging directory, the quality is unknown, you have b											  een warned.

usbcore: registered new interface driver r8712u

usbcore: registered new interface driver rt2500usb

usbcore: registered new interface driver rt2800usb

usbcore: registered new interface driver rt73usb

usbcore: registered new interface driver rtl8187

usbcore: registered new interface driver rtl8192cu

usbcore: registered new interface driver usbserial

USB Serial support registered for generic

usbcore: registered new interface driver usbserial_generic

usbserial: USB Serial Driver core

usbcore: registered new interface driver zd1211rw

Console: switching to colour dummy device 80x25

eth0: no IPv6 routers present

root@et9x00:~#

Edited by dalmidog, 15 December 2011 - 14:45.

[daddelfalk]

Hi,

use attached File replace with yours and do

update-modules -f

Attached Files

•  _et9x00.zip   141bytes   23 downloads

[dalmidog]

Hi,

use attached File replace with yours and do

update-modules -f

Danke, Box startet, es geht wieder

Ich entferne nun das Plugins dvboptions !

[Dimitrij]

Sie können setzen die neue Version.
Es sei denn du hast Angst .
http://openpli.org/f...post__p__238579

Edited by Dima73, 15 December 2011 - 15:23.

[dalmidog]

Tank you very much to all. It's working now!
Regards