Jump to content


Photo

Octagon SF8008 OpenPli Support


  • Please log in to reply
486 replies to this topic

Re: Octagon SF8008 OpenPli Support #141 VraKo

  • Member
  • 7 posts

0
Neutral

Posted 25 February 2020 - 07:38

 

Power off receiver

Connect the USB flash drive that contains the image recovery files It is named sf8008_2018-09-22_recover.zip, 110 MB aprox.). (i'm currently not at home, If you want, I can send it to you tomorrow)

Turn on receiver pressing power button until it gets red and says "boot".

After 10 o 15 seconds, the boot menu will appear (Start 1, start 2, USB network...)

Then you can check that remote works, by pressing the up or down buttons. Don't press OK.

Change the USB flash drive, and connect the one that has the image you want to upload.

select USB... and press OK and will start.....

 

OK, I use these files (sf8008_2018-09-22_recover.zip) to restore the box through the HiTool application.  I'll try it.

 

 

Thanks, the above procedure works, OpenPli image I have installed. I solved this problem with USB offline image installation on other forums (OpenATV or OpenEight) and I was always advised to send the receiver to the manufacturer for repair. However, this is a problem with updating the bootloader in the receiver, which just sometimes did not happen at some time and now the receiver is unable to remedy this. Obviously, recovery using the HiTool application will not help either. Anyway, this is no hardware problem with the front panel! I do not understand why the manufacturer will not allow users any reflash firmware that would fix this problem.


Re: Octagon SF8008 OpenPli Support #142 jpuigs

  • Senior Member
  • 1,143 posts

+32
Good

Posted 25 February 2020 - 12:50

Not a problem, the third-party feed doesn't exist yet. It will be created when the rc moves to release.

 

I noticed that "missing" link because I did an online update, and said that 24 packages available for update.

After updating and rebooting... it said again 24 packages....

Inside a telnet session, i did opkg list-upgradable and nothing appeared, but GUI software update still said 24 packages......

Today I see it has been fixed, as it appears 0 updates.


Enigma is getting old....

 

Spoiler

Re: Octagon SF8008 OpenPli Support #143 jpuigs

  • Senior Member
  • 1,143 posts

+32
Good

Posted 25 February 2020 - 12:51

 

Thanks, the above procedure works, OpenPli image I have installed. I solved this problem with USB offline image installation on other forums (OpenATV or OpenEight) and I was always advised to send the receiver to the manufacturer for repair. However, this is a problem with updating the bootloader in the receiver, which just sometimes did not happen at some time and now the receiver is unable to remedy this. Obviously, recovery using the HiTool application will not help either. Anyway, this is no hardware problem with the front panel! I do not understand why the manufacturer will not allow users any reflash firmware that would fix this problem.

 

 

I asked it 2 days ago in the octagon oficial forum, but nobody has still answered....


Enigma is getting old....

 

Spoiler

Re: Octagon SF8008 OpenPli Support #144 VraKo

  • Member
  • 7 posts

0
Neutral

Posted 25 February 2020 - 13:48

Does Timeshift work? I tried different buttons on the remote control, but only recording is working.
I haven't found the hbbtv plugin anywhere in the plugin download menu. Is it downloadable somewhere?


Re: Octagon SF8008 OpenPli Support #145 noorsat

  • Senior Member
  • 48 posts

+2
Neutral

Posted 25 February 2020 - 14:08

 

Does Timeshift work? I tried different buttons on the remote control, but only recording is working.
I haven't found the hbbtv plugin anywhere in the plugin download menu. Is it downloadable somewhere?

 

It's a release-candidate ( RC) image till  now you can't fiind some plugins , 3rd party plugins feed etc... 

you should wait for the release or stable version .



Re: Octagon SF8008 OpenPli Support #146 betacentauri

  • PLi® Core member
  • 7,185 posts

+323
Excellent

Posted 25 February 2020 - 14:17

Timeshift should work. You need to have an attached storage (HDD, USB stick, NAS) and you maybe need to set Timeshift path in the menu (enable expert mode).
Then by pressing pause Timeshift should start.
Xtrend ET-9200, ET-8000, ET-10000, OpenPliPC on Ubuntu 12.04

Re: Octagon SF8008 OpenPli Support #147 betacentauri

  • PLi® Core member
  • 7,185 posts

+323
Excellent

Posted 25 February 2020 - 14:18

Afaik blindscan issue is now fixed in RC.

Edited by betacentauri, 25 February 2020 - 14:18.

Xtrend ET-9200, ET-8000, ET-10000, OpenPliPC on Ubuntu 12.04

Re: Octagon SF8008 OpenPli Support #148 noorsat

  • Senior Member
  • 48 posts

+2
Neutral

Posted 25 February 2020 - 14:22

Afaik blindscan issue is now fixed in RC.

Good news for users so they should flash the RC of 24/02

Much thanks and good luck.



Re: Octagon SF8008 OpenPli Support #149 Frenske

  • Forum Moderator
    PLi® Core member
  • 27,489 posts

+397
Excellent

Posted 25 February 2020 - 15:04

AFAIK the blindscan is fixed in Develop but not yet in the RC. I tested this morning.


Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.

Dreamboxen heb ik niet meer echt actief. Verder heb ik ook nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET7x00. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. ;) :)
Los van de eerder genoemde modellen heb ik nog wel een rits aan testsamples als Mut@nt 2400HD, HD60, GB UE4K, GB Trio4K, Maxitec Multibox combo en Twin, Octagon sf8008, sf8008 mini en last but nog least enkele modellen van het Grieks Duitse Edision.

Voor centrale opslag van media gebruik ik een Qnap 219P 
met tweemaal 2 Tb harddisks + een Synology DS414 met 12 Tb Totale opslag.

-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".

Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.


Re: Octagon SF8008 OpenPli Support #150 pereira69

  • Senior Member
  • 93 posts

0
Neutral

Posted 25 February 2020 - 15:07

On which box? Not every box is doing v9,the required codec any more. Especially the later broadcom socs.

I have an OctagonSF8008, both with OpenAtv6.3 and 4 or Openeight 6.7 image works perfectly well videos in 4k 50 / 60Hz on youtube our on the mkv player or whatever, I posted behind images of it, on openpli when the video opens for 1s the video and then freezes the box, I have to turn it off and on again. Hope this helps



Re: Octagon SF8008 OpenPli Support #151 WanWizard

  • PLi® Core member
  • 70,340 posts

+1,803
Excellent

Posted 25 February 2020 - 15:10

AFAIK the blindscan is fixed in Develop but not yet in the RC. I tested this morning.

 

That should be the case, I've just checked, I did start a new SF8008 build last night after I updated the enigma2-plugins pinning...


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Octagon SF8008 OpenPli Support #152 WanWizard

  • PLi® Core member
  • 70,340 posts

+1,803
Excellent

Posted 25 February 2020 - 15:11

I have an OctagonSF8008, both with OpenAtv6.3 and 4 or Openeight 6.7 image works perfectly well videos in 4k 50 / 60Hz on youtube our on the mkv player or whatever, I posted behind images of it, on openpli when the video opens for 1s the video and then freezes the box, I have to turn it off and on again. Hope this helps

 

You have a (link to) a file that we can use to test this with?


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Octagon SF8008 OpenPli Support #153 pereira69

  • Senior Member
  • 93 posts

0
Neutral

Posted 25 February 2020 - 18:47

 

I have an OctagonSF8008, both with OpenAtv6.3 and 4 or Openeight 6.7 image works perfectly well videos in 4k 50 / 60Hz on youtube our on the mkv player or whatever, I posted behind images of it, on openpli when the video opens for 1s the video and then freezes the box, I have to turn it off and on again. Hope this helps

 

You have a (link to) a file that we can use to test this with?

Yes I can try to send but I noticed a difference between the openpli images and Openeight 6.7 image, openpli is using the Blurayplayer plugin (1 + git132) and Openeight 6.7 and OpenATV6.3/4 uses a more recent Blurayplayer (1 + git142), it will be for that reason?



Re: Octagon SF8008 OpenPli Support #154 betacentauri

  • PLi® Core member
  • 7,185 posts

+323
Excellent

Posted 25 February 2020 - 18:52

Not likely that this cause the problem.
Xtrend ET-9200, ET-8000, ET-10000, OpenPliPC on Ubuntu 12.04

Re: Octagon SF8008 OpenPli Support #155 pereira69

  • Senior Member
  • 93 posts

0
Neutral

Posted 25 February 2020 - 19:03

Not likely that this cause the problem.

In Openeight 6.7 and OpenATV6.3 / 4 it uses mediaplayer (6.7 + git18113) and Openpli uses mediaplayer (2.7 + git18080), when Openeight 6.7 was launched in testing it also had similar problems, but they were solved, note that I only I want to help and I'm not putting any defects in this openpli image

 

Please try downloud this filme

 


Edited by pereira69, 25 February 2020 - 19:06.


Re: Octagon SF8008 OpenPli Support #156 WanWizard

  • PLi® Core member
  • 70,340 posts

+1,803
Excellent

Posted 25 February 2020 - 19:11

The version is pretty useless I think, as they come from different repositories. So we need to know what the problem, and what was fixed.

 

MediaPlayer in OE-A hasn't been changed in dogs years (https://github.com/o...ons/MediaPlayer) so that isn't it...


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Octagon SF8008 OpenPli Support #157 pereira69

  • Senior Member
  • 93 posts

0
Neutral

Posted 25 February 2020 - 19:23

I don't know how to help anymore, please try to play this video on youtube with the program settings in 4096X3072 as shown in photo1 look for the film I show in photo 2 named LG 4K DEMO HDR 2018 (60FPS) ELBA and vera that stays with screen green as I show in photo 3, as I mentioned before in the other images everything goes perfectly.

 

P.S.If by chance when it comes to youtube settings and are for example 1280X720 or 1920X1080 and when changing to 4096X3072 do not forget to leave the program and re-enter, do not take this call to attention, please test it

Attached Files



Re: Octagon SF8008 OpenPli Support #158 taha

  • Senior Member
  • 30 posts

+2
Neutral

Posted 26 February 2020 - 21:54

After testing the update today this problem appeared

 

Attached File  3.jpg   63.84KB   3 downloads



Re: Octagon SF8008 OpenPli Support #159 WanWizard

  • PLi® Core member
  • 70,340 posts

+1,803
Excellent

Posted 26 February 2020 - 22:04

Is that the latest update? I thought I'd fixed this.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Octagon SF8008 OpenPli Support #160 pereira69

  • Senior Member
  • 93 posts

0
Neutral

Posted 26 February 2020 - 22:47

Is that the latest update? I thought I'd fixed this.

Today’s image isn’t stable, I installed it from scratch and when I try to access the plugins from this message I have in photo 1, I go out and come back in and I can access the plugins, I open YouTube and go to settings and change to 4k, as soon as the video starts for 1 to 2 seconds the music and then the box is blocked, fix factori reset and configured everything again and gives this picture message again, worse when I try to update the green screen softwaer with following log. Thanks

 

 

OpenPLi Enigma2 crash log

crashdate=qua fev 26 21:45:22 2020
compiledate=Feb 26 2020
skin=PLi-FullNightHD/skin.xml
sourcedate=2020-02-26
branch=rc
rev=9d98561
component=Enigma2

stbmodel=sf8008
stbmodel=dm8000
kernelcmdline=console=ttyAMA0,115200 root=/dev/sda2 rootfstype=ext4 rootwait blkdevparts=mmcblk0:1M(boot),1M(bootargs),1M(bootimg),3M(baseparam),4M(pqparam),4M(logo),4M(deviceinfo),4M(softwareinfo),4M(loaderdb),32M(loader),8M(trustedcore),32M(kernel),7000M(rootfs),-(others) coherent_pool=2M mem=1G mmz=ddr,0,0,72M vmalloc=500M MACHINEBUILD=sf8008 OEM=octagon MODEL=sf8008
nimsockets=NIM Socket 0:
imageissue=openpli 7.2-rc %h


Traceback (most recent call last):
  File "/usr/lib/enigma2/python/Components/PluginComponent.py", line 52, in readPluginList
  File "/usr/lib/enigma2/python/Tools/Import.py", line 2, in my_import
  File "/usr/lib/enigma2/python/Plugins/SystemPlugins/SoftwareManager/plugin.py", line 11, in <module>
    from Screens.SoftwareUpdate import UpdatePlugin
ImportError: No module named SoftwareUpdate
REMOVE Peer sf8008
REMOVE Peer sf8008
Traceback (most recent call last):
  File "/usr/lib/enigma2/python/Components/ActionMap.py", line 77, in action
  File "/usr/lib/enigma2/python/Components/ActionMap.py", line 57, in action
  File "/usr/lib/enigma2/python/Screens/Menu.py", line 56, in okbuttonClick
  File "/usr/lib/enigma2/python/Tools/BoundFunction.py", line 9, in __call__
  File "/usr/lib/enigma2/python/Screens/Menu.py", line 68, in runScreen
  File "<string>", line 1, in <module>
ImportError: No module named SoftwareUpdate


dmesg

<4>[1;32mdvb video add event 17 - 7 0
<4>[m
<6>[iframe_confirm:190] iframe confirm
<6>
<4>Enter DMX_OsiPcrChannelDetachSync 0 0
<4>video[0] ready to play
<6>[iframe_finish:208] iframe finish
<6>
<4>DmxPcrAcquire 0 -1073058248
<4>Enter DMX_OsiPcrChannelAttachSync 0 0 4325376
<4>@si2166_i2c_gate_ctrl
<4>@si2166_i2c_gate_ctrl
<4>@OPS diseqc tone = 0(22K-OFF)
<4>@si2166_diseqc_set_voltage OFF
<4>@OPS diseqc tone = 0(22K-OFF)
<4>@si2166_diseqc_set_voltage OFF
<4>[12:38:30:506 ERROR-HI_VPSS]:HI_DRV_VPSS_RelPortFrame[520]:Port = 0 RelPortFrame 0 Failed
<4>proc_vmpeg_0_dst_apply_write 00000001
<4>
<4>stStdTiming[h:640, v:480]
<4>stStdTiming[h:800, v:600]
<4>stStdTiming[h:1024, v:768]
<4>stStdTiming[h:1152, v:864]
<4>stStdTiming[h:1280, v:1024]
<4>stStdTiming[h:640, v:480]
<4>stStdTiming[h:800, v:600]
<4>stStdTiming[h:1024, v:768]
<4>stStdTiming[h:1152, v:864]
<4>stStdTiming[h:1280, v:1024]
<4>stStdTiming[h:640, v:480]
<4>stStdTiming[h:800, v:600]
<4>stStdTiming[h:1024, v:768]
<4>stStdTiming[h:1152, v:864]
<4>stStdTiming[h:1280, v:1024]
<4>bestfit
<4>wol offpanscan
<4>panscan
<4>panscan
<4>panscan
<4>proc_video_videomode_50hz_write [2160p50]
<4>proc_video_videomode_60hz_write [2160p]
<4>proc_video_videomode_24hz_write [2160p24]
<4>panscan
<4>proc_vmpeg_0_dst_apply_write 00000001
<4>
<6>sd 0:0:0:0: [sdb] tag#0 Sense Key : 0x1 [current]
<6>sd 0:0:0:0: [sdb] tag#0 ASC=0x37 ASCQ=0x0
<4>proc_vmpeg_0_dst_apply_write 00000001
<4>
<4>proc_vmpeg_0_dst_apply_write 00000001
<4>
<4>proc_vmpeg_0_dst_apply_write 00000001
<4>

 

Attached Files




4 user(s) are reading this topic

0 members, 4 guests, 0 anonymous users