@athoik:You can send the PM compiled image of yourself? http://forums.openpl...-18#entry530240 and http://forums.openpl...-18#entry530240
VU Solo 4k support
Re: VU Solo 4k support #581
Re: VU Solo 4k support #582
Posted 8 August 2016 - 17:47
Patches for TBS exist already in OpenPLi,SatDreamGr (+mis/pls on experimental), OpenATV 5.4
Edited by athoik, 8 August 2016 - 17:47.
Unamed: 13E Quattro - 9E Quattro on IKUSI MS-0916
Re: VU Solo 4k support #583
Posted 9 August 2016 - 08:02
(noorsatPosted 8 June 2016 - 15:52
HELLO I TRIED TBS 5925 AND VU+SOLOSE WITH OTHER IMAGE .. THE TBS WAS DETECTED ON THE MENU BUT I DIDN'T FIND PLS AND INPUT STREAM !!
WHAT IS MISSING PLEASE ?)
Edited by Frenske, 9 August 2016 - 10:33.
No need to SHOUT. In case members have a possible solution, I'm certain they will respond.
Re: VU Solo 4k support #584
Re: VU Solo 4k support #585
Re: VU Solo 4k support #586
Re: VU Solo 4k support #587
Posted 10 August 2016 - 11:54
The one you have installed is fine and the only one manufacturer provides.
Unamed: 13E Quattro - 9E Quattro on IKUSI MS-0916
Re: VU Solo 4k support #588
Re: VU Solo 4k support #589
Re: VU Solo 4k support #590
Posted 10 August 2016 - 16:13
You know where is their sources?
Most probably if there is MIS/PLS in manual scan you are ok.
Unamed: 13E Quattro - 9E Quattro on IKUSI MS-0916
Re: VU Solo 4k support #591
Re: VU Solo 4k support #592
Posted 25 August 2016 - 15:31
I finally got my TBS5925, but I have problems configuring the tuners.
Re: VU Solo 4k support #593
Posted 25 August 2016 - 16:36
So how many channel is the LNB and what satellite is it pointing at? Should be on a fixed dish. The whole idea of Unicable is to supply multiple tuners, and that concept makes it incompatible with motorised setups.
My personal setup is Unicable II (28.2E on fixed dish) to tuner A. Six FBC links form a chain to that tuner. Tuner B to Universal LNB on a USALS motorised dish.
TBS 5925 to another motorised dish, ideally with a positioner, so the 5925 does not have to provide the power to move the dish.
Re: VU Solo 4k support #594
Posted 26 August 2016 - 09:45
- Output channel 1 (SCR0): 1210 MHz
- Output channel 2 (SCR1): 1420 MHz
- Output Channel 3 (SCR2): 1680 MHz
- Output channel 4 (SCR3): 2040 MHz
I do not have the intention to add more dishes.
Currently, I have set only one USALS tuner and it works perfectly.
But, I need to add at least my TBS5925 to use the same dish/lnb.
I have tested some configs, but without any luck. When I connect the splitter, and use one cable for the internal tuner(Positioner) and one cable for TBS5925(same as tuner A), it looses signal in some of the channels for tuner A.
I would appreciate a lot some help on how to set it up, so I can have the most out of my setup.
Thanks!
Re: VU Solo 4k support #595
Re: VU Solo 4k support #596
Re: VU Solo 4k support #597
Re: VU Solo 4k support #598
Re: VU Solo 4k support #599
Re: VU Solo 4k support #600
Posted 28 August 2016 - 11:01
Not ruling it out, I just don't think it is a practical use of that hardware. Time isn't an unlimited resource and using it to write a software function that very few people are going to use and that is executed on hardware that itself is run in a crippled configuration (because of user stupidity or stubbornness) is not something many programmers would be interested in.
And then at the other end of the scale we have other stupid configurations that are possible in the software but not possible with the hardware. For example, dual DVB-T2/C tuner. Only has one aerial socket, but is possible to configure one tuner to DVB-C and the other to DVB-T2.
Edited by Huevos, 28 August 2016 - 11:04.
4 user(s) are reading this topic
0 members, 4 guests, 0 anonymous users