I did a scan and a new EPGImport after (with the" clear EPG.dat" option enabled).
For all the scanned channels i have only EIT EPG.
Release Openpli 8.1 available in the downloadsection.
Started by WanWizard, 21 Aug 2021 00:29
release problems
398 replies to this topic
Re: Release Openpli 8.1 available in the downloadsection. #141
-
- Senior Member
- 325 posts
+4
Neutral
Posted 12 September 2021 - 11:18
Re: Release Openpli 8.1 available in the downloadsection. #142
-
- Senior Member
- 325 posts
+4
Neutral
Posted 12 September 2021 - 12:45
I did also a full sat scan and same result.
I supress EPGImport and reinstall it and same problem.
Info channel C+ : #SERVICE 1:0:19:2261:438:1:C0AEEC:0:0:0:
Something is wrong but What ?
Re: Release Openpli 8.1 available in the downloadsection. #143
-
- PLi® Contributor
- 6,179 posts
+261
Excellent
Posted 12 September 2021 - 12:46
Check the source that you have selected in EPGImport.
Go into:
Menu - Parameters - System -
Scroll down to switch to the second screen and check that ignore the sub-network in the name space DVB-S is set to enable.
Turn on expert mode if you are not yet in it to see all possible entries.
Go into:
Menu - Parameters - System -
Scroll down to switch to the second screen and check that ignore the sub-network in the name space DVB-S is set to enable.
Turn on expert mode if you are not yet in it to see all possible entries.
Edited by Pr2, 12 September 2021 - 12:47.
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Re: Release Openpli 8.1 available in the downloadsection. #144
-
- Senior Member
- 325 posts
+4
Neutral
Posted 12 September 2021 - 12:58
The name space DVB-S is disable,,only DVB-C is enabled.
Rytec sources are : France_TNT, France Wallonie _ commun, France Mixte, France sport-cinema.
Info channel C+ is #SERVICE 1:0:19:2261:438:1:C0AEEC:0:0:0:
Re: Release Openpli 8.1 available in the downloadsection. #145
-
- PLi® Contributor
- 6,179 posts
+261
Excellent
Posted 12 September 2021 - 14:11
OK as I state you need to set ignore the sub-network in the name space DVB-S to enable (your is disable) and then you won't have problem.
Here is the service reference that I have for Canal+ : 1:0:19:2261:438:1:C00000:0:0:0: (which is the one used in Rytec)
Edited by Pr2, 12 September 2021 - 14:15.
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Re: Release Openpli 8.1 available in the downloadsection. #146
-
- Senior Member
- 325 posts
+4
Neutral
Posted 12 September 2021 - 16:28
With name space DVB-S enabled, it doesn't work, same result.
Re: Release Openpli 8.1 available in the downloadsection. #147
-
- Senior Member
- 325 posts
+4
Neutral
Posted 12 September 2021 - 16:45
I replace manualy in the file .tv for canal+ the value C0AEEC by C00000 and now it works fine for this channel and for all the scanned channels on 12012 V.
All the others scanned channels on 12012V have the C0AEEC value.
?? 
Re: Release Openpli 8.1 available in the downloadsection. #148
-
- Senior Member
- 325 posts
+4
Neutral
Posted 14 September 2021 - 12:09
Why is there the C0AEEC value after a scan and not C00000 value ?
Re: Release Openpli 8.1 available in the downloadsection. #149
-
- Rytec EPG Team
- 17,371 posts
+657
Excellent
Posted 14 September 2021 - 14:24
This namespace is certainly the problem:
C0AEEC
Why some receivers scan this, is a mystery for me.
The subnetwerk setting could be the problem.
Although I have tested this on my own receiver (mutant HD2400) and the result were all :C00000: in the namespace.
Where does it come from?
What receiver are you using and which image is on there?
~~Rytec Team~~
Maxytec Multibox SE OpenPli (used as mediaplayer)
Mutant HD2400 OpenPli
Vu+ Duo OpenPli (backup)
Synology NAS
Sat: 13E, 19.2E, 23.5E and 28.2E
*Pli/Rytec EPG POWERED*
Re: Release Openpli 8.1 available in the downloadsection. #150
-
- PLi® Contributor
- 6,179 posts
+261
Excellent
Posted 14 September 2021 - 15:12
There is an option to ignore the sub network in namespace for DVB-S and he disable it in its configuration (why I don't know). The default is to have it enable to fix this kind of problem.
So with this enable (default) we will just have the orbital position (C0 in hexa means 192 in base10 which mean 19.2°E) in the namespace so C0 0000 while he scan with this disable the sub network is set so it is: C0 AEEC
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Re: Release Openpli 8.1 available in the downloadsection. #151
-
- Senior Member
- 325 posts
+4
Neutral
Posted 14 September 2021 - 19:29
I use a DUO4K with the last release of openpli 8.1.
Re: Release Openpli 8.1 available in the downloadsection. #152
-
- Senior Member
- 325 posts
+4
Neutral
Posted 14 September 2021 - 19:41
If ignore name space DVB-S enabled and i do a new scan, i confirm that on all channels scanned the value is C00000.
Thanks for this information.
Regards
Edited by dudule22, 14 September 2021 - 19:42.
Re: Release Openpli 8.1 available in the downloadsection. #153
-
- Senior Member
- 28 posts
+2
Neutral
Posted 15 September 2021 - 09:05
Hello, for the update of 462 packages of 14 September, it appears a warning message that it is better to flash again .... Is it necessary to flash the image again or do the update normally? If you upgrade normally, do you have to use the telnet command line to reinstall all the packages? Thank you in advance and congratulations to you
Edited by shangi, 15 September 2021 - 09:06.
Re: Release Openpli 8.1 available in the downloadsection. #154
-
- PLi® Core member
- 70,384 posts
+1,807
Excellent
Posted 15 September 2021 - 13:08
For the moment, just do nothing, that update is incomplete. There is an updated build in the making.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: Release Openpli 8.1 available in the downloadsection. #155
-
- Member
- 5 posts
0
Neutral
Posted 15 September 2021 - 13:19
Hello,
I've come across a strange issue. I flashed OpenPLi into a Vu+ Zero v2 and name resolution does not work out of the box, with my router at least. When I set a 3rd party DNS like google, it works fine. This router has no issues with Windows10, Android, iOS and MacOS machines, only with this box.
Maybe its OS is issuing odd DNS requests that the router doesn't like? It's an ISP supplied Compal CH7465LG-LC modem. When flashing another image like OpenATV, the same box works fine. I did cat /etc/resolv.conf and it has the correct nameserver entry.
Re: Release Openpli 8.1 available in the downloadsection. #156
-
- PLi® Core member
- 70,384 posts
+1,807
Excellent
Posted 15 September 2021 - 13:25
Never seen that before. We use the standard resolver from OE, like I assume OE-A images do too...
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: Release Openpli 8.1 available in the downloadsection. #157
-
- Member
- 5 posts
0
Neutral
Posted 15 September 2021 - 14:34
OK, there is definitely something wrong with this router. It seems the only reason the rest of the devices work on the network is because name resolution works over the router's IPv6 DNS server. Since OpenPLi does not pick up IPv6 DNS by default, name resolution fails over IPv4.
Re: Release Openpli 8.1 available in the downloadsection. #158
-
- PLi® Core member
- 70,384 posts
+1,807
Excellent
Posted 15 September 2021 - 15:28
If you use SLAAC for IPv6, the box needs rdnssd to pick up the IPv6 DNS being broadcasted, which isn't available at the moment.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: Release Openpli 8.1 available in the downloadsection. #159
-
- Senior Member
- 71 posts
+2
Neutral
Posted 16 September 2021 - 06:58
I have an issue when running timeshift and switching off the receiver.
If I am on catchup in the middle of a programme and turn off the receiver I am not able to turn on the receiver again.
I need to use the power switch on the backside for restart.
VU+ Duo 4K SE
8.1
Re: Release Openpli 8.1 available in the downloadsection. #160
-
- PLi® Core member
- 10,298 posts
+347
Excellent
Posted 16 September 2021 - 07:38
turn off
standby or?
GigaBlue UHD Quad 4K /Lunix3-4K/Duo 4K
2 user(s) are reading this topic
0 members, 2 guests, 0 anonymous users
