#1
Posted 12 January 2009 - 19:36
I use the latest pli img and a boot takes 2-5min is this normal? sometimes it gets stuck in the boot menu,have to pull the plugg to reboot.
Many times on a boot it says setting up for first time use on the pli picture on the boot screen,but its not the first time.
After a web software update i get a question on rebooting after the update,i choose yes and the pli bootmenu gets on my screen and the box is not rebooting and has no power.
I have to pull the plugg to get it on again,and sometimes i have to put the plug in and out 4-8 times before i get power on the box and its starting.
Sometimes when scanning for channels it crashes and gets stuck,allsow have to pull the plugg nothing working anymore.
I can live with problems since its all just small 1s,but maybe some1 can make a link between thoose problems and my satfinder problem......
PS:i have reflashed,and its a orginal dm 800 hd.....
Re: Dm 800 bugs? #2
Posted 12 January 2009 - 21:07
Re: Dm 800 bugs? #3
Re: Dm 800 bugs? #4
Posted 13 January 2009 - 00:38
In my humble opinion, PLi Jade is a no go on the DM800 until these problems are resolved.
Cheers
I have a list with small problems i have on my dm 800.
I use the latest pli img and a boot takes 2-5min is this normal? sometimes it gets stuck in the boot menu, have to pull the plug to reboot.
After a web software update i get a question on rebooting after the update,i choose yes and the pli bootmenu gets on my screen and the box is not rebooting and has no power.
I have to pull the plugg to get it on again,and sometimes i have to put the plug in and out 4-8 times before i get power on the box and its starting.
Sometimes when scanning for channels it crashes and gets stuck,allsow have to pull the plugg nothing working anymore.
Re: Dm 800 bugs? #5
Posted 13 January 2009 - 00:52
Hi there, I'm having exactly the same problems. On a second DM800 I cannot even get my first satellite installed as it keeps freezing on the tuner configuration page - usually when I'm trying to select my satellite (Intelsat 8 at 166, which requires quite a few buttons presses). It is even worse if I try and hold the right arrow key to scroll quickly through the list of satellites - I can usually only get to 64 degrees east !
Yet I have never had these problems at all with tuning satellites. I use a 8x8 multiswitch here as shown in the wiki >> E2Tuner << , being a mixture of Ku single, Ku universial and C band LNB's. Here is IS8 C Band settings I use and it is perfect
Re: Dm 800 bugs? #6
Posted 13 January 2009 - 01:16
half the problem is the dreambox 800 needs to be unpluged for at least 30sec before you plug it in else it gets stuck on bootup. the other half seems to be a timing issue with some kernel modules, there is a thread on this subject here, search and you'll find the resolve.
I think you hit the nail on the head here in part two of your answer. I personally think it is LAN related, as this morning I put my 800 on a non LAN set up on a local HDTV channel (I have no LAN connected - wired nor wifi) and the boot times almost triple (same issues with some E1 boxes) because;
1. No LAN detected
2. Devices that the 800 think are attached via the LAN are not attached and need to timeout before the next part of boot takes place
So this would mean these issues could be part of the other users issues relating to boot up of the 800
1. misconfigured LAN in the DM800
2. misconfigured LAN settings for attached devices
3. attached LAN devices not attached or turned on (mount/movire plugin etc)
4. LAN not available at DM800's boot time for whatever reason (no DHCP server, DHCP server busy and a pile of other normal issues)
5. LAN not available when an external device is called (a pile of reasons why, see above note) during boot up / start up
etc etc
Just my two pence worth ...
Re: Dm 800 bugs? #7
Posted 13 January 2009 - 01:54
I think you hit the nail on the head here in part two of your answer. I personally think it is LAN related, as this morning I put my 800 on a non LAN set up on a local HDTV channel (I have no LAN connected - wired nor wifi) and the boot times almost triple (same issues with some E1 boxes) because...
Are you using the latest Jade2 firmware and the latest enigma2 ? That's what I have installed (not for much longer though)
Yet I have never had these problems at all with tuning satellites. I use a 8x8 multiswitch here as shown in the wiki >> E2Tuner << , being a mixture of Ku single, Ku universial and C band LNB's. Here is IS8 C Band settings I use and it is perfect
Re: Dm 800 bugs? #8
Posted 13 January 2009 - 02:31
However in this latest release apart from the satellites.xml being split back to front from the earlier Jade E2 release (where the Ku postion has been swapped with the C band position on satellites that have both the C/Ku bands - this only effects the picons) I could not find anything wrong, and still can not. A good way to see this is to check the E2 wiki pages, which I write off the DM800 here.
However I did see major delays in boot/start up times when I had mounts/mediaplayers and other LAN dependant actions on a non LAN environment like I have the 800 on now.
PS: Off IS2 169e C band last night - on the Globecast feed channel - Setanta Sport Australia running FTA
Re: Dm 800 bugs? #9
Re: Dm 800 bugs? #10
Posted 13 January 2009 - 04:00
Having said this it takes an age if you have moved the dish off the default start channels satellite (as I did with the Motek to test it), but still works never the less
Re: Dm 800 bugs? #11
Posted 13 January 2009 - 05:55
IMHO, it should work OK as all you have enabled is diseqc 1.2 and the appropriate diseqc's AA or AB etc for the LNB's, but I never tested it 100% on this. I chucked my motek on it and it worked, but I will put a vbox on the 3.2m and try it later and see if this is an issue, but the motek should have found any issue with the diseqc 1.2 settings.
Having said this it takes an age if you have moved the dish off the default start channels satellite (as I did with the Motek to test it), but still works never the less
I confirm this works 100% even better than the Dm500, 600 and 7020 I have here (suprised me just how well it works) and so fast to, compared to these other boxes. So I think it is simply a set up issue there you have for diseqc 1.2 What the issue you have is, I do not know sorry.
I will get around to writing the wiki for motek and vbox type movers in due course.
Re: Dm 800 bugs? #12
Re: Dm 800 bugs? #13
Re: Dm 800 bugs? #14
Posted 13 January 2009 - 20:42
Sorry do not agree with this at all. Maybe you have some issues to overcome (said as a true ANZAC = me being a Kiwi and all - tongue in cheek)
I'm not imagining things, I battled around for 2 days trying to get 2 different DM800's to work and no luck. You need to read the comments of many others and your own administrators as well, so don't bury your head in the sand (said in the true spirit of an ANZAC)
Re: Dm 800 bugs? #15
Posted 13 January 2009 - 22:45
The cause for not loading, is most likely to be the hardware. If the component isn't ready, the drivers can't get loaded i guess.
It's just a modprobe with no "load verification".
Re: Dm 800 bugs? #16
Re: Dm 800 bugs? #17
Re: Dm 800 bugs? #18
Re: Dm 800 bugs? #19
Re: Dm 800 bugs? #20
Also tagged with one or more of these keywords: DM800
dm800hd-pvrStarted by mimisiku, 12 Feb 2020 Dm800, openpli 2.1 |
|
|||
DM800HD Tuner A emptyStarted by Popol95, 17 Dec 2016 Tuner, DM800, Openpli4, openpli |
|
|||
Error in Remote Stream ConverterStarted by DutchZombie, 31 Oct 2016 Vu+, DM800 |
|
|||
Zenders werken niet meerStarted by Ranger61, 5 Feb 2016 dm800, Zenders, Dreambox |
|
|||
OSCam 1.20 op oeroude DM800 i.c.m. OpenPli 2.1Started by goldeneye , 25 Sep 2015 Dm800, OpenPli 2.1 |
|
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users