Posted 8 July 2017 - 12:48
I've already dealt with myself. Just in skin.xml have to line up <! - Volume -> <screen name = "Volume" title = "Volume" position = "0.360" on
<! - Volume -> <screen name = "Volume" title = "Volume" position = "20,360" Thank you for your help. Please to fix yet another HbbTV to work properly.
Edited by ciciol, 8 July 2017 - 12:48.
Posted 8 July 2017 - 12:51
OK, before I install v6 can I ask if anything that is included with v4 is missing from v6?
I suppose I am asking if it is fully functional like v4?
Posted 8 July 2017 - 14:50
OK, before I install v6 can I ask if anything that is included with v4 is missing from v6?
I suppose I am asking if it is fully functional like v4?
Yes, it runs (basically) the same enigma.
It could however be that external and/or binary stuff no longer works, for example if they have a depedency on a very old library, or an old gstreamer version (like some HbbTV binaries).
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 8 July 2017 - 15:26
Posted 8 July 2017 - 15:36
Do you mind that I have absolutely NO clue what you are on about?
What is "your box"? And what is your issue with it? Obviously, the purpose of this RC is to fix problems you encounter in the wild that we haven't seen while testing.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 8 July 2017 - 17:23
Edited by daveraver, 8 July 2017 - 17:24.
Posted 8 July 2017 - 17:34
Perhaps the wiki needs a section on skin design, to explain how you can make these modifications yourself.
Edited by 40H3X, 8 July 2017 - 17:35.
Hardware: Vu+ Uno 4K SE - Vu+ Duo 4K - Fuba 78 cm - Tripleblock LNB Quad 19.2/23.5/28.2 - DS918+
Software : OpenPLi - OSCam - Settings van Hans - Autotimer - EPGImport
---------------------------------------------------------------------------------------------------------------------------------------
Remember: Upvote with the 
button for any user/post you find to be helpful, informative, or deserving of recognition!
---------------------------------------------------------------------------------------------------------------------------------------
Many answers to your question can be found in our new and improved wiki
Posted 8 July 2017 - 17:55
I've edited the plugin.py file inside transcode setup plugin folder, this way it works, but you have to generate the file manually, not through openwebif... adding ?bitrate=1000000 that is the maximum bitrate of formuler1 transcode. I hope this feature will be fixed if possible. thank you.I install transcode setup, it appears on webif, but dont take the values I put... I have changed the drivers to February 12 2017, this way it worked with openpli4. I will take a look on threads I wrote some months ago. If you can make a review, or wait some days I look for the solution, I achieved with openpli4, now RC6 dont take the transcode values as openpli4 did. thank you.
Posted 8 July 2017 - 18:40
Ah, ok, You have a formuler 1. For which there are only experimental drivers that enable transcoding, which are not published by the manufacturer in the BSP. So as far as OpenPLi is concerned, the box doesn't support transcoding.
We can check again with the manufacturer what the status is. If it will be enabled, it requires autoinstall of the plugin, and code changes to the streamproxy (hardwar detection) and the webif.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 8 July 2017 - 20:07
Edited by daveraver, 8 July 2017 - 20:08.
Posted 8 July 2017 - 20:14
Posted 8 July 2017 - 21:20
Edited by betacentauri, 8 July 2017 - 21:21.
Posted 8 July 2017 - 22:06
Not sure what you mean by 1. But every channel is numbered, always. Maybe whether or not to display it depends on the skin?
As for 2: no, not a problem, and is used here daily. Are you sure it is imported properly? Config ok (UK source was recently renamed)? Is the time on the box ok?
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 9 July 2017 - 04:41
Possible to make this image for Gigablue UHD Quad 4K?
VU+ Ultimo 4K, 19.2, 13, 4.8 E via switch on input/tuner 1. 1W. Inverto Unicable II LNB IDLU-32UL40 on input/tuner 2. OpenPLi 8.3
Posted 9 July 2017 - 07:06
Posted 9 July 2017 - 09:20
help hoe kan flash xtrend et7500?
Posted 9 July 2017 - 09:22
Mutant HD2400, OpenPLi nightly, 2x DVB-C & 2x DVB-S
Mutant HD51, OpenPLi nightly, 1x DVB-C & 1x DVB-S
Wavefrontier T55 (Astra 1,2,3 en HB)
Smartcards Ziggo (Irdeto) and CDS (Seca) on Oscam
Posted 9 July 2017 - 09:28
OK, before I install v6 can I ask if anything that is included with v4 is missing from v6?
I suppose I am asking if it is fully functional like v4?
It is a "release candidate". So you do the maths yourself 
* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.
Posted 9 July 2017 - 11:49
Posted 9 July 2017 - 12:36
On 1.... Ok on 4.0 openpli its possible not show number in channels
On 2 .. yep i config like on 4.0...import success with 63.356 entries but these are not show on channels ?!
1. Then it is not possible. Enigma in 4 and 6 is virtually the same.
2. Have you checked if the date on your box is correct?
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
0 members, 3 guests, 0 anonymous users
This topic is locked
