12 replies to this topic

[BoxFreak]

Hello,

First of all, thanks for great image and forum.

I have in my Vu+ Duo (kernel 3.1.1) an problem after online update with USB DVB-T stick.
Before the online update the stick was working ok (Installed with Javier3034 instructions from
thread http://openpli.org/f...__1#entry232595 )
After the update the stick does not give any picture, so I re-applied the instructions (reinstalled the modules).
But not there only comes message "timeout reading PAT" and no picture.
Any Idea what could cause this?

dmesg says:
dvb-usb: found a 'TerraTec Cinergy T Stick Dual RC' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw'
dvb-usb: found a 'TerraTec Cinergy T Stick Dual RC' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (TerraTec Cinergy T Stick Dual RC)
af9013: firmware version:5.1.0.0
DVB: registering adapter 1 frontend 0 (Afatech AF9013 DVB-T)...
mxl5007t 0-00c0: creating new instance
mxl5007t_get_chip_id: unknown rev (3f)
mxl5007t_get_chip_id: MxL5007T detected @ 0-00c0
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (TerraTec Cinergy T Stick Dual RC)
af9013: found a 'Afatech AF9013 DVB-T' in warm state.
af9013: firmware version:5.1.0.0
DVB: registering adapter 2 frontend 0 (Afatech AF9013 DVB-T)...
mxl5007t 0-00c0: attaching existing instance
Registered IR keymap rc-terratec-slim
input: IR-receiver inside an USB DVB receiver as /devices/platform/ehci-brcm.0/usb1/1-2/rc/rc0/input2
rc0: IR-receiver inside an USB DVB receiver as /devices/platform/ehci-brcm.0/usb1/1-2/rc/rc0
dvb-usb: schedule remote query interval to 500 msecs.
dvb-usb: TerraTec Cinergy T Stick Dual RC successfully initialized and connected.
usbcore: registered new interface driver dvb_usb_af9015
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
NET: Registered protocol family 10
USB Serial support registered for Keyspan - (without firmware)
USB Serial support registered for Keyspan 1 port adapter
USB Serial support registered for Keyspan 2 port adapter
USB Serial support registered for Keyspan 4 port adapter
usbcore: registered new interface driver keyspan
keyspan: v1.1.5:Keyspan USB to Serial Converter Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver

rtw driver version=v3.3.0_2971.20111128
usbcore: registered new interface driver rtl8192cu
r8712u: module is from the staging directory, the quality is unknown, you have been warned.
usbcore: registered new interface driver r8712u
usbcore: registered new interface driver rt2500usb
usbcore: registered new interface driver rt2800usb
usbcore: registered new interface driver rt73usb
usbcore: registered new interface driver rtl8187
usbcore: registered new interface driver zd1211rw
[VID]: VIDEO_SET_STREAMTYPE 0
...

[littlesat]

Try if

opkg install usbtunerhelper

then restart helps....

[BoxFreak]

Try if

opkg install usbtunerhelper

then restart helps....

Hi,

Thanks, I forgot to mention that I tried this (I saw it in an other thread) no change.
It just tells me that it is already installed, even the force option to reinstall does not help.

[pieterg]

try without usbtunerhelper.
With usbtunerhelper, we have to rely on dvbapi5 support in the vtuner device. Which might be missing for vu+.

Without usbtunerhelper, e2 goes to the usb device directly, avoiding such issues.

[BoxFreak]

try without usbtunerhelper.
With usbtunerhelper, we have to rely on dvbapi5 support in the vtuner device. Which might be missing for vu+.

Without usbtunerhelper, e2 goes to the usb device directly, avoiding such issues.

Hi,

Thanks for the quick answer. How to remove usbtunerhelper? I tried with "opkg remove usbtunerhelper" without success...

[pieterg]

define 'without success'? (as that's exactly how it works)

[BoxFreak]

define 'without success'? (as that's exactly how it works)

The usbtunerhelper is (after the remove) still found with "opkg list usbtunerhelp" (and no change in the behaviour either).

[radxnl]

To see if it is still installed please use

opkg list_installed | grep usbtunerhelper

Using opkg list only shows if it is available from any source not the current status on your machine

[BoxFreak]

To see if it is still installed please use

opkg list_installed | grep usbtunerhelper

Using opkg list only shows if it is available from any source not the current status on your machine

Oh yes of course... my mistake in command. Anyway after removing usbtunerhelper and system restart
, the same problem exists.

list of installed packages:
root@vuduo:/etc/modutils# opkg list_installed |grep mxl
kernel-module-mxl5005s - 3.1.1-r4.5
kernel-module-mxl5007t - 3.1.1-r4.5
root@vuduo:/etc/modutils# opkg list_installed |grep mc
kernel-module-mc44s803 - 3.1.1-r4.5
root@vuduo:/etc/modutils# opkg list_installed |grep mt
enigma2-plugin-extensions-systemtools-for-ppanels - 0.81
kernel-module-mt2060 - 3.1.1-r4.5
mtd-minimal-nand-utils - 1.3.1-r0
root@vuduo:/etc/modutils# opkg list_installed |grep qt10
kernel-module-qt1010 - 3.1.1-r4.5
root@vuduo:/etc/modutils# opkg list_installed |grep af90
firmware-dvb-fe-af9013 - 1.0-r0
firmware-dvb-usb-af9015 - 1.0-r0
kernel-module-af9013 - 3.1.1-r4.5
kernel-module-dvb-usb-af9015 - 3.1.1-r4.5
root@vuduo:/etc/modutils# opkg list_installed |grep dvb-
firmware-dvb-fe-af9013 - 1.0-r0
firmware-dvb-usb-af9015 - 1.0-r0
kernel-module-dvb-pll - 3.1.1-r4.5
kernel-module-dvb-usb - 3.1.1-r4.5
kernel-module-dvb-usb-af9015 - 3.1.1-r4.5
vuplus-dvb-modules - 3.1.1-r4.20120228.2
vuplus-dvb-tools - 1.7-r1
root@vuduo:/etc/modutils# opkg list_installed |grep tda
kernel-module-tda18218 - 3.1.1-r4.5
kernel-module-tda18271 - 3.1.1-r4.5
root@vuduo:/etc/modutils# opkg list_installed |grep usbtuner
root@vuduo:/etc/modutils# dmesg
---clip---
dvb-usb: found a 'TerraTec Cinergy T Stick Dual RC' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw'
dvb-usb: found a 'TerraTec Cinergy T Stick Dual RC' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (TerraTec Cinergy T Stick Dual RC)
af9013: firmware version:5.1.0.0
DVB: registering adapter 1 frontend 0 (Afatech AF9013 DVB-T)...
mxl5007t 0-00c0: creating new instance
mxl5007t_get_chip_id: unknown rev (3f)
mxl5007t_get_chip_id: MxL5007T detected @ 0-00c0
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (TerraTec Cinergy T Stick Dual RC)
af9013: found a 'Afatech AF9013 DVB-T' in warm state.
af9013: firmware version:5.1.0.0
DVB: registering adapter 2 frontend 0 (Afatech AF9013 DVB-T)...
mxl5007t 0-00c0: attaching existing instance
Registered IR keymap rc-terratec-slim
input: IR-receiver inside an USB DVB receiver as /devices/platform/ehci-brcm.0/usb1/1-2/rc/rc0/input2
rc0: IR-receiver inside an USB DVB receiver as /devices/platform/ehci-brcm.0/usb1/1-2/rc/rc0
dvb-usb: schedule remote query interval to 500 msecs.
dvb-usb: TerraTec Cinergy T Stick Dual RC successfully initialized and connected.
usbcore: registered new interface driver dvb_usb_af9015
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
NET: Registered protocol family 10
USB Serial support registered for Keyspan - (without firmware)
USB Serial support registered for Keyspan 1 port adapter
USB Serial support registered for Keyspan 2 port adapter
USB Serial support registered for Keyspan 4 port adapter
usbcore: registered new interface driver keyspan
keyspan: v1.1.5:Keyspan USB to Serial Converter Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver

rtw driver version=v3.3.0_2971.20111128
usbcore: registered new interface driver rtl8192cu
r8712u: module is from the staging directory, the quality is unknown, you have been warned.
usbcore: registered new interface driver r8712u
usbcore: registered new interface driver rt2500usb
usbcore: registered new interface driver rt2800usb
usbcore: registered new interface driver rt73usb
usbcore: registered new interface driver rtl8187
usbcore: registered new interface driver zd1211rw
[VID]: VIDEO_SET_STREAMTYPE 0

Info of the channel shows that it is 1280*720 and MPEG2/HD even though it really is regular SD channel.
Same for all DVB-T channels. Last time I did online upgrade was less than a week ago without problems.
In system information window I can see that the usbtuner looks to be found as do the internal DVB-S2 tuners
(which have no problems...).

[BoxFreak]

Info of the channel shows that it is 1280*720 and MPEG2/HD even though it really is regular SD channel.
Same for all DVB-T channels. Last time I did online upgrade was less than a week ago without problems.
In system information window I can see that the usbtuner looks to be found as do the internal DVB-S2 tuners
(which have no problems...).

Taking an closer looa at the info shown, it is actually the channel info from the working DVB-S channel which was
used before trying to open the DVB-T channel, so incorrect info in the window shown...
Any ideas what to try next?

[BoxFreak]

Ok. So I tried to update the software again and the usbtuner started working again. maybe something had failed during the previous upgrade that caused this.
No notification of anything failing though. But the tuner works now. Thanks for ideas.

[Raitsa]

I had the exact same problem this week so you were not alone.

But luckily a new online update fixed things.

[dylantje]

This stick is not working on mijn 6500 and 9000.

Witch chipset driver i have to download? [ for a cinergyTstick rc ]


Or are there some other options to get i work on mijn stb?