644 replies to this topic

[xmr]

@athoik:You can send the PM compiled image of yourself? http://forums.openpl...-18#entry530240 and http://forums.openpl...-18#entry530240

[athoik]

That image deleted long time ago!

Patches for TBS exist already in OpenPLi,SatDreamGr (+mis/pls on experimental), OpenATV 5.4

Edited by athoik, 8 August 2016 - 17:47.

[xmr]

if inserted in the antenna cable tuner's fixed vu plus 4k goes smoothly but when inserted in tuner USB cable tbs nothing works. I saw this problem as if someone had!http://forums.openpl...bs-5925/page-10


(noorsatPosted 8 June 2016 - 15:52


HELLO I TRIED TBS 5925 AND VU+SOLOSE WITH OTHER IMAGE .. THE TBS WAS DETECTED ON THE MENU BUT I DIDN'T FIND PLS AND INPUT STREAM !!
WHAT IS MISSING PLEASE ?)

Edited by Frenske, 9 August 2016 - 10:33.
No need to SHOUT. In case members have a possible solution, I'm certain they will respond.

[xmr]

@athoik :this image is good?(Satdreamgr-4.0-gst1-vusolo4k-20160723) for MIS vu+4k?

[athoik]

Should be fine. The gst1 images are experimental ones with TBS drivers and MIS/PLS.

[xmr]

@athoik:my vu solo in image:satdreamgr-openpli-gst 1 4 It has kernel version is 3.14.28!my question is : needs to be changed with kernel 3.8 ?

[athoik]

There is no 3.8 kernel for solo4k.

The one you have installed is fine and the only one manufacturer provides.

[xmr]

ok thank you!

[xmr]

@athoik:one more question! I have a ZGEMMA H2H  with firmware opendroid 5.5, has installed drivers for 5925. tbs sees tbs5925 USB tuner can catch him on MIS channels 5W-12.5 W?

[athoik]

I don't know if opendroid has the mis/pls patches.

You know where is their sources?


Most probably if there is MIS/PLS in manual scan you are ok.

[xmr]

I think tuner tbs 5925 taken on amazon is defective and scans the H2H ZGEMMA but ... not find any channels. tuner has 2 LEDs ,one red for power  and one green for lock ,the green led does not light.

[albsky]

I finally got my TBS5925, but I have problems configuring the tuners.

My setup:

1 motorized dish

1 cable going to 1 receiver

1 x Inverto Black Unicable Quad 40mm LNB 2 Legacy Ports 0,2dB + 1 Splitter 

1 x TBS Brand TBS5925 USB DVB-S2 TV Box,Unique USB TV Box supports VCM,CCM,ACM and 32APSK

 

The config I need is for VU+ solo 4k. How to set first and second internal DVB-S2 tuners and then how to set TBS?

 

Thanks!

[Huevos]

So how many channel is the LNB and what satellite is it pointing at? Should be on a fixed dish. The whole idea of Unicable is to supply multiple tuners, and that concept makes it incompatible with motorised setups.

 

My personal setup is Unicable II (28.2E on fixed dish) to tuner A. Six FBC links form a chain to that tuner. Tuner B to Universal LNB on a USALS motorised dish.

 

TBS 5925 to another motorised dish, ideally with a positioner, so the 5925 does not have to provide the power to move the dish.

[albsky]

• Output channel 1 (SCR0): 1210 MHz
• Output channel 2 (SCR1): 1420 MHz
• Output Channel 3 (SCR2): 1680 MHz
• Output channel 4 (SCR3): 2040 MHz

I do not have the intention to add more dishes.

Currently, I have set only one USALS tuner and it works perfectly.

 

But, I need to add at least my TBS5925 to use the same dish/lnb.

 

I have tested some configs, but without any luck. When I connect the splitter, and use one cable for the internal tuner(Positioner) and one cable for TBS5925(same as tuner A), it looses signal in some of the channels for tuner A.

 

I would appreciate a lot some help on how to set it up, so I can have the most out of my setup.

 

Thanks!

[Huevos]

For what satellites?

 

I can't see how you can use Unicable on a motor because other tuners on the motor are set to "second cable" and that is not possible with Unicable.

[Rob van der Does]

That sounds like a missing option then.

[littlesat]

I thing the jess-ui changes should make this possible

[Huevos]

You are missing the point. Unicable is for sharing between multiple receivers so putting it on a motor is not an option. I.e. it would be a case of the left hand not knowing what the right hand is doing.

[Rob van der Does]

Or for sharing between multiple tuners in one receiver; why would that option be ruled out?

[Huevos]

Not ruling it out, I just don't think it is a practical use of that hardware. Time isn't an unlimited resource and using it to write a software function that very few people are going to use and that is executed on hardware that itself is run in a crippled configuration (because of user stupidity or stubbornness) is not something many programmers would be interested in.

 

And then at the other end of the scale we have other stupid configurations that are possible in the software but not possible with the hardware. For example, dual DVB-T2/C tuner. Only has one aerial socket, but is possible to configure one tuner to DVB-C and the other to DVB-T2.

Edited by Huevos, 28 August 2016 - 11:04.