Posted 17 May 2018 - 17:29
Hi Guys
I have a VU+Duo2 that's been Crashing (Green Screen) since updating to Openpli 6.2. The crash happens when using the XtremeTv Streaming plugin. This has never been a problem before on either Openpli 4.0, 6.0 0r 6.1. I've attached a recent Crashlog, in the hope that someone may see the cause. I've re-installed my previous backup (Openpli 6.1) & all is working fine.
Regards
Wizard
enigma2_crash_1526571429.log 15.26KB
19 downloads
Posted 17 May 2018 - 18:21
Difficult to say as there are a lot of issues with that plugin before enigma eventually crashes.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 17 May 2018 - 18:42
Posted 17 May 2018 - 18:49
Ok thank you. I think I will have to stick with Openpli 6.1 for now.
Regards
Wizard
Posted 17 May 2018 - 18:55
Posted 17 May 2018 - 19:02
If updating is the problem, try to flash a fresh OpenPLi 6.2 image to start on a STB with a clean installation and not an updated version.
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Posted 17 May 2018 - 19:25
Posted 17 May 2018 - 19:29
Posted 17 May 2018 - 19:33
Hi Domi76
Did you also try athoik suggestion ? ( Can you enable fallback tuner (use dummy ip) and test if it crashes with fallback tuner enabled? )
Regards
Posted 17 May 2018 - 20:05
Posted 17 May 2018 - 20:37
Hi,
Go in the setup screen where you can enable the remote fallback tuner.
There a new entry field will appears and there type in a fake IP address: 10.0.0.1 for exemple.
Then test to see if you receiver will still crash or not.
Pr2
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Posted 17 May 2018 - 20:38
Hi
As luck would have it, I made a complete backup of 6.2 before re-flashing back to 6.1. Tomorrow I will reinstate 6.2 & try what athoik suggests. I'm not entirely sure, but do remember seeing fallback tuner option in there. I'll post back here Once tested.
Regards
Wizard
Posted 18 May 2018 - 10:39
Hi Guys
I've now re-installed Openpli 6.2 & followed the above instructions. In service searching there is an option called Fallback Remote Receiver Setup. I've enabled it & added a dummy Ip (10.0.0.1) then saved. I've then rebooted the receiver.
Unfortunately this has not fixed the problem. Its the same as before. I can run XtreamTv, but as soon as I start to change channels it crashes. I've attached another Crashlog from this morning. I've had to re-instate 6.1 for now.
Regards
Wizard 
enigma2_crash_1526635045.log 12.68KB
2 downloads
Posted 18 May 2018 - 10:50
PC: 7733cdd8 00000000 00000001 71e4a884 77333af8 773e12c0 00000000 35e298ce 773d98e8 773d98e8 752e6769 00000000 666e6f63 0000003b 6c6c6166 6b636162 616e655f 71e4a888 769291b8 00000000 00000000 00000000 00000000 71e4a880 7694f3f0 00000017 772d6000 00000000 00000000 773fafb0 68bfe8b0 00000001 7733b770 Backtrace: /usr/bin/enigma2(_Z17handleFatalSignaliP9siginfo_tPv) [0x462D4C] /usr/lib/libpython2.7.so.1.0(PyEval_EvalFrameEx) [0x7733CDDA] -------FATAL SIGNAL
WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W
Posted 18 May 2018 - 10:52
But as it seems to be related to illegal IPTV streaming....it is extreme difficult to troubleshoot....
But it still could be related to the newer gstreamer/streampoxie/servicemp3 version we have in the image now in combination with 'wierdness' in those 'dark-web' streams...
Edited by littlesat, 18 May 2018 - 10:55.
WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W
Posted 18 May 2018 - 11:40
Posted 18 May 2018 - 12:05
Hi
I also own an Xtrend 8500, I've just updated that to Openpli 6.2 & installed XtremeTv. That works perfectly, no crashing at all so far. There must be some kind of conflict with files or drivers within the VU+Duo2 after updating that to 6.2.
Regards
Wizard
Posted 18 May 2018 - 12:28
Now it sounds the new VU drivers are the cullpit...
WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W
Posted 18 May 2018 - 12:31
Hi littlesat
Can you make Vu aware of this problem ?
Regards
Wizard
Posted 18 May 2018 - 13:05
You can try to put the old drivers back and confirm... (they did not increase kernel version so that should be possible)
WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W
0 members, 3 guests, 0 anonymous users
