I need your help - my Dreambox DM8000HD have been bricked while trying to restore flash from backup.
Output messages from bootloader:
BCM97400
AB
FFFFFFFF
1s
Sync=1
LLMB=1
L2=1
RAC_I=1
RAC_D=1
Copy Code...34TUCV
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM8000
FIRST STAGE 1.10 {BO23456}
2ND STAGE OK, build #83 (2011-03-22)
0.000 - BCM board setup
Configure MEMC1_2........ Done
0.039 - fp init
FP version 7 detected
0.106 - ca init
0.595 - load config
1.175 - config loaded.
* press [S] to enter setup
1.189 - ide init
OLED found!
lcd: BOOT #83
- NAND PROBE: ad da 10 95 (normal)
UNKNOWN FLASH [ad da 10 95]! assuming 64MB!
1.549 - main control
Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000:
USB Hub
- read config file: /boot/secondstage.conf
1.593 - load /boot/secondstage.conf to 833000c0 (max=65535)
found no valid jffs2 block in the first 128k
1.603 - jffs2 size: 0 kb
1.605 - size: -1
- failed to open /boot/secondstage.conf
1.611 - not entering setup
1.613 - execute script: /cf/autorun.bat
1.617 - load /cf/autorun.bat to 833000c0 (max=65535)
1.622 - size: -1
- failed to open /cf/autorun.bat
1.626 - force boot: -1
1.629 - try boot from 1:
1.631 - execute script: /boot/autoexec.bat
1.635 - load /boot/autoexec.bat to 833000c0 (max=65535)
1.640 - size: -1
- failed to open /boot/autoexec.bat
1.645 - try boot from 0:
1.647 - network: 1.649 dhcp
1.701 - starting network
1.707 - httpd, telnetd, dreamupd
dreamupd initialized
1.712 - ok. start receiving packets
USB: New device connected to bus 0 hub 1 port 1
USB: Resetting device on bus 0 port 1
USB: Locating Class 09 Vendor 04CC Product 1520:
USB Hub
USB: New device connected to bus 0 hub 2 port 1
USB: Resetting device on bus 0 port 1
USB: Locating Class 08 Vendor 058F Product 6387:
Mass-Storage Device
USBMASS: Unit 0 connected
Device: USB Disk unit 0
- Sectors: 3893248
- Size: 1901 MiB
P 06 256 3892992 < 3893248
waiting for link...
3.422 - starting dhcp (or manual)
3.425 - network: 3.427 dhcp
3.469 - dhcp started!
waiting for DHCP...
3.542 - got IP address from dhcp
no server address given
using dhcp address
no tftp server address was specified, neither manually nor via dhcp. aborting tftp.
3.597 - try boot from 1:/zImage.elf
lcd: /boot/zImage.elf
3.645 - load /boot/zImage.elf to 82000000 (max=16777216)
3.650 - size: -1
no valid boot source found. press any key to enter setup.
lcd: *** STOP ***
And that's all. Firmware upload through WWW doesn't work (I'm getting connection broken while uploading). What can I do with my Dreambox? Please, help.
Regards.
