Jump to content


Photo

et10000 met realtek RTL8153 gbe driver enigma2

Started by cobus, 12 Dec 2015 15:29

  • Please log in to reply
86 replies to this topic

Re: et10000 met realtek RTL8153 gbe driver enigma2 #21 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+542
Excellent

Posted 13 December 2015 - 13:22

asix dus, wat ik al een paar keer eerder zei ;)

Bus 003 Device 002: ID 0df6:0072 Sitecom Europe B.V. 
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.10
  bDeviceClass          255 Vendor Specific Class
  bDeviceSubClass       255 Vendor Specific Subclass
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x0df6 Sitecom Europe B.V.
  idProduct          0x0072 
  bcdDevice            1.00
  iManufacturer           1 Sitecom Europe BV
  iProduct                2 Sitecom USB 3.0 Gigabit
  iSerial                 3 00000000000001
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           39
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              248mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol      0 
      iInterface              4 Network_Interface
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              11
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x03  EP 3 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
Binary Object Store Descriptor:
  bLength                 5
  bDescriptorType        15
  wTotalLength           22
  bNumDeviceCaps          2
  USB 2.0 Extension Device Capability:
    bLength                 7
    bDescriptorType        16
    bDevCapabilityType      2
    bmAttributes   0x00000002
      Link Power Management (LPM) Supported
  SuperSpeed USB Device Capability:
    bLength                10
    bDescriptorType        16
    bDevCapabilityType      3
    bmAttributes         0x00
    wSpeedsSupported   0x000e
      Device can operate at Full Speed (12Mbps)
      Device can operate at High Speed (480Mbps)
      Device can operate at SuperSpeed (5Gbps)
    bFunctionalitySupport   1
      Lowest fully-functional device speed is Full Speed (12Mbps)
    bU1DevExitLat           1 micro seconds
    bU2DevExitLat         101 micro seconds
Device Status:     0x0000
  (Bus Powered)

static const struct usb_device_id products[] = {
{
    /* ASIX AX88179 10/100/1000 */
    USB_DEVICE(0x0b95, 0x1790),
    .driver_info = (unsigned long)&ax88179_info,
}, {
    /* ASIX AX88178A 10/100/1000 */
    USB_DEVICE(0x0b95, 0x178a),
    .driver_info = (unsigned long)&ax88178a_info,
}, {
    /* D-Link DUB-1312 USB 3.0 to Gigabit Ethernet Adapter */
    USB_DEVICE(0x2001, 0x4a00),
    .driver_info = (unsigned long)&dlink_dub1312_info,
}, {
    /* Sitecom USB 3.0 to Gigabit Adapter */
    USB_DEVICE(0x0df6, 0x0072),
    .driver_info = (unsigned long)&sitecom_info,
}, {
    /* Samsung USB Ethernet Adapter */
    USB_DEVICE(0x04e8, 0xa100),
    .driver_info = (unsigned long)&samsung_info,
}, {
    /* Lenovo OneLinkDock Gigabit LAN */
    USB_DEVICE(0x17ef, 0x304b),
    .driver_info = (unsigned long)&lenovo_info,
},

* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.

Re: et10000 met realtek RTL8153 gbe driver enigma2 #22 cobus

  • Senior Member
  • 4,774 posts

+69
Good

Posted 13 December 2015 - 14:17

Heb deze nu aangeschaft. En dat voor €12.88

 

UT8vaLXXAVaXXagOFbXz.jpg


Groetjes Cobus R

 

VU+ UNO 4K SE FBC DVB-C (8x)

MUTANT HD66SE FBC DVB-C (3x)

MAXYTEC MULTIBOX COMBO

MUTANT HD60 DVB-S

 

 

Ziggo (digitaal) Kabel TV (FTV) op alle decoders met oa fallback tuner

 

Re: et10000 met realtek RTL8153 gbe driver enigma2 #23 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+542
Excellent

Posted 13 December 2015 - 16:59

Dat moet op zich wel gaan lukken, hoewel er een kans is dat de USB id's in de kernel toegevoegd moeten worden, dan de fabrikant even "lief aankijken".


* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.

Re: et10000 met realtek RTL8153 gbe driver enigma2 #24 Sagitarius †

  • Senior Member
  • 4,735 posts

+78
Good

Posted 13 December 2015 - 17:16

Erik Slagter, on 13 Dec 2015 - 16:59, said:

Dat moet op zich wel gaan lukken, hoewel er een kans is dat de USB id's in de kernel toegevoegd moeten worden, dan de fabrikant even "lief aankijken".

Misschien een heel domme vraag maar wat moet je nu met een 3e netwerk aansluiting op de ET10000. :rolleyes: Ik heb een TP Link gigabit switch achter mijn ET8000 liggen, en op 1 poort zit de ET8000, hou ik er nog 6 over van de 8. ;)


73's

PE1AQZ

Re: et10000 met realtek RTL8153 gbe driver enigma2 #25 cobus

  • Senior Member
  • 4,774 posts

+69
Good

Posted 13 December 2015 - 18:09

Dat komt omdat de vlan interface klappert van de et10k

Groetjes Cobus R

 

VU+ UNO 4K SE FBC DVB-C (8x)

MUTANT HD66SE FBC DVB-C (3x)

MAXYTEC MULTIBOX COMBO

MUTANT HD60 DVB-S

 

 

Ziggo (digitaal) Kabel TV (FTV) op alle decoders met oa fallback tuner

 

Re: et10000 met realtek RTL8153 gbe driver enigma2 #26 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+542
Excellent

Posted 14 December 2015 - 18:36

 

Erik Slagter, on 13 Dec 2015 - 16:59, said:

Dat moet op zich wel gaan lukken, hoewel er een kans is dat de USB id's in de kernel toegevoegd moeten worden, dan de fabrikant even "lief aankijken".

Misschien een heel domme vraag maar wat moet je nu met een 3e netwerk aansluiting op de ET10000. :rolleyes: Ik heb een TP Link gigabit switch achter mijn ET8000 liggen, en op 1 poort zit de ET8000, hou ik er nog 6 over van de 8. ;)

Eentje die het wel doet?


* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.

Re: et10000 met realtek RTL8153 gbe driver enigma2 #27 cobus

  • Senior Member
  • 4,774 posts

+69
Good

Posted 31 December 2015 - 07:58

Ik heb hem binnen met de comp moet ik de driver eerst instaleren maar met linux (op de box) doet hij niks nu zitten er deze bestanden bij.kun je daar wat mee ?

Attached Files


Groetjes Cobus R

 

VU+ UNO 4K SE FBC DVB-C (8x)

MUTANT HD66SE FBC DVB-C (3x)

MAXYTEC MULTIBOX COMBO

MUTANT HD60 DVB-S

 

 

Ziggo (digitaal) Kabel TV (FTV) op alle decoders met oa fallback tuner

 

Re: et10000 met realtek RTL8153 gbe driver enigma2 #28 cobus

  • Senior Member
  • 4,774 posts

+69
Good

Posted 31 December 2015 - 14:44

Hierbij de output van lsusb.

root@et10000:~# lsusb
Bus 003 Device 003: ID dead:beef  
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 0b95:1790 ASIX Electronics Corp. 
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@et10000:~#

Dus hij herkent hem wel maar nu dan ?


Groetjes Cobus R

 

VU+ UNO 4K SE FBC DVB-C (8x)

MUTANT HD66SE FBC DVB-C (3x)

MAXYTEC MULTIBOX COMBO

MUTANT HD60 DVB-S

 

 

Ziggo (digitaal) Kabel TV (FTV) op alle decoders met oa fallback tuner

 

Re: et10000 met realtek RTL8153 gbe driver enigma2 #29 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+542
Excellent

Posted 31 December 2015 - 18:41

Toets eens ip link of ip address in?


* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.

Re: et10000 met realtek RTL8153 gbe driver enigma2 #30 cobus

  • Senior Member
  • 4,774 posts

+69
Good

Posted 31 December 2015 - 19:08

Hoe bedoel je in het menu bij netwerk zie ik ook geen 3e netwerk staan en de lampjes branden ook niet als ik de kabel erin doe.

Groetjes Cobus R

 

VU+ UNO 4K SE FBC DVB-C (8x)

MUTANT HD66SE FBC DVB-C (3x)

MAXYTEC MULTIBOX COMBO

MUTANT HD60 DVB-S

 

 

Ziggo (digitaal) Kabel TV (FTV) op alle decoders met oa fallback tuner

 

Re: et10000 met realtek RTL8153 gbe driver enigma2 #31 cobus

  • Senior Member
  • 4,774 posts

+69
Good

Posted 31 December 2015 - 19:30

Dat heb ik ff gedaan maar er staan maar 3 netwerken in een met alles op 00000 en de andere 2 met Mac adres

Groetjes Cobus R

 

VU+ UNO 4K SE FBC DVB-C (8x)

MUTANT HD66SE FBC DVB-C (3x)

MAXYTEC MULTIBOX COMBO

MUTANT HD60 DVB-S

 

 

Ziggo (digitaal) Kabel TV (FTV) op alle decoders met oa fallback tuner

 

Re: et10000 met realtek RTL8153 gbe driver enigma2 #32 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+542
Excellent

Posted 1 January 2016 - 09:42

Derde netwerk interface? Ik ga van 1 naar 2.

 

Als je ip addr doet (of ip link) dan moet je een eth0 en een eth1 zien.

 

Er is een kleine kans dat je een stick met een USB ID die niet herkend wordt als ASIX USB3.0 Gbit adapter, daar is wat aan te doen als we xtrend lief aankijken ;)


* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.

Re: et10000 met realtek RTL8153 gbe driver enigma2 #33 cobus

  • Senior Member
  • 4,774 posts

+69
Good

Posted 1 January 2016 - 17:16

Ik zal veder kijken eerst de verplichtingen afgaan van vandaag.

Groetjes Cobus R

 

VU+ UNO 4K SE FBC DVB-C (8x)

MUTANT HD66SE FBC DVB-C (3x)

MAXYTEC MULTIBOX COMBO

MUTANT HD60 DVB-S

 

 

Ziggo (digitaal) Kabel TV (FTV) op alle decoders met oa fallback tuner

 

Re: et10000 met realtek RTL8153 gbe driver enigma2 #34 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+542
Excellent

Posted 1 January 2016 - 18:10

Wenen of Garmisch Partenkirchen :P ;)


* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.

Re: et10000 met realtek RTL8153 gbe driver enigma2 #35 cobus

  • Senior Member
  • 4,774 posts

+69
Good

Posted 1 January 2016 - 20:58

Haha!!!

Groetjes Cobus R

 

VU+ UNO 4K SE FBC DVB-C (8x)

MUTANT HD66SE FBC DVB-C (3x)

MAXYTEC MULTIBOX COMBO

MUTANT HD60 DVB-S

 

 

Ziggo (digitaal) Kabel TV (FTV) op alle decoders met oa fallback tuner

 

Re: et10000 met realtek RTL8153 gbe driver enigma2 #36 cobus

  • Senior Member
  • 4,774 posts

+69
Good

Posted 1 January 2016 - 22:52

Hierbij de output

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.01.01 22:51:24 =~=~=~=~=~=~=~=~=~=~=~=


openpli 4 et10000




et10000 login: root
root@et10000:~# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000
    link/ether 00:16:b4:07:0a:ff brd ff:ff:ff:ff:ff:ff
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop qlen 1000
    link/ether 00:16:b4:07:0b:ff brd ff:ff:ff:ff:ff:ff
root@et10000:~# ip address
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000
    link/ether 00:16:b4:07:0a:ff brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.13/24 brd 192.168.1.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::216:b4ff:fe07:aff/64 scope link 
       valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop qlen 1000
    link/ether 00:16:b4:07:0b:ff brd ff:ff:ff:ff:ff:ff
root@et10000:~# exit

Groetjes Cobus R

 

VU+ UNO 4K SE FBC DVB-C (8x)

MUTANT HD66SE FBC DVB-C (3x)

MAXYTEC MULTIBOX COMBO

MUTANT HD60 DVB-S

 

 

Ziggo (digitaal) Kabel TV (FTV) op alle decoders met oa fallback tuner

 

Re: et10000 met realtek RTL8153 gbe driver enigma2 #37 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+542
Excellent

Posted 2 January 2016 - 21:42

Ik wilde al roepen, "nou dan werkt het toch", maar een et10000 heeft van zichzelf natuurlijk al twee interfaces.

 

Even het volgende doen:

 

- stick er uit

- dmesg -c

- stick er weer in

- dmesg

 

En wat er uit die laatste dmesg komt even hier posten. Je bent toch wel up to date he?


* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.

Re: et10000 met realtek RTL8153 gbe driver enigma2 #38 cobus

  • Senior Member
  • 4,774 posts

+69
Good

Posted 2 January 2016 - 22:12

Ja ben up-to-date

Groetjes Cobus R

 

VU+ UNO 4K SE FBC DVB-C (8x)

MUTANT HD66SE FBC DVB-C (3x)

MAXYTEC MULTIBOX COMBO

MUTANT HD60 DVB-S

 

 

Ziggo (digitaal) Kabel TV (FTV) op alle decoders met oa fallback tuner

 

Re: et10000 met realtek RTL8153 gbe driver enigma2 #39 cobus

  • Senior Member
  • 4,774 posts

+69
Good

Posted 2 January 2016 - 22:16

Hierbij de complete log.

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.01.02 22:14:17 =~=~=~=~=~=~=~=~=~=~=~=


openpli 4 et10000




et10000 login: root
root@et10000:~# dmesg -c
loop: module loaded
__clk_enable: sata [1]
bcm40nm_pm_sata_enable 00
ahci ahci.0: SSS flag set, parallel bus scan disabled
ahci ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
ahci ahci.0: flags: sntf stag clo slum part 
scsi host0: ahci_platform
scsi host1: ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 42
ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 42
brcmstb_nand: NAND controller driver is loaded
__clk_enable: network [1]
bcm7425_pm_network_enable 00
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
bcmgenet: configuring instance #0 for internal PHY
bcmgenet bcmgenet.0 eth0: link down
__clk_disable: enet [0]
bcm40nm_pm_genet_disable 00
__clk_disable: network [0]
bcm7425_pm_network_disable 00
__clk_enable: network [1]
bcm7425_pm_network_enable 00
__clk_enable: moca_genet [1]
bcm40nm_pm_genet1_enable 00
__clk_enable: moca [1]
bcm40nm_pm_moca_enable 00
Found PHY at Address 31
bcmgenet: configuring instance #1 for external RGMII
__clk_disable: moca [0]
bcm40nm_pm_moca_disable 00
__clk_disable: moca_genet [0]
bcm40nm_pm_genet1_disable 00
__clk_disable: network [0]
bcm7425_pm_network_disable 00
usbcore: registered new interface driver zd1201
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
__clk_enable: usb [1]
bcm40nm_pm_usb_enable 00
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 67, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ehci-brcm ehci-brcm.2: Broadcom STB EHCI
ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3
ehci-brcm ehci-brcm.2: irq 71, io mem 0x10490300
ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
ehci-brcm ehci-brcm.3: Broadcom STB EHCI
ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus number 4
ehci-brcm ehci-brcm.3: irq 72, io mem 0x10490500
ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5
ohci-brcm ohci-brcm.0: irq 68, io mem 0x10480400
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 6
ohci-brcm ohci-brcm.1: irq 69, io mem 0x10480600
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      WDC WD20EARS-00M AB51 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: Attached scsi generic sg0 type 0
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 1 port detected
ohci-brcm ohci-brcm.2: Broadcom STB OHCI
ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7
ohci-brcm ohci-brcm.2: irq 73, io mem 0x10490400
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 1 port detected
ohci-brcm ohci-brcm.3: Broadcom STB OHCI
ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8
ohci-brcm ohci-brcm.3: irq 74, io mem 0x10490600
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
usbcore: registered new interface driver btusb
hidraw: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 17
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: HIDP socket layer initialized
Key type dns_resolver registered
PM: CP0 COUNT/COMPARE frequency does not depend on divisor
EBI CS1: setting up NAND flash (primary)
nand: device found, Manufacturer ID: 0xec, Chip ID: 0xd3
nand: Samsung NAND 1GiB 3,3V 8-bit
nand: 1024MiB, SLC, page size: 2048, OOB size: 64
brcmnand brcmnand.0: 1024MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-16 (1KiB sector)
Bad block table found at page 524224, version 0x01
Bad block table found at page 524160, version 0x01
nand_read_bbt: bad block at 0x000003680000
nand_read_bbt: bad block at 0x00000a520000
nand_read_bbt: bad block at 0x00001c060000
nand_read_bbt: bad block at 0x00003a4e0000
nand_read_bbt: bad block at 0x00003fa60000
Creating 3 MTD partitions on "brcmnand.0":
0x000000000000-0x000040000000 : "complete"
0x000000000000-0x000000600000 : "kernel"
0x000000600000-0x000040000000 : "rootfs"
EBI CS0: setting up SPI flash
brcm_setup_spi_flash: can't locate SPI master
brcm_setup_cs: can't register SPI flash (error -19)
UBI: default fastmap pool size: 256
UBI: default fastmap WL pool size: 25
UBI: attaching mtd2 to ubi0
usb 3-1: new high-speed USB device number 2 using ehci-brcm
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 4 ports detected
ata2: SATA link down (SStatus 0 SControl 300)
UBI: attached by fastmap
UBI: fastmap pool size: 256
UBI: fastmap WL pool size: 25
UBI: attached mtd2 (name "rootfs", size 1018 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 8135, bad PEBs: 9, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 14/7, WL threshold: 4096, image sequence number: 916989219
UBI: available PEBs: 0, total reserved PEBs: 8135, PEBs reserved for bad PEB handling: 151
ALSA device list:
  No soundcards found.
Warning: unable to open an initial console.
UBI: background thread "ubi_bgt0d" started, PID 57
 sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
UBIFS: background thread "ubifs_bgt0_0" started, PID 58
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 1011617792 bytes (964 MiB, 7967 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
UBIFS: reserved for root: 0 bytes (0 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID C5248606-9582-42A6-8C35-DC9C1055266D, small LPT model
VFS: Mounted root (ubifs filesystem) on device 0:11.
devtmpfs: mounted
Freeing unused kernel memory: 228K (80867000 - 808a0000)
usb 3-1.1: new full-speed USB device number 3 using ehci-brcm
random: nonblocking pool is initialized
EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
usbcore: registered new interface driver tpm
dvb: module_layout: kernel tainted.
Disabling lock debugging due to kernel taint
i2c-core: driver [tmp101] using legacy suspend method
i2c-core: driver [tmp101] using legacy resume method
i2c i2c-3: This adapter will soon drop class based instantiation of devices. Please make sure client 0x48 gets instantiated by other means. Check 'Documentation/i2c/instantiating-devices' for details.
i2c-core: driver [stv6418] using legacy suspend method
i2c-core: driver [stv6418] using legacy resume method
i2c i2c-2: This adapter will soon drop class based instantiation of devices. Please make sure client 0x4b gets instantiated by other means. Check 'Documentation/i2c/instantiating-devices' for details.
Console: switching to colour frame buffer device 160x45
input: dreambox remote control (native) as /devices/virtual/input/input0
input: dreambox advanced remote control (native) as /devices/virtual/input/input1
DVB: registering new adapter (dvb0)
i2c i2c-2: This adapter will soon drop class based instantiation of devices. Please make sure client 0x08 gets instantiated by other means. Check 'Documentation/i2c/instantiating-devices' for details.
i2c i2c-3: This adapter will soon drop class based instantiation of devices. Please make sure client 0x08 gets instantiated by other means. Check 'Documentation/i2c/instantiating-devices' for details.
i2c i2c-4: This adapter will soon drop class based instantiation of devices. Please make sure client 0x08 gets instantiated by other means. Check 'Documentation/i2c/instantiating-devices' for details.
platform dvb0.0: DVB: registering adapter 0 frontend 0 (DVB-S2)...
platform dvb0.0: DVB: registering adapter 0 frontend 1 (DVB-S2)...
platform dvb0.0: DVB: registering adapter 0 frontend 2 (DVB-S2)...
input: front panel as /devices/virtual/input/input2
Console: switching to colour dummy device 80x25
__clk_enable: network [1]
bcm7425_pm_network_enable 00
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
bcmgenet bcmgenet.0 eth0: link up, 100 Mbps, full duplex
NET: Registered protocol family 10
dvb_demux_feed_del: feed not in list (type=0 state=0 pid=ffff)
dvb_demux_feed_del: feed not in list (type=0 state=0 pid=ffff)
dvb_demux_feed_del: feed not in list (type=0 state=0 pid=ffff)
echo (23629): drop_caches: 1
dvb_demux_feed_del: feed not in list (type=0 state=0 pid=ffff)
usb 4-1: new high-speed USB device number 2 using ehci-brcm
usb 4-1: USB disconnect, device number 2
root@et10000:~# dmesg
usb 4-1: new high-speed USB device number 3 using ehci-brcm
root@et10000:~# exit

Groetjes Cobus R

 

VU+ UNO 4K SE FBC DVB-C (8x)

MUTANT HD66SE FBC DVB-C (3x)

MAXYTEC MULTIBOX COMBO

MUTANT HD60 DVB-S

 

 

Ziggo (digitaal) Kabel TV (FTV) op alle decoders met oa fallback tuner

 

Re: et10000 met realtek RTL8153 gbe driver enigma2 #40 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+542
Excellent

Posted 3 January 2016 - 13:52

En nu nog even doen wat ik had gevraagd ;)


* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.

Back to [NL] Gebruikersondersteuning

10 user(s) are reading this topic

0 members, 10 guests, 0 anonymous users

  1. Forums
  2. → PLi® Support
  3. → [NL] Gebruikersondersteuning