Vitaly_k

Member Since 5 Apr 2016
Offline Last Active 06 Jan 2017 16:24

Find content

Posts I've Made

In Topic: GENIATECH MyGica USB TV Stick T230/T220A DVB-T2 Tuner

5 June 2016 - 18:04

I have problem with Geniatech-T230 on Vu+ Zero.

I use drivers repacked from Solo2 (change 'vusolo2' to 'vuzero' in CONTROL file) - http://zalil.su/1564869

Installation of drivers is successful:

Spoiler

But stick do not work. There are no DVB-C/T2 tuners.

Diagnostic info (dmesg):

Spoiler

loop: module loaded

ahci strict-ahci.0: can't get clock

__clk_enable: sata [1]

ahci strict-ahci.0: SSS flag set, parallel bus scan disabled

ahci strict-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode

ahci strict-ahci.0: flags: ncq sntf stag clo slum part

scsi0 : ahci_platform

scsi1 : ahci_platform

ata1: FORCE: PHY spd limit set to 1.5Gbps

ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 87

ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 87

brcmstb_nand: NAND controller driver is loaded

__clk_enable: network [1]

__clk_enable: enet [1]

bcm7552_pm_genet_enable 00

bcmgenet: configuring instance #0 for internal PHY

bcmgenet bcmgenet.0 eth0: link down

__clk_disable: enet [0]

bcm7552_pm_genet_disable 00

__clk_disable: network [0]

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

__clk_enable: usb [1]

bcm7552_pm_usb_enable 00

ehci-brcm ehci-brcm.0: Broadcom STB EHCI

ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1

ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300

ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

ohci-brcm ohci-brcm.0: Broadcom STB OHCI

ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2

ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

usbcore: registered new interface driver usb-storage

mousedev: PS/2 mouse device common for all mice

i2c /dev entries driver

IR NEC protocol handler initialized

IR RC5(x) protocol handler initialized

IR RC6 protocol handler initialized

IR JVC protocol handler initialized

IR Sony protocol handler initialized

IR RC5 (streamzap) protocol handler initialized

IR SANYO protocol handler initialized

ata1: SATA link down (SStatus 0 SControl 310)

IR MCE Keyboard/mouse protocol handler initialized

sdhci: Secure Digital Host Controller Interface driver

sdhci-pltfm: SDHCI platform and OF driver helper

hidraw: raw HID events driver © Jiri Kosina

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

TCP: cubic registered

NET: Registered protocol family 17

Key type dns_resolver registered

PM: CP0 COUNT/COMPARE frequency does not depend on divisor

EBI CS0: setting up NAND flash (primary)

NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix H27U2G8F2CTR-BC)

NAND device: 256MiB, SLC, page size: 2048, OOB size: 64

NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix H27U2G8F2CTR-BC)

NAND device: 256MiB, SLC, page size: 2048, OOB size: 64

brcmnand brcmnand.0: 256MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, Hamming ECC

Bad block table found at page 131008, version 0x01

Bad block table found at page 130944, version 0x01

Creating 4 MTD partitions on "brcmnand.0":

0x000002100000-0x000010000000 : "rootfs"

0x000002100000-0x000010000000 : "rootfs(redundant)"

0x000000200000-0x000000900000 : "kernel"

0x000000900000-0x000000a00000 : "mac"

UBI: attaching mtd0 to ubi0

ata2: SATA link down (SStatus 0 SControl 300)

usb 1-1: new high-speed USB device number 2 using ehci-brcm

usb 1-1: string descriptor 0 malformed (err = -61), defaulting to 0x0409

random: nonblocking pool is initialized

UBI: scanning is finished

UBI: attached mtd0 (name "rootfs", size 223 MiB) to ubi0

UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

UBI: VID header offset: 2048 (aligned 2048), data offset: 4096

UBI: good PEBs: 1780, bad PEBs: 4, corrupted PEBs: 0

UBI: user volume: 1, internal volumes: 1, max. volumes count: 128

UBI: max/mean erase counter: 11/6, WL threshold: 4096, image sequence number: 1647056000

UBI: available PEBs: 0, total reserved PEBs: 1780, PEBs reserved for bad PEB handling: 36

UBI: background thread "ubi_bgt0d" started, PID 52

ALSA device list:

No soundcards found.

UBIFS: parse sync

UBIFS: background thread "ubifs_bgt0_0" started, PID 55

UBIFS: mounted UBI device 0, volume 0, name "rootfs"

UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

UBIFS: FS size: 219541504 bytes (209 MiB, 1729 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)

UBIFS: reserved for root: 0 bytes (0 KiB)

UBIFS: media format: w4/r0 (latest is w4/r0), UUID D959CB2A-5F77-4267-8D5D-CE0088738658, small LPT model

VFS: Mounted root (ubifs filesystem) on device 0:12.

devtmpfs: mounted

Freeing unused kernel memory: 216K (8073a000 - 80770000)

procmk_init

dvb_bcm7362: module license 'Proprietary' taints kernel.

Disabling lock debugging due to kernel taint

DVB: registering new adapter (_vuplus_zero_)

bcm7362: hotplug_callback():

Hotplug - status.connected 1:0:0

bcm7362: hotplug_callback():

Hotplug - connecting HDMI to display 0xe

[GP]:brcm_pwm_init

brcm_demux_init: $Id: bcm_demux.c,v 0.7 $

bcm7362: hotplug_callback():

Hotplug - status.connected 1:1:2

[MPVR]: >> misc_pvr_init

[VID]: 6bcm7335_video_init

[AUD]: 6bcm7335_audio_init

BRCM brcm_dvb0: DVB: registering adapter 0 frontend 0 (BCM7362 FE)...

input: dreambox advanced remote control (native) as /devices/virtual/input/input0

[LCD]: registered

0:0

[DFP]: registered dbox fp

[SC]: registered sci0

system_time_set wakeup mode get

system_time_set wakeup mode get 0xc4

fpga update driver loaded

dvb-usb: found a 'Mygica T230 DVB-T/T2/C' in warm state.

dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.

DVB: registering new adapter (Mygica T230 DVB-T/T2/C)

i2c i2c-3: Added multiplexed i2c bus 4

si2168 3-0064: Silicon Labs Si2168 successfully attached

CPU 1 Unable to handle kernel paging request at virtual address 00000000, epc == 00000000, ra == 00000000

Oops[#1]:

CPU: 1 PID: 190 Comm: modprobe Tainted: P O 3.13.5 #1

task: af71c490 ti: af4f4000 task.ti: af4f4000

$ 0 : 00000000 10008b00 00000000 00010000

$ 4 : af6fa7c8 00000017 00000001 ffff00fe

$ 8 : af4f5fe0 00008b00 fffffffc 00000001

$12 : 00000080 ffffff00 004bc4e0 0044e010

$16 : 00000001 80700000 80780000 00000006

$20 : 10008b08 802f0000 e12e0000 00000001

$24 : 000000fc 800110d0

$28 : af4f4000 af4f5818 00000000 00000000

Hi : 00000001

Lo : e716d300

epc : 00000000 (null)

Tainted: P O

ra : 00000000 (null)

Status: 10008b03 KERNEL EXL IE

Cause : 00800008

BadVA : 00000000

PrId : 0002a065 (Broadcom BMIPS4380)

Modules linked in: si2157 si2168 i2c_mux dvb_usb_cxusb(+) dib0070 dvb_usb dib7000p dibx000_common fpga_directc(PO) brcmfb(O) dvb_bcm7362(PO) procmk(O)

Process modprobe (pid: 190, threadinfo=af4f4000, task=af71c490, tls=771db6a0)

Stack : 00000020 af4f58d0 00000000 8033da80 000000d5 00000001 806ffe08 807293c0

10008b01 00000000 00000000 800a2984 00000178 af4f58d0 af6fa7e0 802f7ad0

af6fa7f8 af4f58c0 00000001 806f0000 fffb8c0b fffffff5 00600100 adc0ae00

af4f5b84 80423db4 00000000 80345b58 8077e3d4 0000001f af72a000 af66c000

00000001 00000001 af4f5970 fffffff5 00000001 e1426030 af6fa7e0 00000000

...

Call Trace:

[<8033da80>] mem32_serial_out+0x0/0x20

[<800a2984>] get_page_from_freelist+0x1d0/0x6ac

[<802f7ad0>] arch_local_irq_restore+0x20/0x30

[<80423db4>] __i2c_transfer+0x90/0xc8

[<80345b58>] create_syslog_header+0xbc/0x1c0

[<e1426030>] si2168_select+0x64/0xd0 [si2168]

[<e141c060>] i2c_mux_master_xfer+0x60/0xa4 [i2c_mux]

[<8030c090>] atomic64_read+0x60/0x84

[<80423db4>] __i2c_transfer+0x90/0xc8

[<80420000>] evdev_connect+0x10c/0x234

[<80424690>] i2c_transfer+0x7c/0xc0

[<80424770>] i2c_master_recv+0x44/0x5c

[<801512ec>] __sysfs_add_one+0x84/0x184

[<e142e18c>] si2157_cmd_execute+0x10c/0x158 [si2157]

[<801514e0>] sysfs_add_one+0x1c/0x60

[<e142e874>] si2157_probe+0x9c/0x168 [si2157]

[<801523c4>] sysfs_do_create_link_sd.isra.2+0x100/0x348

[<e142e7d8>] si2157_probe+0x0/0x168 [si2157]

[<80424040>] i2c_device_probe+0x80/0xf0

[<8034a810>] driver_probe_device+0xb0/0x2d0

[<8034aa30>] __device_attach+0x0/0x64

[<805b0bb4>] klist_next+0x48/0x188

[<8034aa60>] __device_attach+0x30/0x64

[<8034aa30>] __device_attach+0x0/0x64

[<803488bc>] bus_for_each_drv+0x68/0xb0

[<802ed59c>] kobject_uevent_env+0x110/0x51c

[<80055088>] __blocking_notifier_call_chain+0x60/0x88

[<8034a714>] device_attach+0xbc/0xf0

[<80349b90>] bus_probe_device+0xa0/0xdc

[<803479a0>] device_add+0x4cc/0x5d0

[<80346050>] dev_set_name+0x24/0x30

[<802f1df4>] strlcpy+0x0/0x84

[<80090fc8>] try_module_get+0x0/0x58

[<804258d4>] i2c_new_device+0x184/0x1b8

[<80425750>] i2c_new_device+0x0/0x1b8

[<802f78e0>] memset+0x0/0x1c

[<8004394c>] __request_module+0x0/0x308

[<e12daf00>] cxusb_mygica_t230_frontend_attach+0x1e0/0x2c8 [dvb_usb_cxusb]

[<8043a8e4>] dvb_register_device+0x210/0x318

[<e12b7610>] dvb_usb_fe_sleep+0x0/0x80 [dvb_usb]

[<e12b7690>] dvb_usb_fe_wakeup+0x0/0x8c [dvb_usb]

[<80440000>] dvb_ca_en50221_thread_update_delay+0x88/0xf4

[<e12b7b04>] dvb_usb_adapter_frontend_init+0xe8/0x1d8 [dvb_usb]

[<805b50b0>] printk+0x38/0x44

[<805b5078>] printk+0x0/0x44

[<e12b69b4>] dvb_usb_device_init+0x390/0x6fc [dvb_usb]

[<804262e0>] __process_new_adapter+0x0/0x8

[<e12b6624>] dvb_usb_device_init+0x0/0x6fc [dvb_usb]

[<e12da25c>] cxusb_probe+0x214/0x224 [dvb_usb_cxusb]

[<803e8edc>] usb_unlocked_disable_lpm+0x38/0x58

[<803f9330>] usb_probe_interface+0x1f0/0x300

[<8034a164>] driver_sysfs_add+0x78/0xac

[<8034a810>] driver_probe_device+0xb0/0x2d0

[<8034aa94>] __driver_attach+0x0/0xc4

[<803f8930>] usb_device_match+0x5c/0xa0

[<8034ab50>] __driver_attach+0xbc/0xc4

[<805b69f4>] schedule_timeout+0x1b4/0x20c

[<8034aa94>] __driver_attach+0x0/0xc4

[<803487f8>] bus_for_each_dev+0x6c/0xb4

[<805b0f90>] klist_add_tail+0x24/0x70

[<800461f4>] __queue_work+0x150/0x2cc

[<80349e84>] bus_add_driver+0x17c/0x244

[<8034b230>] driver_find+0x1c/0x48

[<8034b2e0>] driver_register+0x84/0x12c

[<803f766c>] usb_register_driver+0x88/0x1a4

[<e12e6000>] cxusb_driver_init+0x0/0x24 [dvb_usb_cxusb]

[<800015b8>] do_one_initcall+0x138/0x1e0

[<800a401c>] free_hot_cold_page+0x34/0x1f8

[<800d1a54>] remove_vm_area+0x88/0xcc

[<800d1b58>] __vunmap+0xc0/0x128

[<80094644>] load_module+0x1d50/0x2248

[<80091074>] unknown_module_param_cb+0x0/0x68

[<800e6a64>] kernel_read+0x2c/0x40

[<80092250>] copy_module_from_fd.isra.51+0x13c/0x1d4

[<800c81a4>] vma_merge+0x1a8/0x2ec

[<80094cb0>] SyS_finit_module+0x88/0xa8

[<80011334>] handle_sys+0x134/0x158

Code: (Bad address in epc)

---[ end trace 81e60fdeaf49c418 ]---

lsmod:

Spoiler

In Topic: USB DVB-C Tuneer DVBSKY t330

19 May 2016 - 14:09

Whether it is possible to work DvbSky T330 on the old-kernel 3.9.6 devices (Vu+ Uno,Solo,Duo) ?

In Topic: DVB-T

7 May 2016 - 19:53

Example TS - http://zalil.su/6675698

In Topic: DVB-T

7 May 2016 - 10:59

No there is not. Your provider has a problem instead.

Aspect ratio in DVB-stream is correct.

For "01 Первый канал" - 16:9, for "05 Пятый канал" - 3:4.

In Topic: DVB-T

7 May 2016 - 10:55

What stb are you using? Many drivers do not calculate PAR correctly when no aspect ratio defined by dvb.

I use Vu+ Duo2 with internal dual DVB-C/T2 tuner

$_1.JPG?set_id=880000500F

ATTENTION !!!

Vitaly_k

Community Stats

Contact Information

User Tools

Friends

Latest Visitors

Posts I've Made

In Topic: GENIATECH MyGica USB TV Stick T230/T220A DVB-T2 Tuner

In Topic: USB DVB-C Tuneer DVBSKY t330

In Topic: DVB-T

In Topic: DVB-T

In Topic: DVB-T