Forums

I just tried vix image and reinstall pli4 !! 

everything ok but when reboot I still get the annoying boot logo from vix -- before that I get trend et9000 !

it's not bootlogo.mvi ! did they change it in boot loader? 

I reflash boot loader from ETforums but still there 

plz help me fix this crap 

I have ET9000 and can't get rid of RuDREAM logo either. It's this damn splash screen.

I'm afraid there's nothing you can do for ET9000 at the moment.

Read this: http://openpli.org/f...ange-need-help/ as well as the other threads referenced in there.

wow! who let the dog out !!!! WTF , there must be solution .

I change 5 images nothing happened !

actually I don't trust these guys ! beside I want to put my child picture !

What do you mean you changed 5 images and nothing happened?

Do you mean:

a) you changed 5 images and the VIX logo is still there?

or

B) you changed 5 images and the changes never left an old logo up till now?

If you mean a), it only confirmsa what I wrote above.

I mean IMAGE as a firmware ... Xtrend ,pli,alliance ...etc and I think this logo stuck on bootloader level how they mess with it !?

The vendor logo is not in the image, so flashing an image doesn't help (unless it has specific code to replace it, like VIX).

Xtrend has removed flashing the vendor logo from the bootloader, leaving you with the problem of a third-party logo.

The vendor logo is not in the image, so flashing an image doesn't help (unless it has specific code to replace it, like VIX).

 

Xtrend has removed flashing the vendor logo from the bootloader, leaving you with the problem of a third-party logo.

TY for visiting .

I search the web and find this http://www.world-of-...8984#post258984

but only for VU+ ! don't know what about ET9x00 !

have a look at attached file !

BR

Yes, the VU still supports flashing a vendor logo.

I don't know where it is stored in flash, and how to remove it. You'll need someone (a lot) more technical than I am...

 TY for kindness reply !

and I hope somebody puts light on this

BR

 TY for kindness reply !

and I hope somebody puts light on this

 

 

BR

Did you use the search function here, and on the other forum where you posted the same question?

http://www.et-view-s...ll=1#post143727

The xtrend bootlogo is loaded the same way as an image, but with splash.bin

The vendor logo is not in the image, so flashing an image doesn't help (unless it has specific code to replace it, like VIX).

There is no 'specific code' involved. Just add a splash.bin to the image folder and you're done. Of course the screen must be in the right format.

Cherish it just as bad memory of your adultery

The vendor logo is not in the image, so flashing an image doesn't help (unless it has specific code to replace it, like VIX).

There is no 'specific code' involved. Just add a splash.bin to the image folder and you're done. Of course the screen must be in the right format.

there is no code !

Cherish it just as bad memory of your adultery

 lol ! I attached it to bootloader and splash changed , but problem ! the boot loader takes folder et9000 not et9x00 ! and it's works with pli4 ...

what is the latest bootloader for et9x00 cause I test other bootloader I get BSOD

maybe pli should put generic !

BR

FACT ! pli is best

for the record , http://www.et-view-s...hp?do=file&id=2 solve the problem finally . back to the road.

Best regards

So do I understand you correctly that you had to flash an old bootloader to get rid of this unwanted Splash logo on your ET9x00?

Did you flash the new bootloader again afterwards?

There is no 'specific code' involved. Just add a splash.bin to the image folder and you're done. Of course the screen must be in the right format.

Afaik the current bootloader doesn't have any support anymore for flashing the vendor logo.

Which is why you need the old bootloader to fix it, and which I say that VIX does more than only including the splash.bin, because the current bootloader will not pick it up when you flash anymore.

If that were the case, then including the original xtrend splash.bin when you flash OpenPLi would also fix the problem. Is that the case?

There is no 'specific code' involved. Just add a splash.bin to the image folder and you're done. Of course the screen must be in the right format.

 

Afaik the current bootloader doesn't have any support anymore for flashing the vendor logo.

 

Which is why you need the old bootloader to fix it, and which I say that VIX does more than only including the splash.bin, because the current bootloader will not pick it up when you flash anymore.

 

If that were the case, then including the original xtrend splash.bin when you flash OpenPLi would also fix the problem. Is that the case?

VIX don't anything special ... there no additional code etc.. !

So do I understand you correctly that you had to flash an old bootloader to get rid of this unwanted Splash logo on your ET9x00?

Did you flash the new bootloader again afterwards?

don't attach with bootloader ...

you can do it by attach splash.bin to your IMAGE backup in same folder "et9x00" , cause playing with bootloader is unpredictable case !

good luck

If you unpack the current OpenPLi 4 image on a USB stick, and you add the splash.bin from the old bootloader zip, does it replace it?

If the answer is yes, the story that the current bootloader doesn't support it anymore is false. If the answer is no, VIX does something extra.

That is what I asked. So if I understand you correctly, the answer is yes?

If so, perhaps this should go into the wiki, with instructions and a copy of that splash.bin file, to avoid others from doing what you had to do...

ajeeb, I tried it a few months ago but failed so I assumed that the most recent bootloader does not support splash screen flashing.

If you unpack the current OpenPLi 4 image on a USB stick, and you add the splash.bin from the old bootloader zip, does it replace it?

 

If the answer is yes, the story that the current bootloader doesn't support it anymore is false. If the answer is no, VIX does something extra.

 

That is what I asked. So if I understand you correctly, the answer is yes?

 

If so, perhaps this should go into the wiki, with instructions and a copy of that splash.bin file, to avoid others from doing what you had to do...

splash.bin is a separated file u can make it by yourself ! it's bitmap ... but I use ready file from Xtrend support forum

what I did is attaching the file with old bootloader (not recommended cause my box was BSOD for half day )

you can try now take your backup image and copy splash.bin into et9x00 and try it

I can't test it with firmware now cause am at work

good luck

plz check attached file