Hi I recently install Openpli 7.3-relase on my Dreambox 8000 (oryg) but iam having problem with satellites . Tuner A configured on 13.0 Hotbird and Tuner B Diseq 13.0 hotbird / 28.2 Astra . seemes like hotbird channels are not available at all all chanells are not highlighted there no FTA channels as well . Keep seing check tuner configuration .Sygnal strengt is showing at 80 % so as always . Did anyone has similar issues or any clues much apriciated ...
open pli 7.3 satelitte problem
Started by 00aiix00, 23 Aug 2020 16:02
12 replies to this topic
Re: open pli 7.3 satelitte problem #2
-
- Senior Member
- 39 posts
0
Neutral
Posted 27 August 2020 - 05:50
I have same problem with my gigablue ue4k, i must install older one
Re: open pli 7.3 satelitte problem #3
-
- PLi® Core member
- 71,173 posts
+1,842
Excellent
Posted 27 August 2020 - 11:04
No, don't have this issue. I've got 3 tuners with 19.2 / 23.5 / 28.2 on DiseqC and a 4th with only 28.2 (no DiseqC), and they all work fine.
Please post screenshots of your tuner configuration ( use the web interface, make sure to check the high resolution box, and the "more reply options" button below to attach the screenshots ).
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: open pli 7.3 satelitte problem #4
-
- Senior Member
- 39 posts
0
Neutral
Posted 2 September 2020 - 07:51
I have a problem with it from april 2020, when i use openpli, openatv, openhdf,... It is same problem. I use multiswitch, and when i try it in other output - same result. My option is: mode diseqc a, b, c, d
Re: open pli 7.3 satelitte problem #5
-
- PLi® Core member
- 71,173 posts
+1,842
Excellent
Posted 2 September 2020 - 12:19
This is the tuner config of my first three inputs:
1_0_19_1B1D_802_2_11A0000_0_0_0_20200902121729.jpg 99.25KB
5 downloads
And my fourth input:
1_0_19_1B1D_802_2_11A0000_0_0_0_20200902121751.jpg 105.47KB
4 downloads
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: open pli 7.3 satelitte problem #6
-
- Senior Member
- 39 posts
0
Neutral
Posted 3 September 2020 - 07:57
i will a take a photo when i will at home. interestingly, it only makes a mistake with one satellite (23.5e) and writes a signal error. I can swap it to any input - there is not always a signal on this satellite. Signal on this satellite is about 12-13dB
Edited by tomko, 3 September 2020 - 07:58.
Re: open pli 7.3 satelitte problem #7
-
- Senior Member
- 39 posts
0
Neutral
Posted 7 September 2020 - 15:49
i will a take a photo when i will at home. interestingly, it only makes a mistake with one satellite (23.5e) and writes a signal error. I can swap it to any input - there is not always a signal on this satellite. Signal on this satellite is about 12-13dB
this is my pictures before and after update
1. picture signall before update
2. picture option before update
3. picture signal after update
4. picture option after update
Attached Files
-
pred_signal.jpg 72.13KB
2 downloads
-
nastavenie.jpg 106.42KB
2 downloads
-
po_novy.jpg 73.86KB
2 downloads
-
nastavenie _po.jpg 79.86KB
2 downloads
Re: open pli 7.3 satelitte problem #8
-
- PLi® Core member
- 71,173 posts
+1,842
Excellent
Posted 7 September 2020 - 16:42
And you haven't changed the satellites.xml, installed a new one, or replaced a channel list containing either this file or a lamedb file at the same time?
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: open pli 7.3 satelitte problem #9
-
- Senior Member
- 39 posts
0
Neutral
Posted 7 September 2020 - 18:26
IT is same lamedb, i do it today with same lamedb. I first i try setting from openpli when i installed new one - no signal, then i try send my setting-no signal. This problem is from april 2020.i do not know what is changed
Re: open pli 7.3 satelitte problem #10
-
- PLi® Core member
- 71,173 posts
+1,842
Excellent
Posted 7 September 2020 - 21:30
Nothing has changed, and I can't reproduce this behaviour on any of my boxes.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: open pli 7.3 satelitte problem #11
-
- Senior Member
- 39 posts
0
Neutral
Posted 14 September 2020 - 14:35
I was expecting such an unspeakable answer
Re: open pli 7.3 satelitte problem #12
-
- Senior Member
- 615 posts
+3
Neutral
Re: open pli 7.3 satelitte problem #13
-
- Senior Member
- 39 posts
0
Neutral
Posted 16 September 2020 - 15:08
Riki, thanx for info
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users
