Jump to content


Photo

HDMI-CEC problems


  • Please log in to reply
227 replies to this topic

Re: HDMI-CEC problems #101 Sjaaky

  • Senior Member
  • 7,443 posts

+41
Good

Posted 2 October 2014 - 21:19

Can you post a screenshot of your hdmicec settings on the tv and on the stb?

Re: HDMI-CEC problems #102 Pr2

  • PLi® Contributor
  • 6,179 posts

+261
Excellent

Posted 3 October 2014 - 16:01

Hi,

 

My 2 cents for the HDMI-CEC problem, I have face also issues with Panasonic and HDMI-CEC the solution was to go into Panasonic TV Menu on the Viera Link (named gived by Panasonic to HDMI-CEC) and then turn off:  Power on Link and Power off Link.

 

Otherwhise TV turned on properly but never switch to the right entry.

 

So when playing around with HDMI also try to disable some features on the TV side this can help the overall HDMI-CEC behavior.

 

Pr2 


NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.

Wanna help with OpenPLi Translation? Please read our Wiki Information for translators

Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)

AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
 


Re: HDMI-CEC problems #103 sakos

  • Member
  • 5 posts

0
Neutral

Posted 4 October 2014 - 13:16

Can you post a screenshot of your hdmicec settings on the tv and on the stb?

Hi,
 
HDMI-CEC settings on STB:
(Note: It is not clear when the physical address is refreshed. At least it shows the correct value aftre power cycle of the STB. Now, the box is connected to HDMI1 input of TV)

 

Attached File  hdmicec.jpg   26.91KB   34 downloads
 
 
HDMI-CEC (Sony Bravia Sync) settings on TV.
Generic settings

Attached File  IMG_20141004_125627878.jpg   40.5KB   20 downloads
 
List of found devices is empty
(It remains empty even after repeated searches)
Attached File  IMG_20141004_125610120.jpg   33.9KB   18 downloads
 
STB apperas on the list if STB has a power cycle while the TV is on.
(Even though the STB is present on the list, the CEC control towards the STB is inoperable. The STB entry will be deleted from the list after the TV is put to standby.)
Attached File  IMG_20141004_133709396.jpg   27.82KB   18 downloads
 
 
I looked into enigma logs and found log entries when STB is sending volume control commands towards the TV, however I did not find any CEC RX message log entry.
 
eHdmiCEC: send message 44 41 
eHdmiCEC: send message 45 
eHdmiCEC: send message 44 42 
eHdmiCEC: send message 45


Edited by sakos, 4 October 2014 - 13:17.


Re: HDMI-CEC problems #104 sakos

  • Member
  • 5 posts

0
Neutral

Posted 4 October 2014 - 18:39

Here is the SW and HW info

Attached File  version.jpg   11.98KB   13 downloads

 

It is a Cloud Ibox2 Plus box. I hope that there is no HW limitation.



Re: HDMI-CEC problems #105 Robinson

  • Senior Member
  • 2,621 posts

+30
Good

Posted 4 October 2014 - 18:45

Your box is not supported by OpenPLi, so I'm afraid you need to seek help somewhere else.


ET9000, OpenPLi 4.0, 13E, 19E

HD51, OpenPLi 6.2, 75E - 30W


Re: HDMI-CEC problems #106 Rob van der Does

  • Senior Member
  • 7,766 posts

+184
Excellent

Posted 5 October 2014 - 05:03

PLi doesn't support ANY clone at all....



Re: HDMI-CEC problems #107 sakos

  • Member
  • 5 posts

0
Neutral

Posted 5 October 2014 - 11:57

Your box is not supported by OpenPLi, so I'm afraid you need to seek help somewhere else.

Damn. This box has Openpli preinstalled by factory.

 

Does your statement mean that you won't help me at all?



Re: HDMI-CEC problems #108 Robinson

  • Senior Member
  • 2,621 posts

+30
Good

Posted 5 October 2014 - 12:01

Neither me (because I have no idea about your box) nor OpenPLi team (because they only support boxes listed in the bottom right corner on this website: http://openpli.org/download/)

It means you have simply been tricked into having an OpenPLi image on your box.


Edited by Robinson, 5 October 2014 - 12:01.

ET9000, OpenPLi 4.0, 13E, 19E

HD51, OpenPLi 6.2, 75E - 30W


Re: HDMI-CEC problems #109 sakos

  • Member
  • 5 posts

0
Neutral

Posted 5 October 2014 - 17:08

Neither me (because I have no idea about your box) nor OpenPLi team (because they only support boxes listed in the bottom right corner on this website: http://openpli.org/download/)

It means you have simply been tricked into having an OpenPLi image on your box.

Ok. Then I will perform test with a supported box type to see if the issue is HW or SW related.



Re: HDMI-CEC problems #110 Yada

  • Member
  • 47 posts

+1
Neutral

Posted 23 November 2014 - 16:20

I tried to disable "use TV remote control" and "disable HDMI-CEC plugin" and it don't work here on VU ultimo.



Re: HDMI-CEC problems #111 ims

  • PLi® Core member
  • 13,781 posts

+214
Excellent

Posted 23 November 2014 - 16:29

I tried to disable "use TV remote control" and "disable HDMI-CEC plugin" and it don't work here on VU ultimo.

what does not work ( when you disable CEC plugin) ?


Kdo nic nedělá, nic nezkazí!

Re: HDMI-CEC problems #112 Yada

  • Member
  • 47 posts

+1
Neutral

Posted 23 November 2014 - 16:37

 

I tried to disable "use TV remote control" and "disable HDMI-CEC plugin" and it don't work here on VU ultimo.

what does not work ( when you disable CEC plugin) ?

 

When i press menu on TV-remote enigma menu appears. Shouldn't do that, right?



Re: HDMI-CEC problems #113 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+541
Excellent

Posted 24 November 2014 - 15:51

Then the remote control of the TV sends a code that the VU Ultimo understands as a command for itself. No HDMI-CEC involved.

* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.


Re: HDMI-CEC problems #114 ims

  • PLi® Core member
  • 13,781 posts

+214
Excellent

Posted 24 November 2014 - 16:14

Then the remote control of the TV sends a code that the VU Ultimo understands as a command for itself. No HDMI-CEC involved.

I think, when is disabled CEC in .py, still are received codes from driver in .cpp. May be, are still sended to e2 ? I think, for me it worked same, but I am not using TV's RC more...


Kdo nic nedělá, nic nezkazí!

Re: HDMI-CEC problems #115 Rob van der Does

  • Senior Member
  • 7,766 posts

+184
Excellent

Posted 24 November 2014 - 18:09

There have been more reports about the need to completely de-install the HDMI-CEC plugin to stop it from receiving commands from the telly and sending commands to the box. Simply disabling the plugin doesn't seem to stop it completely from working.

And as VU uses a completely different IR-language from all other devices, interference with any RC is very unlikely (contrary to the Xtrends, who use a sub-language which results in much interference with many devices).

Edited by SatKiekerd, 24 November 2014 - 18:10.


Re: HDMI-CEC problems #116 ims

  • PLi® Core member
  • 13,781 posts

+214
Excellent

Posted 24 November 2014 - 18:12

  I will see on it tomorrow...


Kdo nic nedělá, nic nezkazí!

Re: HDMI-CEC problems #117 Yada

  • Member
  • 47 posts

+1
Neutral

Posted 24 November 2014 - 18:14

 

Then the remote control of the TV sends a code that the VU Ultimo understands as a command for itself. No HDMI-CEC involved.

I think, when is disabled CEC in .py, still are received codes from driver in .cpp. May be, are still sended to e2 ? I think, for me it worked same, but I am not using TV's RC more...

 

Yes it's cec command that's is sent. Not really a big issue normaly but now i have a new TV and a lot of tweaking in TV menus for best picture settings.

 

But if plugin have a disable setting then it should be disabled both ways. 



Re: HDMI-CEC problems #118 Sjaaky

  • Senior Member
  • 7,443 posts

+41
Good

Posted 24 November 2014 - 22:05

Workaround might be to disable cec on the tv itself.

Re: HDMI-CEC problems #119 ims

  • PLi® Core member
  • 13,781 posts

+214
Excellent

Posted 24 November 2014 - 22:18

hdmicec still receiving rc's keys from hdmi queue and sending it into enigma . I think, better is fix it


Kdo nic nedělá, nic nezkazí!

Re: HDMI-CEC problems #120 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+541
Excellent

Posted 25 November 2014 - 15:14

How about tweaking the proc entries, or is there no proc interface? It might be a bug in the plugin?

* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.



7 user(s) are reading this topic

0 members, 7 guests, 0 anonymous users