1943 replies to this topic

[radicaldoc]

if it's of any help to anyone i have a fully working solo 2 image for 27.5w if you are interested PM me your welcome to it..

[radicaldoc]

 

 

Tested and success! Here is whole instructions to work all!

 

finally success with Dreambox 920UHD

 

image DreamElite 6 latest OE2.5

oscam 11546 emu798

 

1. in Menu - Setup Network WebInterface

"disable anti-hijacking and token-based security in web interface settings" (big thank you again @matt33 and @Rickk)

 

 

2. (all files with permission 755) create the bbc.service file in /etc/systemd/system

 

insert that 

 

[Unit]

Description = BBC service

 

[Service]

ExecStart = /usr/bin/bbc_pmt_v6.py -t short -d /dev/dvb/adapter0/demux0

 

[Install]

WantedBy = multi-user.target

 

 

3.copy all 3 files from bbc_pmt_v6.rar to usr/bin (all files with permission 755)

 

4. with command (Telnet, you can use DCC) activate service with:

systemctl enable bbc.service

 

5. edit oscam.dvbapi file (in etc/tuxbox/config), file attached below 

 

6. with command (Telnet) init 4 stop Enigma, replace with lamedb (from attachment), init 3 and reboot...

 

also be sure in oscam.conf

pmt_mode                      = 0

 

Hi could some one help me out with this please i am not too great with this stuff so it needs to be simple (like me LOL)

My bbox is a VU+ SOLO 2

 

i did "copy all 3 files from bbc_pmt_v6.rar to usr/bin (all files with permission 755) "
i also copied new Lamebd making sure i did the init 4 and then init 3
The oscam.dvbapi file (in etc/tuxbox/config),

i tried to do the systemctl enable bbc.service but that failed with this..i didn't quite understand that bit..
now when i try to boot i get nothing
just the message "service unavailable check tuner configuration... ???
so i am stuck at the moment any ideas please?

 

i am back now without those files in and working on Oscam Emu with 30w  so can someone explain how i get 27.5w to work as well please on my solo 2  thanks

Attached Files

•  Capture.JPG   17.44KB   6 downloads

[lespat]

May or may not be of interest to you, but I have 27.5w working on several closed source boxes, but more recently, have successfully got 27.5w working on 2 Linux open source boxes (Zgemma 7 & Edision Nino Pro) both running Openvix (with Latest Oscam-Emu on Zgemma & CCcam on Edision) helped along the way by TWOL and others.  The latest various images don't seem to be as complicated as the earlier fixes in this thread were.

[radicaldoc]

 

May or may not be of interest to you, but I have 27.5w working on several closed source boxes, but more recently, have successfully got 27.5w working on 2 Linux open source boxes (Zgemma 7 & Edision Nino Pro) both running Openvix (with Latest Oscam-Emu on Zgemma & CCcam on Edision) helped along the way by TWOL and others.  The latest various images don't seem to be as complicated as the earlier fixes in this thread were.

i dont understand what to do because this is for a different box to mine....... i wnat it to work with Oscam Emu so i can rung BISS and other stuff like CCcam

[lespat]

My Zgemma box is an ARM processor (using OSCAM-EMU) and the Edision is a Mips processor (using CCcam).  The Edision may work on OSCAM-EMU but I already had it set up with CCcam and haven't bothered to change it.  Both only used to receive the BISS channels on 27.5w.  I have a ZIP file with the info & files inside if you think you can make use of it.

[radicaldoc]

Sorted thanks

[radicaldoc]

 

My Zgemma box is an ARM processor (using OSCAM-EMU) and the Edision is a Mips processor (using CCcam).  The Edision may work on OSCAM-EMU but I already had it set up with CCcam and haven't bothered to change it.  Both only used to receive the BISS channels on 27.5w.  I have a ZIP file with the info & files inside if you think you can make use of it.

 

My Zgemma box is an ARM processor (using OSCAM-EMU) and the Edision is a Mips processor (using CCcam).  The Edision may work on OSCAM-EMU but I already had it set up with CCcam and haven't bothered to change it.  Both only used to receive the BISS channels on 27.5w.  I have a ZIP file with the info & files inside if you think you can make use of it.

Thanks bud but i am sorted now all going well apart from a couple of channels not having sound it's usually the HD channels but this time it normal ones oh an more 4+1 and film 4+1

[lespat]

Film4+1 was replaced by More4+1 with a slight change in the lamedb file entry.  Other channels without sound was found to be down to corrupted lamedb file info caused by a channel editing program.  I have a working lamedb file if needed to compare!

[jpuigs]

More4+1 has stopped today evening.

[twol]

Service appears to there - I get a good signal - just not decoding?

Edited by twol, 15 November 2019 - 20:57.

[lespat]

Flysat states that More4+1 has left!

[jpuigs]

But does anybody has picture of it ?

[ManoloMos]

Yes, More4+1 has left from 27,5W.

 

Still on 28.2e

[jpuigs]

According to some comments I read some time ago, this transponder is a mirror of two UK DTT MUXES, PSB1 and PSB3.

More4+1 left PSB3 on 14/11 night., it was moved to COM7., so that's the reason why it has dissapeared from 27.5 W.

[EnoSat]

Hi,

maybe added EPG on BBC-SATBACK from 27W/11495V from another pid as 18 (0x0012) ?

On pid 18 empty , on 58 ok - but pid scrambled in BISS.

Or what added MHEG pid into lamedb ?

Edited by EnoSat, 24 November 2019 - 12:25.

[jpuigs]

I already found it on February that EPG was on PID 58, on page 76, post #1508.

But then it wasn't encrypted.

[sleepy]

Hello, my Dreambox 7020HD is showing some signs of distress, and I am thinking about changing it.

I ask here because of course the new receiver should support as easy as possible these channels (until they last and beyond!).

My Dreambox is working really fine with BBC, so it is just a tyre getting flat, not because I cannot manage the use of my present receiver. It is all "go" at the moment, apart the IR remote (I am now using the smartphone apps through LAN) and some more frequent hiccups.

 

Ideally, since I am changing, the new receiver should support natively multistream channels and also as high as possible signal coding (I am not talking about encryption), such as 16 or even 32 PSK.

The higher the better.

 

I am now using 2 separate sat receiver modules and I would still require those. And if they are of good quality and sensitive I would be even more happy.

 

Ah, a less obvious requirement would be the possibility to manage in some way a serial interface via scripts (and possibly a USB converter if needed,  provided there are  drivers available). That is the way I am presently controlling my LT8700 to have it move my dish. I can do it also externally, but I would love having a all-in-one-box solutions as I have now.

 

Do you have any suggestion?

 

I thank you in advance!

 

Cheers!

 

Sleepy

[v12nut]

Hi all,

Can anyone help with setting up a Zgemma H9 Twin for 27.5w ? had a Mutant previously but lighting took it out and its been a while since I last had to set a box up.

cheers

[v12nut]

Ok, I have all the tv channels from 27,5w working but cannot get any of the radio channels to work on the Zgemma h9 twin with openpli 7.1,  Oscam-emu, Lambdb and softkey file are all I have done to get the tv channels working, any ideas what I am missing?

cheers

[v12nut]

update, I now have all the radio channels clearing!

BUT I do not have ITV HD, Channel 4 HD and channel 5 HD, any ideas?

cheers