Hi Willy, the following channels from provider "GIB-Solutions AG" in Switzerland have had their channel references changed, and so need updating.
Thanks in advance!
CuriousCorn
1:0:1:1145:1BA:3:FFFF0000:0:0:0 ZDFneo HD
curiousCorn hasn't added any friends yet.
No latest visitors to show
17 November 2015 - 20:40
Hi Willy, the following channels from provider "GIB-Solutions AG" in Switzerland have had their channel references changed, and so need updating.
Thanks in advance!
CuriousCorn
1:0:1:1145:1BA:3:FFFF0000:0:0:0 ZDFneo HD
26 May 2015 - 18:55
Hi,
the following two channels are missing for me (BBC One HD disappeared a few days ago)
1:0:1:276:13D:3:FFFF0000:0:0:0 BBC One HD
1:0:1:2C6:13F:3:FFFF0000:0:0:0 ITV 1 HD
It's a cable provider in Switzerland, GIB-Solutions AG
Thanks,
Chris
9 February 2015 - 13:31
Hi all,
I have a Vu+ Duo2 with the latest OpenPLi image installed.
Problem - I have noticed that when I have viewed a recording to the end, the recording manager (if you can call it that) is then displayed (as I have set it to do). When I then try to exit the recording manager, it ends up in a continuous loop (spinning balls in the top left hand side of the screen).
To resolve this, I need to do a full reboot (like, via the power switch, or reboot -h via telnet). It really kills it dead.
1. I have directories set up on the movie location (hdd), some with spaces in the names
2. It doesn't happen all the time, and seems to primarily occur when watching a recording to the point that it stops at the end and returns to the recording manager screen.
3. Power cycle, or reboot -h required to resolve (thus breaking recordings, and setting my Tuner B to the wrong system, but that issue is in another post)
Are there any logfiles that might indicate what is happening, or has anyone else experienced this ?
In the meantime, I will try to reproduce.
thanks and best regards,
CuriousCorn
9 February 2015 - 13:23
Hi all, strange problem.
I have a Vu+ Duo2 with the latest image and the latest Sundtek drivers installed (as I have a USB Sundtek tuner installed as Tuner C)
All of the tuners are allocated to DVB-C.
However... when I perform a reboot, Tuner B 'resets' itself to DVB-T. This is after a full reboot; restarting Enigma2 does not cause this effect.
To remedy this; I go to Tuner Configuration, where I see the tuner is DVB-T. When I select it, it proudly announces that it is DVB-C. To get it back to DVB-C, I have to change it to DVB-T, then back to DVB-C. Then it is OK - until the next complete reboot and then it's back to DVB-T.
I have re-installed the Sundtek drivers, but this made no difference.
Is there somewhere a configuration conflict, or something? Possibility that it's something on Sundtek's side? Might seem likely, given what I have to do to get Tuner B back to DVB-C. Why would Tuner B suddenly re-invent itself as DVB-T?
Tuners A and C (the Sundtek device) are fine.
What I have not tried so far is removing the Sundtek device and seeing what happens then. I'll try that tonight and report back.
Thanks and best regards,
CuriousCorn
5 February 2015 - 19:06
Hi,
Could you update the following entries in German/Austria/Switzerland ?
1:0:1:f1:14b:3:ffff0000:0:0:0: "Tele M1 HD"
Source: http://www.telem1.ch/programme