56 replies to this topic

[zehnisağcan]

Merhaba;

Ben inverto Unicable 2 32 frekans lnb aldım.

Kullanmış olduğum uydu cihazları;Vu+Ultimo 4k - Vu+duo2 hd

İmaj Openatv 7.5(devel)

Vu+Ultimo cihazımda DVB S2x(fbc) tuner var

Vu+Duo2 cihazımda DVB S2 tuner var

Bu iki cihazda da aşağıdaki resimdeki ayarları uyguladım sinyal alamadım.

bana yardımcı olabilirsen sevinirim.

Attached Files

•  20240324_123741.jpg   31.59KB   3 downloads
•  20240324_122647.jpg   112.31KB   2 downloads

Edited by WanWizard, 30 March 2024 - 22:53.
removed copy/paste formatting

[WanWizard]

English please. And please no funny formatting.

 

And you should ask OpenATV questions on their forum, chances are you get more response.

[zehnisağcan]

English please. And please no funny formatting.

 

And you should ask OpenATV questions on their forum, chances are you get more response.

First of all, thank you. I also asked for help on the openatv forum and

Since I use an open-based image and read unicable.xml articles on this subject in the openatv and pli forum, I wanted to get help. I couldn't get a signal from inverto unicable 2 lnb, I programmed it to its service but;

I would be glad if you help me.

[WanWizard]

There is no such thing as "an open based image".

 

We changed our name from PLi to OpenPLi when we made all our sources public, and others copied us, but that doesn't mean they are the same.

 

In OpenPLi you should select the LNB by model name, like in the second picture, and the freqency matches SCR1 for that LNB. So if you have that LNB, the config is correct and the problem is elsewhere.

[zehnisağcan]

"Açık tabanlı bir görüntü" diye bir şey yoktur.

 

Tüm kaynaklarımızı herkese açık hale getirdiğimizde ismimizi PLi'den OpenPLi olarak değiştirdik ve bazılarını başkalarını kopyaladık ancak bunların aynı olduğu anlamına gelmiyor.

 

OpenPLi'de ikinci resimdeki gibi LNB'yi model adına göre seçmeniz ve frekans o LNB için SCR1 ile uyumludur. Yani eğer LNB'niz varsa yapısaldır ve sorun başka yerdedir.

Hocam evet doğrudur bu görseli zaten takip ediyorum, bu konudaki tecrübelerime güvendiğim için yardım istiyorum.

***Sorun nedir mümkünse desteklerinizi bekliyorum***

 

settings dosyam:

config.Nims.0.dvbs.advanced.lnb.1.dictionuser=EN50607

config.Nims.0.dvbs.advanced.lnb.1.lof=unicable

config.Nims.0.dvbs.advanced.lnb.1.unicableLnb.Inverto.product=IDLU-32UL40-UNBOO-OPP

config.Nims.0.dvbs.advanced.lnb.1.unicableLnb.Inverto.vco.IDLU-32UL40-UNBOO-OPP.0=1210

config.Nims.0.dvbs.advanced.lnb.1.unicableLnbManufacturer=Inverto

config.Nims.0.dvbs.advanced.sat.420.lnb=1

config.Nims.0.dvbs.advanced.sats=420

config.Nims.0.dvbs.diseqcA=420

config.Nims.1.dvbs.configMode=nothing

config.Nims.1.dvbs.diseqcA=420

config.Nims.1.dvbs.diseqcB=3601

config.Nims.1.dvbs.diseqcC=3601

config.Nims.1.dvbs.diseqcD=3601

config.Nims.1.dvbs.simpleSingleSendDiSEqC=True

config.Nims.2.dvbs.configMode=nothing

config.Nims.2.dvbs.connectedTo=1

 

Attached Files

•  mytunerconfig.txt   731bytes   1 downloads
•  unicable.xml   55.76KB   2 downloads

Edited by zehnisağcan, 31 March 2024 - 16:18.

[WanWizard]

Again, please post in English !!!

 

And don't ask questions about an ATV image here. That config is not from an OpenPLi image, and ATV is NOT compatible with OpenPLi.

[zehnisağcan]

I'm sorry, I think I've been translated badly. Sir, yes, I am already following it visually, we want to help because I trust these technological experiences. ***What is the problem, I expect your support if possible***

 

settings file:

config.Nims.0.dvbs.advanced.lnb.1.dictionuser=EN50607

config.Nims.0.dvbs.advanced.lnb.1.lof=unicable

config.Nims.0.dvbs.advanced.lnb.1.unicableLnb.Inverto.product=IDLU-32UL40-UNBOO-OPP

config.Nims.0.dvbs.advanced.lnb.1.unicableLnb.Inverto.vco.IDLU-32UL40-UNBOO-OPP.0=1210

config.Nims.0.dvbs.advanced.lnb.1.unicableLnbManufacturer=Tersine

config.Nims.0.dvbs.advanced.sat.420.lnb=1

config.Nims.0.dvbs.advanced.sats=420

config.Nims.0.dvbs.diseqcA=420

config.Nims.1.dvbs.configMode=hiçbir şey

config.Nims.1.dvbs.diseqcA=420

config.Nims.1.dvbs.diseqcB=3601

config.Nims.1.dvbs.diseqcC=3601

config.Nims.1.dvbs.diseqcD=3601

config.Nims.1.dvbs.simpleSingleSendDiSEqC=Doğru

config.Nims.2.dvbs.configMode=hiçbir şey

config.Nims.2.dvbs.connectedTo=1

Attached Files

•  unicable.xml   55.76KB   2 downloads
•  mytunerconfig.txt   731bytes   1 downloads

Edited by zehnisağcan, 1 April 2024 - 09:27.

[littlesat]

That config file is not ours as we have consequent names between unicable and Jess… and not multiple names for the same thing.
We also have a better easier syntax and no work a rounds to get Jess and unicable correctly working.
I would say try openpli and then come back… then we can help.

Edited by littlesat, 1 April 2024 - 14:06.

[zehnisağcan]

That config file is not ours as we have consequent names between unicable and Jess… and not multiple names for the same thing.
We also have a better easier syntax and no work a rounds to get Jess and unicable correctly working.
I would say try openpli and then come back… then we can help.

Sir, when I install the PLI image on a vu+duo2 and vu+ultimo 4k device, can I get a signal from the unicable ll lnb?

My problem that I have difficulty communicating with is that I cannot receive a signal from the unicable ll lnb along with the image.
Thank you.

[Abu Baniaz]

There is nothing wrong with image. Maybe it is how you have configured the hardware and receivers? Please describe fully, provide screenshots/diagram. You cannot use ATV unicable XML file on PLi.

[zehnisağcan]

There is nothing wrong with image. Maybe it is how you have configured the hardware and receivers? Please describe fully, provide screenshots/diagram. You cannot use ATV unicable XML file on PLi.

 

First of all, thank you for your interest.
I made the Vu+:duo2 and Ultimo4k receiver dvbs2 and dvbs2x(fbc) tuner settings as shown in the picture in message 1. Normally, it should be like a universal lnb setting and I should be able to receive a signal, but when I connect the inverto unicable 2 lnb to the system and change the setting, I cannot receive a signal.
I can get 80%-99% signal on universal lnb.

 

I'm trying to get a pli image backup for two devices or I'll try it on the raw pli image.

Edited by zehnisağcan, 2 April 2024 - 11:28.

[zehnisağcan]

I'm trying to get pli image backup for two devices from the forums or I'll try it on the raw pli image.

[Abu Baniaz]

Tuner settings must match the hardware. Posting tuner settings without describing the hardware does not tell the whole story. A unicable LNB cannot be configured like a universal LNB.

 

Please draw a picture of the hardware, including tuner cards/modules and types of cards. Where are the splitters? In which physical connection on card is the signal wire attached? The top physical connection is normally the smaller letter. Please don't mix up tuner slots with tuners. Someone can have two cards in a vu device and somebody else can have a completely different set of two cards. The tuners in Enigma2 will be completely different.  Might be easier to start as simple as possible with only one car. Maybe a screenshot of Menu > Information > Devices will help too.

[zehnisağcan]

Tuner settings must match the hardware. Posting tuner settings without describing the hardware does not tell the whole story. A unicable LNB cannot be configured like a universal LNB.

 

Please draw a picture of the hardware, including tuner cards/modules and types of cards. Where are the splitters? In which physical connection on card is the signal wire attached? The top physical connection is normally the smaller letter. Please don't mix up tuner slots with tuners. Someone can have two cards in a vu device and somebody else can have a completely different set of two cards. The tuners in Enigma2 will be completely different.  Might be easier to start as simple as possible with only one car. Maybe a screenshot of Menu > Information > Devices will help too.

On my Vu+Ultimo4k device, a DVB s2x (FBC) tuner is installed in one slot and the cable coming from the physical external LNB is connected to the upper input of the tuner.
My other device is a Vu+duo2 device, DVB-s2 tuner is connected to the 1st tuner input and the cable from the incoming physical LNB is connected to the top input, sir.
Thank you for your interest and support for me.
After changing the image and trying it, I will try to give more detailed information with the picture.

[Abu Baniaz]

I understand that this is the hardware you have.

 ultimo 4k 1 card satellite fbc.jpg   135.02KB   0 downloads

 

 

You have a signal wire from the Inverto Unicable LNB going to Tuner A. (I did not say tuner slot)

 

All  tuners accessing this LNB must have their own/unique SCR.

 

Tuner A has it's own signal wire, it is not getting signal through another tuner. So say no to this question.

 U4K Tuner A.jpg   88.83KB   0 downloads

 

 

All the other tuners (on that tuner card) are getting signal through tuner A. So yes to the connected question and ensure you select connected to Tuner A. All  tuners accessing this LNB must have their own/unique SCR.

 

Tuner B

 U4K Tuner B.jpg   94.31KB   0 downloads

 

Tuner C

 U4K Tuner C.jpg   94.47KB   0 downloads

 

All the other tuners set same way, just different SCR

 

Tuner H

 U4K Tuner H.jpg   94.46KB   0 downloads

 

 

The file called "settings" in /etc/enigma2 should have these lines after you finish. You can cheat and manually enter these if  you want. You should stop enigma2 with "init 4" command and paste these if you want. Delete the other lines starting with "config.Nims"

 

 
config.Nims.0.advanced.lnb.1.lof=unicable
config.Nims.0.advanced.lnb.1.scrfrequency=1210
config.Nims.0.advanced.lnb.1.scrList=1
config.Nims.0.advanced.lnb.1.unicableManufacturer=Inverto
config.Nims.0.advanced.lnb.1.unicableProduct=IDLU-32UL40-UNBOO-OPP
config.Nims.0.advanced.sat.420.lnb=1
config.Nims.0.advanced.sats=420
config.Nims.0.configMode=advanced
config.Nims.1.advanced.lnb.1.lof=unicable
config.Nims.1.advanced.lnb.1.scrfrequency=1420
config.Nims.1.advanced.lnb.1.scrList=2
config.Nims.1.advanced.lnb.1.unicableManufacturer=Inverto
config.Nims.1.advanced.lnb.1.unicableProduct=IDLU-32UL40-UNBOO-OPP
config.Nims.1.advanced.sat.420.lnb=1
config.Nims.1.advanced.sats=420
config.Nims.1.advanced.unicableconnected=true
config.Nims.1.advanced.unicableconnectedTo=0
config.Nims.1.configMode=advanced
config.Nims.2.advanced.lnb.1.lof=unicable
config.Nims.2.advanced.lnb.1.scrfrequency=1680
config.Nims.2.advanced.lnb.1.scrList=3
config.Nims.2.advanced.lnb.1.unicableManufacturer=Inverto
config.Nims.2.advanced.lnb.1.unicableProduct=IDLU-32UL40-UNBOO-OPP
config.Nims.2.advanced.sat.420.lnb=1
config.Nims.2.advanced.sats=420
config.Nims.2.advanced.unicableconnected=true
config.Nims.2.advanced.unicableconnectedTo=0
config.Nims.2.configMode=advanced
config.Nims.3.advanced.lnb.1.lof=unicable
config.Nims.3.advanced.lnb.1.scrfrequency=2040
config.Nims.3.advanced.lnb.1.scrList=4
config.Nims.3.advanced.lnb.1.unicableManufacturer=Inverto
config.Nims.3.advanced.lnb.1.unicableProduct=IDLU-32UL40-UNBOO-OPP
config.Nims.3.advanced.sat.420.lnb=1
config.Nims.3.advanced.sats=420
config.Nims.3.advanced.unicableconnected=true
config.Nims.3.configMode=advanced
config.Nims.4.advanced.lnb.1.lof=unicable
config.Nims.4.advanced.lnb.1.scrfrequency=984
config.Nims.4.advanced.lnb.1.scrList=5
config.Nims.4.advanced.lnb.1.unicableManufacturer=Inverto
config.Nims.4.advanced.lnb.1.unicableProduct=IDLU-32UL40-UNBOO-OPP
config.Nims.4.advanced.sat.420.lnb=1
config.Nims.4.advanced.sats=420
config.Nims.4.advanced.unicableconnected=true
config.Nims.4.configMode=advanced
config.Nims.5.advanced.lnb.1.lof=unicable
config.Nims.5.advanced.lnb.1.scrfrequency=1020
config.Nims.5.advanced.lnb.1.scrList=6
config.Nims.5.advanced.lnb.1.unicableManufacturer=Inverto
config.Nims.5.advanced.lnb.1.unicableProduct=IDLU-32UL40-UNBOO-OPP
config.Nims.5.advanced.sat.420.lnb=1
config.Nims.5.advanced.sats=420
config.Nims.5.advanced.unicableconnected=true
config.Nims.5.configMode=advanced
config.Nims.6.advanced.lnb.1.lof=unicable
config.Nims.6.advanced.lnb.1.scrfrequency=1056
config.Nims.6.advanced.lnb.1.scrList=7
config.Nims.6.advanced.lnb.1.unicableManufacturer=Inverto
config.Nims.6.advanced.lnb.1.unicableProduct=IDLU-32UL40-UNBOO-OPP
config.Nims.6.advanced.sat.420.lnb=1
config.Nims.6.advanced.sats=420
config.Nims.6.advanced.unicableconnected=true
config.Nims.6.configMode=advanced
config.Nims.7.advanced.lnb.1.lof=unicable
config.Nims.7.advanced.lnb.1.scrfrequency=1092
config.Nims.7.advanced.lnb.1.scrList=8
config.Nims.7.advanced.lnb.1.unicableManufacturer=Inverto
config.Nims.7.advanced.lnb.1.unicableProduct=IDLU-32UL40-UNBOO-OPP
config.Nims.7.advanced.sat.420.lnb=1
config.Nims.7.advanced.sats=420
config.Nims.7.advanced.unicableconnected=true
config.Nims.7.configMode=advanced
 

config.unicable.unicableManufacturer=Inverto
config.unicable.unicableProduct=IDLU-32UL40-UNBOO-OPP

 

Edited by Abu Baniaz, 6 April 2024 - 01:01.

[Abu Baniaz]

I am understanding that your hardware is setup like this picture:

 unicable multi receivers.jpg   35.95KB   0 downloads

 

 

Signal wire from Unicable from unicable output of LNB goes to a unicbale/powerpass splitter.

One signal wire from splitter goes to the Ultimo 4K

One signal wire goes from splitter to the Duo 2. I don't know if you have a twin satellite card or single satellite card in your Duo2.

 

When setting up the tuner with the signal wire from splitter, you should set in a similar way to the other receiver.

Tuner A has it's own signal wire from the spiltter. So the connected question must be no.

You set the satellite,

Select an SCR on the LNB not being used by any other tuner. As an example, select 9. Write them down.

 

This picture is from a Zgemma, so options may be slightly different.

 H9S SE unicable.jpg   93.42KB   0 downloads

[zehnisağcan]

First of all, thank you.
vu+duo2 device tuner back picture is attached.
I'm working on this now.
I installed openpli 8.5xstarr image.
Once again, my efforts were in vain.
***I will upload pictures and files for your support.

[zehnisağcan]

First of all, thank you.
vu+duo2 device tuner back picture is attached.
I'm working on this now.
I installed openpli 8.5xstarr image.
Once again, my efforts were in vain.
***I will upload pictures and files for your support.

Attached Files

•  20240406_160514.jpg   146.31KB   0 downloads
•  unicabley.xml   28.13KB   0 downloads
•  20240406_163026.jpg   124.56KB   0 downloads
•  20240406_163009.jpg   84.54KB   0 downloads

Edited by zehnisağcan, 6 April 2024 - 14:36.

[WanWizard]

And again installed some weird hack image. There has and never will be an OpenPLi 8.5.

 

If you want support here, install OpenPLi downloaded from our website. Or go elsewhere with your questions.

[zehnisağcan]

Ve yine garip bir hack görüntüsü yükledim. OpenPLi 8.5 var ve hiçbir zaman olmayacak.

 

Burada destek istiyorsanız web sitemizden indirdiğiniz OpenPLi'yi yükleyin. Veya sorularınızla başka bir yere gidin.

Yes I am uploading it sir. I may have written the version wrong.
I also upload the develop file.

 

https://dosya.co/mwy...o2_usb.zip.html