227 replies to this topic

[ims]

can you upload crashlog ?

[Vogi]

Hello,

 

I also had problems with HDMI-CEC and my Panasonic TV. Whenever I turned on my STB the Panasonic came up too, but didn't switch to the correct HDMI input. I tried the hotel mode and alsmost every hint I found.

BUt now I have found a solution:

 

I changed the original HdmiCec.py in line 32 from

 

for i in (10, 50, 100, 150, 250):
 

 

 

to

 

to for i in (10, 50, 100, 150, 250,4000):
 

and set the plugin setting to 4000.

Now it seems, that the Panasonic has enough time to start up and to receive the "switch" signal afterwards. I even tried lower values but 3500ms weren't enough.

 

This is most probably not the smartes solution as now all CEC instructions are delayed.

But now I can turn on/off the TV with the STB remote.

 

Maybe someone who knows how to code phyton could extend the plugin to use the long delay only for switching to HDMI input.

Because now, it even takes 4 seconds to turn off the TV after the STB went to Standby and also turning On is delayed...

 

Greets

Vogi

[fulvi0x]

i have problem with HDMI-CEC with my box xtrendET4000 with latest openpli4.0.

My 2 tv are samsung smart tv.

Solution?

The tv remote did not work.

[Yada]

I have a Samsung TV -> hdmi1 -> Samsung receiver -> hdmi 2 -> VUultimo fixed adr 1.2.0.0.

Start TV and Receiver and forward volume to receiver is OK.

This have been running great for months.

I believe with last driver problem with "lost connection with anynet+ device" message on TV after every start occur. The message disappears after a while but very annoying.

 

action ->  StandbyActions power
leave standby
playing 1:0:19:1A91:43:46:E080000:0:0:0:
not pauseable.
not pauseable.
not pauseable.
new service started! trying to download cuts!
download failed, no cuesheet interface
RemovePopup, id = ZapError
allocate channel.. 0043:0046
opening frontend 0
(0)tune
RotorCmd ffffffff, lastRotorCmd ffffffff
prepare_sat System 1 Freq 10778000 Pol 1 SR 25000000 INV 2 FEC 3 orbpos 3592 system 1 modulation 2 pilot 2, rolloff 1
tuning to 1028 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:19:1A91:43:46:E080000:0:0:0:
allocate demux
setLCDBrightness 127
[SEC] set static current limiting
[SEC] invalidate current switch params
[SEC] setVoltage 1
[SEC] sleep 10ms
set sequence pos 3
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 0
(0)fe event: status 0, inversion on, m_tuning 1
[SEC] sleep 500ms
eHdmiCEC: send message 04 
(0)fe event: status 1f, inversion on, m_tuning 2
OURSTATE: ok
[eDVBLocalTimerHandler] channel 0x16de578 running
[eEPGCache] channel 0x16de578 running
[EPGC] next update in 33 min
stop release channel timer
ok ... now we start!!
eventNewProgramInfo 0 0
have 1 video stream(s) (04e7), and 1 audio stream(s) (0cb7), and the pcr pid is 04e7, and the text pid is 18a6
allocate demux
TuxTxt cache cleared
decoder state: play, vpid=1255, apid=3255
DMX_SET_PES_FILTER(0x4e7) - pcr - ok
DEMUX_START - pcr - ok
DMX_SET_PES_FILTER(0xcb7) - audio - ok
DEMUX_START - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PAUSE - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 1 - ok
DMX_SET_PES_FILTER(0x4e7) - video - ok
DEMUX_START - video - ok
VIDEO_FREEZE - ok
VIDEO_PLAY - ok
DMX_SET_PES_FILTER(0x18a6) - ttx - ok
DEMUX_START - ttx - ok
TuxTxt cache cleared
TuxTxt: initialized
TuxTxt service started 18a6
TuxTxt running thread...(18a6)
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
VIDEO_CONTINUE - ok
AUDIO_CONTINUE - ok
disable teletext subtitles
not pauseable.
not pauseable.
[eDVBCAService] new service 1:0:19:1A91:43:46:E080000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:19:1A91:43:46:E080000:0:0:0:
RemovePopup, id = ZapError
eHdmiCEC: send message 82 12 00 
[eDVBLocalTimerHandler] diff is 0
[eDVBLocalTimerHandler] diff < 120 .. use Transponder Time
[eDVBLocalTimerHandler] not changed
[SEC] set dynamic current limiting
PATready
use pmtpid 0132 for service_id 1a91
eHdmiCEC: send message 8E 00 
sdt update done!
eventNewProgramInfo 0 0
have 1 video stream(s) (04e7), and 1 audio stream(s) (0cb7), and the pcr pid is 04e7, and the text pid is 18a6
decoder state: play, vpid=1255, apid=3255
[eDVBCIInterfaces] gotPMT
[eDVBCAService] don't build/send the same CA PMT twice
eHdmiCEC: send message 44 6D 
eHdmiCEC: send message 70 12 00 
eHdmiCEC: received message 32 73 77 65 
eHdmiCEC: received message 84 10 00 04 
eHdmiCEC: received message 84 10 00 05 
eHdmiCEC: received message 32 73 77 65 
eHdmiCEC: received message 87 00 00 F0 
eHdmiCEC: received message 46 
eHdmiCEC: received message 87 00 00 F0 
eHdmiCEC: send message 47 76 75 75 6C 74 69 6D 6F 
eHdmiCEC: received message 80 10 00 12 00 
eHdmiCEC: received message 72 01 
eHdmiCec: volume forwarding to device 05 enabled
eHdmiCEC: received message A0 00 00 F0 23 
eHdmiCEC: received message 9F 
eHdmiCEC: received message 87 00 00 F0 
eHdmiCEC: received message 85 
eHdmiCEC: send message 82 12 00 
eHdmiCEC: received message 8D 02 
eHdmiCEC: send message 8E 00 
eHdmiCEC: received message 84 10 00 05 
eHdmiCEC: received message 84 10 00 05 
eHdmiCEC: received message 84 10 00 05 
eHdmiCEC: received message 84 10 00 05 
eHdmiCEC: received message 84 10 00 05     <- here error message on TV

[theparasol]

I disabled anynet on my samsung -> problem solved! (ok, its dirty but I dont use anynet anyway....)

[Yada]

Well, if i haven't needed anynet i would not have this issue at all, right?

It's very practical to only use one remote to power on everything and change receiver volume with STB remote.

 

Request to any developer: is it possible to change eHdmiCEC debug so to/from is included an change to xx:xx:xx format so it's easy to copy/paste to cec-o-matic site?e

[Yada]

Solved my previous issue at post #84

 

Samsung TV needed a HDMI reset with this simple procedure unplug power cord for a couple of minutes then everything is OK again 

[theparasol]

Tnx Yada for sharing this solution!

[Generation3000]

In which folder i can find the HdmiCec.py file on openpli 4.0 ? Thanks !

[metoo]

usr/lib/enigma2/python/plugins/systemplugins

[Generation3000]

Thanks, also on my Panasonic TV i got it working with a delay of 4 seconds between each signal. Hope there would be a solution, because i'm coming from Merlin 3 Image on Dreambox and also there it was working perfekt.

[chicco]

hi,

is it possible to remap remote buttons?

i have a samsung tv and the anynet cec service does not forward the volume buttons over hdmi cec.

so i can't handle decoder volume using tv remote.

can i remap volumeup and down using different buttons on the remote, red and green for example?

[Yada]

i have a samsung tv and the anynet cec service does not forward the volume buttons over hdmi cec.

My UE55D700 samsung TV do forward volume here, but i prefer the other way around and forward from STB to TV. Anyway booth directions work ok here.

 

Can't check now, but if my memory serves me then i think you need to enable some setting in TV to be able to forward volume from TV.

[chicco]

you can forward the volume setting from the std to the tv. i need to control the stb volume using the tv remote because the tv is without audio control  cause is connected to an external amplifier.

[sowhat]

Hello,

 

openmips hdmi cec (at least turning the tv on/off via receiver) works on my Gigablue Quad HD in connection with Samsung TVs.

I'd like to be able to turn on and off the tv via a button (or two buttons) on the gigablue remote control. The reason: I'd like to listen to radio without having to turn on the tv or using a second remote.

 

Help appreciated!

[Pr2]

Hi,

 

Gigablue is not officially supported by Openpli, you should ask this on your image provider.

 

Pr2

[sowhat]

Hi,

 

Gigablue is not officially supported by Openpli, you should ask this on your image provider.

 

Pr2

 

Thanks for the hint. You are probably right regarding the way I asked my question.

Actually the first question that arises for me is how to use the hdmi test plugin via a console (e. g. via telnet) and at least that question ist about the hdmi test plugin and neither about openpli/openmips or something vendor specific. Even if Gigablue/openmips doesn't allow to reprogram a button on the remote it should be easy to send hdmi cec commands via e.g. an android smarthpone widget.

Edited by sowhat, 30 April 2014 - 09:58.

[sowhat]

Might it be possible to send commands to the following device path? /dev/hdmi_cec

If so, if someone gave me an example of how such a command would look like it would be great.

[gjstroom]

I added the following to the keymap.xml to get the Yellow button of my Samsung tv remote working for the dm800se audio selection screen:

                <key id="KEY_BLUE" mapto="extensions" flags="b" />
        </map>

+       <map context="InfobarAudioSelectionActions">
+               <key id="KEY_YELLOW" mapto="audioSelection" flags="b" />
+       </map>
+
        <map context="SatlistShortcutAction">
                <key id="KEY_BLUE" mapto="nothingconnected" flags="b" />
        </map>

[sakos]

Hello,

 

I would like to ask your support in solving HDMI-CEC interworking issue with OpenPLI4 and a Sony W829 series TV.

 

What is working 

- TV goes to standby when STB goes to standby 
- TV switches on when STB is switched on

- TV volume can be controlled by STB remote.

 

What is NOT working
- TV switches to last input when STB is switched on and not to STB input

- Bravia Sync does not discover the connected STB

- STB neither goes standby nor switches on when TV is switched off/on

- Nothing can be controlled on the STB by using the TV remote.

 

The STB shows 2.0.0.0 address on HDMI1 input.

 

Could you please give me a hint how to solve or debug this problem? I would like to control the STB via the TV remote only.