Why would you install vpnmanager if you say: "It works fine if enigma2-plugin-extensions-vpnmanager_1.1.7-py3 is not installed."
Then you won't need it apparently.
OpenPLi-py3
Started by darog69, 16 Jan 2022 21:00
1139 replies to this topic
Re: OpenPLi-py3 #601
-
- Senior Member
- 3,480 posts
+43
Good
Posted 19 September 2022 - 18:51
2 x ultimo4k (dvb-c fbc + 1 dvb-s2, 9.0r/nb) + een et10k/osmini ((nb) geen tuners en dus fallbackclient, nb) met een Synology ds214+ (2 x 6 TB) op DSM 7.1.1 in ziggo oost (voormalig @Home) + A1/A2/A3/HB (TechniSat)
Re: OpenPLi-py3 #602
-
- Senior Member
- 319 posts
+4
Neutral
Posted 19 September 2022 - 18:57
Because i do also an openpli update. 
Re: OpenPLi-py3 #603
-
- Senior Member
- 319 posts
+4
Neutral
Posted 19 September 2022 - 19:07
I put the plugin again, same problem.
I restore the settings, (no reboot), the Wlan works fine.
After that with the plugin openvn start and stop correctly.
Something is not in the good order.
Re: OpenPLi-py3 #604
-
- PLi® Core member
- 70,219 posts
+1,798
Excellent
Posted 19 September 2022 - 19:15
DNS for static IP is impossible set ... resp. can be set, but after 'ok' are again both on 0.0.0.0
That should have been fixed, my new code writes static DNS entries in /etc/network/interfaces, instead of /etc/resolv.conf (which is volatile, and caused the problem).
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: OpenPLi-py3 #605
-
- Senior Member
- 3,480 posts
+43
Good
Posted 19 September 2022 - 21:35
My et10k (fallback client only, no tuners available) is also running the py3 nb now with no problems,
2 x ultimo4k (dvb-c fbc + 1 dvb-s2, 9.0r/nb) + een et10k/osmini ((nb) geen tuners en dus fallbackclient, nb) met een Synology ds214+ (2 x 6 TB) op DSM 7.1.1 in ziggo oost (voormalig @Home) + A1/A2/A3/HB (TechniSat)
Re: OpenPLi-py3 #606
-
- PLi® Core member
- 13,764 posts
+214
Excellent
Posted 19 September 2022 - 22:33
DNS for static IP is impossible set ... resp. can be set, but after 'ok' are again both on 0.0.0.0
That should have been fixed, my new code writes static DNS entries in /etc/network/interfaces, instead of /etc/resolv.conf (which is volatile, and caused the problem).
As I saw, now it is saved to /etc/network/interfaces and to /etc/resolv.conf too. But I have problem, when I go to set DNS, DNS are 0.0.0.0... py3 ?
Weird for me - try go to Networks - Adapter settings - you will see existing working dns . Press blue => both dns are then 0.0.0.0 (=> existing dns cannot be edited) - Exist ... both dns are 0.0.0.0. Exit and go again to Adapter setting - still existing dns...
Edited by ims, 19 September 2022 - 23:15.
Kdo nic nedělá, nic nezkazí!
Re: OpenPLi-py3 #607
-
- PLi® Core member
- 70,219 posts
+1,798
Excellent
Posted 20 September 2022 - 14:50
Yes.
Only static DNS entries can be edited and saved. So if your DNS has been assigned via DHCP, both entries are still 0.0.0.0, as you don't have any static DNS entries defined.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: OpenPLi-py3 #608
-
- PLi® Core member
- 13,764 posts
+214
Excellent
Posted 20 September 2022 - 15:03
Yes.
Only static DNS entries can be edited and saved. So if your DNS has been assigned via DHCP, both entries are still 0.0.0.0, as you don't have any static DNS entries defined.
I am writing about static DNS ...
Kdo nic nedělá, nic nezkazí!
Re: OpenPLi-py3 #609
-
- PLi® Core member
- 70,219 posts
+1,798
Excellent
Posted 20 September 2022 - 15:09
Hmm... That is not ok.
You do have your static DNS defined in /etc/network/interfaces?
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: OpenPLi-py3 #610
-
- PLi® Core member
- 70,219 posts
+1,798
Excellent
Posted 20 September 2022 - 15:28
Just did a test here:
Starting position: LAN connection, DHCP, DNS supplied by DHCP.
==> In the network settings, DNS1 = IP from DHCP, DNS2 = 0.0.0.0, under nameservers, both are 0.0.0.0 (no static DNS assigned)
Entered 8.8.8.8 as first static DNS, left the second empty
==> In the network settings, DNS1 = 8.8.8.8, DNS2 = IP from DHCP (as static goes before dynamic).
So this is correct.
After a reboot, DNS is still as it should be, but for some reason both LAN and WLAN are not active, and I can't seem to activate them again, so I need to look at what goes wrong there.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: OpenPLi-py3 #611
-
- PLi® Core member
- 70,219 posts
+1,798
Excellent
Posted 20 September 2022 - 15:39
Hmm, more buggy code.
In /etc/network/interfaces, "dns-nameserver" should be defined per iface stanza, so every interface has (can have) its own DNS definition. But in Components/Network, DNS is considered global.
More work needed, I'll ry to find the time asap.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: OpenPLi-py3 #612
-
- PLi® Contributor
- 720 posts
+46
Good
Posted 21 September 2022 - 20:03
I just flashed NB. The infobarweather plugin seems to be missing from the feed...
Sorry to inform you this member, my brother, passed away.
Re: OpenPLi-py3 #613
-
- PLi® Contributor
- 720 posts
+46
Good
Posted 21 September 2022 - 21:37
I just flashed NB. The infobarweather plugin seems to be missing from the feed...
Please ignore that. Autorestore restored it from the feed, so it was not on the installable plugin list anymore... 
Sorry to inform you this member, my brother, passed away.
Re: OpenPLi-py3 #614
-
- Senior Member
- 104 posts
+2
Neutral
Posted 23 September 2022 - 09:41
Tested todays develop for Zgemma H9 combo, found no problems for normal daily use in my setup
Re: OpenPLi-py3 #615
-
- Member
- 11 posts
0
Neutral
Posted 24 September 2022 - 19:01
The receiver 4K BOX HD60 (mutant ax60) does not work the recovery (openpli-develop-hd60-20220923_recovery_emmc) !
Re: OpenPLi-py3 #616
-
- Member
- 11 posts
0
Neutral
Posted 24 September 2022 - 19:03
Does not read the flash usb well !
Writes that there are no files.
Re: OpenPLi-py3 #617
-
- PLi® Contributor
- 1,857 posts
+87
Good
Posted 25 September 2022 - 21:50
The receiver 4K BOX HD60 (mutant ax60) does not work the recovery (openpli-develop-hd60-20220923_recovery_emmc) !
This is still a test build environment.
Why does it have to be a recovery image from the python 3 branch?
If you test, you should also be able to provide logs, otherwise nobody can help.
A receiver does not always need a recovery image, but actually only very rarely.
The images are loaded normally into the flash.
The error just seems to be an unreadable USB stick.
Re: OpenPLi-py3 #618
-
- PLi® Contributor
- 1,602 posts
+203
Excellent
Posted 26 September 2022 - 05:31
Does not read the flash usb well !
Writes that there are no files.
Try another USB-stick.
I have same problem with Gigablue trio4K, some doesn't work, while there's nothing wrong with
Edited by Beeker, 26 September 2022 - 05:31.
Dreambox dm920, Uclan Ustym4Kpro, Gigablue UHD TRIO 4K and Dreambox dm8000. Wavefrontier T55 13.0|19.2|23.5|28.2 + Ziggo.
Re: OpenPLi-py3 #619
-
- Senior Member
- 1,634 posts
+14
Neutral
Posted 27 September 2022 - 06:44
Hello,
Since last week I've been testing the nightly and found 2 issues yesterday:
1. If you go to the openwebif and select autotimer list on the left bottom the list remains empty (see screenshot, while in the enigma gui you can see the entries). If I go to 8.3 the entries are visible so it would seem to be a py3 thingy
2. The RSS reader does show sources (like TotaalTV), but when you select one there are no entries visible in nightly (while there are on 8.3, see enclosed screenshot)
Attached Files
-
8.3.jpg 104.89KB
4 downloads
-
Schermafbeelding 2022-09-27 074045.JPG 59.64KB
4 downloads
Mutant HD2400, OpenPLi nightly, 2x DVB-C & 2x DVB-S
Mutant HD51, OpenPLi nightly, 1x DVB-C & 1x DVB-S
Wavefrontier T55 (Astra 1,2,3 en HB)
Smartcards Ziggo (Irdeto) and CDS (Seca) on Oscam
Re: OpenPLi-py3 #620
-
- PLi® Core member
- 70,219 posts
+1,798
Excellent
Posted 27 September 2022 - 12:45
1. I can not reproduce that, but I run a homebuild from yesterday, so it chould be an issue that has been fixed in the meantime.
2. Is that the simple RSS plugin? Do you have a config I can test with, all I can see is a menu.
Attached Files
-
Screenshot from 2022-09-27 12-41-13.png 88.67KB
4 downloads
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
8 user(s) are reading this topic
0 members, 8 guests, 0 anonymous users
