Posted 28 June 2020 - 18:10
That tuner needs:
opkg install firmware-mn8847x opkg install kernel-module-mn88472 opkg install firmware-dvb-demod-mn88472-02 opkg install kernel-module-tda18250 opkg install firmware-dvb-usb-dib0700-1.20 opkg install kernel-module-dvb-usb-dib0700
From what I can see, all of them are in the feed.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 28 June 2020 - 18:32
I tested on a duo 4k which has same kernel, yes it worked.
Posted 28 June 2020 - 18:33
Posted 28 June 2020 - 18:36
I didn't check 7.2 (probably not, as there were recent changes), but will be in 7.3.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 29 June 2020 - 12:29
I tested on a duo 4k which has same kernel, yes it worked.
Well here in my Duo 4K not (7.2 or 7.3) ... only if you don't "like" MSTIF ... then I test it on Uno 4K SE.
Vu+ Duo 4K (DVB-S2X FBC + MTISF) - Uno 4K SE (DVB-S2 FBC + Xbox USB Tuner) - 2x Vu+ Zero 4K (DVB-S2X + Vu+ USB Turbo Tuner) - 13E, 19.2E, 30W & ONT/Meo
Posted 2 July 2020 - 16:11
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 2 July 2020 - 16:53
And it already works in 7.2 ... the OpenPLI team seems to have been looking for the solution.
I don't know why it doesn't work on Duo 4K with 7.3 ... but I'll see in 7.2.
Anyway, thanks for the job.
Vu+ Duo 4K (DVB-S2X FBC + MTISF) - Uno 4K SE (DVB-S2 FBC + Xbox USB Tuner) - 2x Vu+ Zero 4K (DVB-S2X + Vu+ USB Turbo Tuner) - 13E, 19.2E, 30W & ONT/Meo
Posted 2 July 2020 - 17:10
It works fine on the Duo 4K, as Abu Baniaz reported earlier.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 2 July 2020 - 17:12
Posted 2 July 2020 - 17:19
It was fixed for the Duo 4K in the vendor BSP on May 28th, and that update isn't part of 7.2.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 2 July 2020 - 17:28
Posted 2 July 2020 - 17:29
Posted 2 July 2020 - 17:40
In the setup customize menu you can define a peferred tuner for DVB-C and DVB-T.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 2 July 2020 - 18:21
Well here in my Duo 4K not (7.2 or 7.3) ... only if you don't "like" MSTIF ... then I test it on Uno 4K SE.
Like:
What has that got anything to do with a device working or not?
An MTSIF tuner can only be used on the Vu receivers with this connection socket on the circuit board. A USB tuner can be used on any receiver with driver/kernel support. As well as other devices.
It cost about £70. I bought 3 of the USB tuners for less than £20.
Yes, an internal tuner looks better.
These are the packages I installed
opkg install firmware-mn8847x opkg install kernel-module-mn88472 opkg install firmware-dvb-demod-mn88472-02 opkg install kernel-module-tda18250 opkg install firmware-dvb-usb-dib0700-1.20 opkg install kernel-module-dvb-usb-dib0700
Here is a screenshot of it on a duo 4k on RC 7.3. If it is not working for you, post your install logs and dmesg messages.
pli 7.3 RC xbox one usb tuner.jpg 93.74KB
8 downloads
Edited by Abu Baniaz, 2 July 2020 - 18:23.
Posted 2 July 2020 - 18:41
Confirmed in Duo 4K with 7.2 or 7.3.
Tanks OpenPLI.
Vu+ Duo 4K (DVB-S2X FBC + MTISF) - Uno 4K SE (DVB-S2 FBC + Xbox USB Tuner) - 2x Vu+ Zero 4K (DVB-S2X + Vu+ USB Turbo Tuner) - 13E, 19.2E, 30W & ONT/Meo
Posted 24 January 2021 - 08:20
It's working here too on open pli 7.3 but the signal is 0 db and 0% on the channels, does somebody know why?
Edited by Robertooo, 24 January 2021 - 08:21.
Posted 28 January 2021 - 14:08
Hello, I have a zgemma h9 twin, is it enough to download it from feda to make it move
Posted 10 February 2021 - 17:13
Wavefrontier T90, Vu+ Duo 4k SE (DVB-S2x FBC, DVB-T2, DVB-C USB), Octagon SF4008 (dual DVB-S2, DVB-T2 & DVB-C USB), Mutant HD51 (DVB-S2 & DVB-T2), TBS6920 & TBS6925
0 members, 17 guests, 0 anonymous users
